• Progress in Superconductivity
• /
• 제7권1호
• /
• pp.77-82
• /
• 2005

We report a successful fabrication of high-quality $SmBa_{2}Cu_{3}O_{7-{\delta}}$ (SmBCO) thin films on $LaAlO_3$(LAO)(100) single crystalline substrates by a modified TFA-MOD method. After the pyrolysis heat treatment of spin-coated films up to $400^{\circ}C$, SmBCO films were fired at various temperatures ranging from 810 to $850^{\circ}C$ in a reduced oxygen atmosphere (10 ppm $O_2$ in Ar). Optimally processed SmBCO films exhibited the zero-resistance temperature ($T_{c,zero}$) of 90.2 K and the critical current density ($J_c$) of $0.8\;MA/cm^2$ at 77K in self-field. Compared with the $J_c$ values (normally, > $2\;MA/cm^2$ at 77 K) of MOD-TFA processed YBCO films, rather depressed $J_c$ values in SmBCO films are most probably attributed to the existence of ${\alpha}$-axis oriented grains.

• Progress in Superconductivity
• /
• 제8권1호
• /
• pp.59-64
• /
• 2006

High $J_c\;YBa_2Cu_3O_x$ superconducting films were fabricated by MOD method using fluorine-free dichloroacetic acid(DCA) as chelating solvent for preparing precursor solution. Coating solutions were prepared by dissolving Y-, Ba- and Cu-acetates in DCA solvent followed by drying in rota vapor to obtain the blue gel that is diluted in methanol and 2-methoxyethanol for adjusting the cation concentration. DCA-MOD precursor solution was coated on a single crystal(001) $LaAlO_3(LAO)$ substrate by a dip coating method with a speed of 25 mm/min. Coated films were calcined at lower temperature up to $500^{\circ}C$ in flowing oxygen atmosphere with a 7.2% humidity. Conversion heat treatment was performed at various temperatures of $780{\sim}810^{\circ}C$ for 2 h in flowing Ar gas containing 1000 ppm oxygen with a humidity of 9.45%. SEM observations showed that films have very dense microstructures for the films prepared at the temperature higher than $800^{\circ}C$ regardless of diluting solvent; methanol or 2-methoxyethanol. X-ray diffraction analysis showed that YBCO grains grew with a (001) preferred orientation. A High critical current density($J_c$) of 1.28 $MA/cm^2$(@77 K and self-field) was obtained id. the YBCO film prepared using 2-methoxyethanol as a solvent.

• 한국초전도ㆍ저온공학회논문지
• /
• 제4권2호
• /
• pp.16-20
• /
• 2002

Bi-axially textured Ni tapes for YBCO coated conductors were Prepared by cold rolling and heat treatment of Ni Powder compacts. The Ni powder used in this study was 5 urn in particle size and 99.99 % in purity. The process of this study consists of filling of hi powder into a rubber mold, cold-isostatically Pressing and sintering of the powder compacts at 110$0^{\circ}C$ for 6h in 96 % Ar - 4 % H$_2$ atmosphere. The sintered compacts were cold rolled with a 5 % step reduction ratio into a 100 micron-thick tapes and then heat-treated at 100$0^{\circ}C$ for various time periods. The (200) texture of Ni tape was successfully developed through the recrystallization heat treatment of the cold rolled Ni tapes. At 100$0^{\circ}C$, the degree of texture of the heat-treated Ni tapes seems not to be significantly affected by the heat-treatment time. The short heat treatment of S min was sufficient to develop the complete (200) cube texture. The degree of in-Plane and out-of-plane texture of the prepared Ni tapes was 8-10$^{\circ}$. The heat treated Ni tapes consisted of equiaxed grains with a size 50-70 microns. and the AFM sol-face roughness was as smooth as 3 nm.

• 한국세라믹학회지
• /
• 제43권12호
• /
• pp.781-787
• /
• 2006

NiO-coated YSZ powder was prepared using heterogeneous precipitation of Ni hydroxides on YSZ particle surface and high energy milling. The powders were characterized by TG/DTA, XRD, XPS, and SEM. Amorphous Ni precipitate completely decomposed into NiO at $500^{\circ}C$ and the growth of NiO crystallites was constrained by the core particles. Nanocrystalline NiO-coated YSZ core-shell structure powder could be obtained after calcination at $800^{\circ}C$ for 2 h. A core-shell powder compact, due to high sinterability, showed a near theoretical density at $1350^{\circ}C$. After reduction at $900^{\circ}C$, interpenetrating Ni-YSZ microstructure with very uniformly distributed fine Ni and YSZ grains and pores was observed. In contrast, the mechanically mixed oxide sample showed less uniform distribution of pores and larger discontinuous We particles as compared with the core-shell samples.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 제5회 학술대회 논문집 일렉트렛트 및 응용기술연구회
• /
• pp.77-81
• /
• 2003

The $Sr_{0.7}Bi_{2.6}Ta_2O_9$(SBT) thin films are deposited on Pt-coated electrode(Pt/$TiO_2/SiO_2$/Si) using RF magnetron sputtering method. The structural and electrical properties of SBT capacitors were influenced with annealing atmosphere. In the XRD pattern, the SBT thin films in all annealed atmosphere had (105) orientation. In the SEM images, Bi-layered perovskite phase was crystallized in all annealing atmosphere and grains largely grew in oxygen annealing atmosphere. The dielectric constant and leakage current density of capacitors annealed oxygen atmosphere are 340 and $2.13{\times}10^{-9}[A/cm^2]$ respectively.

• 한국표면공학회지
• /
• 제34권6호
• /
• pp.537-544
• /
• 2001

In the present study, tin-zinc alloys were coated on a cold-rolled steel sheet with variations of electrolyte concentration, additives quantity and current density employing the Hull cell and circulation cell simulator. With an addition of additives of 2m1/L, tin-zinc deposits containing 10 to 40 percent Zn revealed a good surface appearance with weak acidic electrolytes. The organic additives suppressed the Sn deposition rate and thus increased the zinc contents in tin-zinc coating layers. The zinc contents in the tin-zinc coating layers depended almost linearly on the concentrations of metal ions of tin and zinc. Temperature of the electrolyte affected the composition tin-zinc coating layer. However, the concentration of complexants revealed little effectiveness. The surface morphology of tin-zinc coating showed dense tin and zinc phases with fine equiaxed grains with the high current density.

• 한국세라믹학회지
• /
• 제32권3호
• /
• pp.281-288
• /
• 1995

to prepare the TiO2 thin films, acetyl-acetone(2.4-pentanedione)(1 : 1 molar ratio) was dissolved in the propanol solution of titanium(IV)isopropoxide(Ti[OCH(CH3)2]4). Al, Cr and Sb in the form of soluble salt and niobium ethoxide were added s dopants, respectively. Thin films were coated by the dip-coating method and characteristics were investigated by XRD, SEM and conductance meter. As a result, viscosity of sol was maintained below 4 centi Poise more than 20 days, and crystal growth and diminution of resistivity occurred as the heat treatment temperature increased. The grains grew over 1${\mu}{\textrm}{m}$ and the lowest resistivity was obtained when Nb was added at 130$0^{\circ}C$.

• 한국세라믹학회지
• /
• 제17권4호
• /
• pp.208-212
• /
• 1980

In order to clarify the mechanism of the hydration of supersulphated slag cement, the experiments of suspension hydration were performed in the mixtures of slag+CaSO4+water or NaOH solutions with a liquid/solid ratio of 10. The liquid and solid phase of the suspension was chemically analysed and discussed. In the slag-$CaSO_4$--NaOH system, $Al_2O_3$ was dissolved under high pH condition, and the ettringite was formed by a reaction of $CaSO_4$ and $Al_2O_3$ released in the solution. As hydration progressed, ettringite coated the surface of unhydrated slag grains and inhibited the hydration reaction of slag. $CaSO_4$ was not only an activator for slag hydration, but a reactant in the hydration.

• 한국분말재료학회지
• /
• 제5권4호
• /
• pp.303-311
• /
• 1998

Hard materials such as hardmetal, coated hardmetal, cermet, ceramics and diamond or c-BN sintered compact are a kind of grain-dispersed alloy with high volume of hard particles. These are used for cutting tools, wear-resistant tools, rock bits, high pressure apparatus, etc. The annual production in Japan is about 1.7 billion dollars (200 billion yen). This is greatly owed to the development in science and technology which has been accomplished by applying new concepts such as fine or uniform grain microstructure, orientation of crystal grains, functionally graded material, artificial lattice and coherent bonding in recent years. In this review, the development in recent years in Japan is briefly summarized.

• 한국분말재료학회지
• /
• 제9권6호
• /
• pp.433-440
• /
• 2002

Synthesis and compaction of Al-base nano powders by pulsed discharge method were investigated. The aluminum based powders with 50 to 200 nm of diameter were produced by pulsed wire evaporation method. The powders were covered with very thin oxide layer. The perspective process for the compaction and sintering of nanostructured metal-based materials stable in a wide temperature range can be seen in the densification of nano-sized metal powders with uniformly distributed hard ceramic particles. The promising approach lies in utilization of natural uniform mixtures of metal and ceramic phases, e.g. partially oxidized metal powders as fabricated in our synthesis method. Their particles consist of metal grains coated with oxide films. To construct a metal-matrix material from such powder, it is necessary to destroy the hard oxide coatings of particles during the compaction process. This goal was realized in our experiments with intensive magnetic pulsed compaction of aluminum nanopowders passivated in air.