• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.11a
• /
• pp.331-340
• /
• 2001

Elastic-Plasitc Finite element analysis is peformed about the TiN coated medium. The normal contact is simulated by a rigid asperity pressing the surface of an elastic-plastic half-surface. The case of a surface film stiffer than the substrate is considered, and general solutions for the subsurface stress and deformation fields are presented for several coating thickness. Additionally, the critical normal loads for deformation in the substrate and coating fracture are calculated when the yield of TiN film follows the Maximum Principal Stress Theory and Von Mises Theory. The results can be subsumed in failure maps for TiN thin film on steel.

• Corrosion Science and Technology
• /
• v.15 no.6
• /
• pp.290-296
• /
• 2016

This study was conducted in order to examine the effect of burn damage and the resultant anti-corrosion performance. The breakdown and defect of the paint film caused by burn damage are considered to affect not only the macroscopic appearance but also the adhesive force and the anti-corrosion performance of the paint film. The material of the paint film was epoxy paint that is used most widely for heavy-duty coating, and in order to induce burn damage, heat treatment with a torch was applied to the other side of the paint film. Surface and chemical structure changes according to aging were analyzed using FE-SEM and infrared absorption spectroscopy, and variation in the anti-corrosion performance was analyzed through the AC impedance test.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.6
• /
• pp.378-380
• /
• 2000

The epitaxial $BaTiO_{3}$ thin film was prepared on the MgO substrate by the coating-pyrolysis process using a mixed solution of Ba-naphthenate and Ti-naphthenate. The crystal structure of the epitaxial $BaTiO_{3}$ thin film was characterized by XRD ${\theta}/2{\theta}$ scan and asymmetric {303} rocking curve scan. The epitaxial $BaTiO_{3}$ thin film had the cubic phase with the lattice parameter of a = c = 0.4018 nm.

• Journal of Advanced Marine Engineering and Technology
• /
• v.19 no.3
• /
• pp.62-69
• /
• 1995

In order to investigate the effect of TiN coating on corrosion fatigue behavior of metal, the rotary bending corrosion fatigue tests were carried out in 3% NaCl solution by using the round bar specimens of high-speed steel, SKH-9, coated with TiN by PVD method. From the experimental results, fatigue strength of TiN coating steel in air was obvious improvement as compared with that of the substrate because of the restriction of dislocation movement in near surface of the substrate by hard thin film. In 3% NaCl solution, corrosion fatigue life of TiN coating specimen in high stress level was improvement same as in air. But in low stress level, corrosion fatigue life of TiN coating one was equivalent to that without coating, due to much crack initiated from corrosion pits formed at the substrate by failure of coating layer.

• Korean Membrane Journal
• /
• v.7 no.1
• /
• pp.19-27
• /
• 2005

PP hollow fiber membrane was hydrophilized by EVOH dip coating followed by low temperature plasma treatment and UV irradiation. EVOH coating attained high water flux without any prewetting but its stability did not guaranteed at high water permeation rate. At high water permeation rate, water flux declined gradually due to swelling and delamination of the EVOH coating layer causing pore blocking effect. However, plasma treatment reduces the swelling, which suppress delamination of the EVOH coating layer from PP support result in relieving the flux decline. Also, UV irradiation helped the crosslinking of the EVOH coating layer to enhance the performance at low water permeation rate. FT-IR and ESCA analyses reveal that EVOH dip coating performed homogeneously through not only membrane surface but also matrix. Thermogram of EVOH film modified plasma treatment and W irradiation show that crosslinking density of EVOH layer increased. Chemical modification by plasma treatment and UV irradiation stabilized the hydrophilic coating layer to increase the critical flux of the submerged membrane.

• Journal of the Korean Ceramic Society
• /
• v.31 no.7
• /
• pp.795-803
• /
• 1994

Ferroelectric BaTiO3 thin film was produced using BaTi-ethoxide sol. This sol was prepared from BaTi-ethoxide by a partial hydrolysis with ammonia as a basic catalyst and ethylene glycol as a chelating agent. BaTiO3 thin film was prepared from three continuous spin-coating layers of the sol on bare Si(100) wafer at 2500 rpm followed by pyrolysis at $700^{\circ}C$ for 30 min. After the heat treatment, the film was 0.200$\pm$0.010 ${\mu}{\textrm}{m}$ thick and its grain size was 0.059 ${\mu}{\textrm}{m}$. On the other hand, electrical properties were measured for BaTiO3 thin film separately prepared on Au-deposited silicon wafer. The dielectric constant and loss of the BaTiO3 thin film at room temperature was 150~160 and 0.04 respectively, which was measured at 10 kHz and oscillation level of 0.1 V. In the measurements of the dielectric properties at high temperatures, it was observed that the capacitance of the thin film increases steeply, while the dielectric loss reaches maximum around 1$25^{\circ}C$, which corresponds a phase transition from tetragonal to cubic BaTiO3.

• Journal of the Korean Society for Heat Treatment
• /
• v.15 no.3
• /
• pp.118-126
• /
• 2002

TiCN thin films were deposited on tool steels at $510^{\circ}C$ by PECVD from a $TiCl_4+N_2+CH_4+H_2+Ar$ gaseous mixture. The microstructures and preferred orientation were investigated. The micro-scratch tests were performed using a system equipped with an acoustic emission sensor. Critical loads were determined to evaluate the adhesion of TiCN to substrate. The influences of the microstructures of substrates, double layered coatings, and coatings after nitriding(duplex coating) were investigated. The experimental results showed that the microstructures of substrates and double layered coating did not affect the critical loads considerably. By the duplex coating, critical loads were not always increased. In some cases, duplex coatings decreased critical loads significantly despite of absence of black layer. In this study, we tried to relate the results of scratch test to the residual stress analysis. Nitriding before the coating reduces the tensile residual stress in the film, which gives rise to low critical load in scratch test.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2003.04a
• /
• pp.54-69
• /
• 2003

Print gloss is an important attribute of the final printed product. While past work has looked at the influence of key aspects of the coating structure on print gloss, a systematic study has not been reported. The coating roughness, porosity, and pore size are changed by using various combinations of coating materials and by calendering against rough plastic sheets. The print gloss is measured every tenths of a second right after printing, a few minutes after printing, and a few days afterwards. Roughness and porosity affect the print gloss for the first two seconds: this result shows that they influence the ink-film splitting event. Once ink film starts to level, roughness and pore size influences the level of print gloss within the first ten seconds after printing. Porosity modifies the evolution of print gloss for the next few minutes. The decrease in gloss at long times is found to correlate to surface roughness.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.10
• /
• pp.447-450
• /
• 2003

This paper presents a process optimization of antireflection (AR) coating on crystalline Si solar cells. Theoretical and experimental investigations were performed on a double-layer AR (DLAR) coating of MgF$_2$/CeO$_2$. We investigated CeO$_2$ films as an AR layer because they have a proper refractive index of 2.46 and demonstrate the same lattice constant as Si substrate. RF sputter grown CeO$_2$ film showed strong dependence on a deposition temperature. The CeO$_2$ deposited at 40$0^{\circ}C$ exhibited a strong (111) preferred orientation and the lowest surface roughness of 6.87 $\AA$. Refractive index of MgF$_2$ film was measured as 1.386 for the most of growth temperature. An optimized DLAR coating showed a reflectance as low as 2.04% in the wavelengths ranged from 0.4${\mu}{\textrm}{m}$ to 1.1${\mu}{\textrm}{m}$. We achieved the efficiencies of solar cells greater than 15% with 3.12% improvement with DLAR coatings. Further details on MgF$_2$, CeO$_2$ films, and cell fabrication parameters are presented in this paper.

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.3
• /
• pp.7-13
• /
• 2011

In Korea, the car mobile phone service had started in 1961 and with this Korea Mobile Telecommunications Services was established in 1984. Its service was mainly focused on the mobile phone service for the car which led the popularity of the full-scale mobile phone service. There are many kinds of materials, colors and patterns which are the elements of surface coating techniques. In light of that, we are focused on the UV coating that is ranked as an important part of the techniques in this study. In the first, the use of various materials for the cellular phone and surface processing techniques for the cellular phone were searched. On the basis of the results, the experiments of actual consumer experience with the exfoliation of the surface were done and through that we proposed the best way of processing the surface for the cellular phone and the materials. The result of the Wear Test showed that thick coating was detached more slowly and each company differed in their results with UV paints despite the same thickness of UV coating. The seal (UV) exfoliation of cellular phone is deeply related with the film thickness and the film formation when the users use the cellular phones and the exfoliation of the cellular phone surface will be decreased if the manufacturers meet the best conditions for the cellular phone.