• International Journal of Automotive Technology
• /
• v.5 no.1
• /
• pp.9-16
• /
• 2004

An experimental study was carried out to characterize the spray atomization process of micro-machined port fuel injectors with a piezoelectric atomization device, which can generate pressure pulsations through vibration of a piezoelectric transducer. In this study, several types of micro-machined arrays such as 30∼200-microns of hole arrays were tested. Both a dual-stream and a central-port injectors with micro-machined arrays were tested and compared with normal port fuel injectors. The spray visualization was conducted to characterize overall spray structure and phase Doppler particle analyzer (PDPA) system was used to quantify the droplet size and velocity. In addition, the pressure history was recorded by using digitized signal from pressure transducer. The results showed that modulation is effective to the spray atomization for tested injectors and atomization performance depends on injector design factors, orifice sizes, and frequency and power of the modulator. A number of resonance frequencies of the modulator was modified by injector parameters and temperature. In addition, our results suggested that design of sufficient space among holes is critical to avoid droplet coalescence in the multi-hole micro-machined injectors.

• Journal of Korea Foundry Society
• /
• v.28 no.3
• /
• pp.129-135
• /
• 2008

The reheating stage of electromagnetically stirred Al billet is a critical factor in the thixoforming process. When reheated to the solid-liquid state, the microstructure evolves to a more globular and more homogeneous structure by a coarsening mechanism, the kinetics depending on the initial microstructure. Microstructural evolution has been characterized by conventional parameters (mean size of particle and shape factor) as a function of holding time in the solid-liquid state. The aim of this study is to report experimental results concerning microstructural evolution in the solid-liquid state of electromagnetically stirred Al billet. The material was elaborated in the form of continuously cast bars solidified with electromagnetic stirring to degenerate the dendritic structure. The choice of the reheating conditions is determined by a dendritic ripening and coalescence mechanism, involving variations of both the shape and size of the particles. The reheating time has to be long enough to allow a minimum degree of spheroidizing, but has to be limited as much as possible in order to avoid excessive ripening. The optimum microstructure was obtained at the reheating temperature of near $584^{\circ}C$ and the holding time of 5 min. The only means of combining high productivity with good casting quality was to use feedstock billets whose microstructure showed rapid transformation characteristics.

• Journal of English Language & Literature
• /
• v.64 no.3
• /
• pp.347-360
• /
• 2018

It is ironic but not coincidental that the loss of Korean sovereignty to Japan roughly paralleled the formation of the idea of Korean ethnic identity. The coalescence of the content of this heretofore amorphous notion of a "pure" and transcendental (in the class sense) ethnic essence was, again ironically, the result both of ideologies taken from (or given by) Japan and resistance to Japanese encroachment. What resulted was the birth of a hybrid (sub) consciousness that was able to accommodate disparate, or even contradictory, realities simultaneously without any sense of contradiction (Christian and shaman for example). If, as Kim Chul has asserted, the colonial period was the most impactful in forming today's Korean society and "giving birth" to today's Korean, it becomes easy to imagine how this formation process included elements of Japanese and western culture. This meant that there was going to be an inevitable cognitive dissonance when these influences collided with the imperatives of ethnic nationalism which became the touchstone for a common Korean identity (North and South). This paper attempts to show how this split-consciousness was manifested in Yeom Sang seop's Manse jeon with the aim of identifying how it affects discourses related to nationalism and identity.

• Journal of the Korean Society of Visualization
• /
• v.19 no.3
• /
• pp.39-45
• /
• 2021

An experiment to visualize fine dust captured by FOG droplet is conducted. Coal dust with 23.56 MMD (Mean Median Diameter) and water with 17.02 MMD is used as fine dust and FOG droplet. Long distance microscope and high-speed camera are used to capture the images of micro-scale particles sprinkled by acrylic duct. After measuring and comparing the size of the coal dust and FOG droplet to MMD, process to seize the coal dust with FOG droplet is recorded in 2 conditions: Fixed and Floated coal dust in the floated FOG droplet flow. In both conditions, a coal dust particle is collided and captured by a FOG droplet particle. A FOG droplet particle attached at the surface of the coal dust particle does not break and remains spherical shape due to surface tension. Combined particles are rotated by momentum of the particle and fallen.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.30 no.4
• /
• pp.150-155
• /
• 2020

Alumina (Al₂O₃) is mainly used as a structural ceramic material and to have good mechanical properties requires a dense microstructure. In commercial fabrication, the liquid phase sintering process is adjusted to reduce the sintering temperature of alumina. In this study, the effect of added amounts of cobalt oxide as a coloring agent on the microstructure and mechanical properties was investigated in the CaO-SiO₂-MgO-system liquid phase sintering of 92 % alumina at various sintering temperatures. When 11 wt% Co₂O₃ was added, a rearrangement of alumina particles, which is the main densification step in liquid phase sintering, occurred from a sintering temperature of 1200℃. Solution re-precipitation and coalescence steps followed from 1300℃ with the grain growth of alumina particles. The addition of excess Co₂O₃ and sintering temperatures above 1400℃ resulted in a decrease in sintered density and Vickers hardness, because of the low viscosity of the liquid phase. In 92 % alumina with the addition of 11 wt% Co₂O₃, a sintered density and Vickers hardness of 3.86 g/㎤ and 12.32 GPa, respectively, were obtained at a sintering temperature of 1350℃.

• Journal of the Korean Ceramic Society
• /
• v.42 no.8 s.279
• /
• pp.561-566
• /
• 2005

For the homogeneous dispersion of $ZrO_2$ particles in $Al_2O_3/ZrO_2$ceramics, Zr-precusors were mixed with oxide $Al_2O_3$powders by chemical routes such as partial precipitation or partial polymerization of Zr-nitrate solutions. In case of the mechanical mixing of ultrafine $Al_2O_3$ and $ZrO_2$ oxide powders, relatively homogeneous dispersion was difficult to achieve so that the particle size and distributions of $ZrO_2$ were relatively inhomogeneous after sintering at high temperature. But when the Zr-Y-hydroxide were co-precipitated to ultrafine $Al_2O_3$ oxide powders followed by calcinations, homogeneous dispersion of nano-sized $ZrO_2$ particles in $Al_2O_3/ZrO_2$ composite ceramics were obtained. But because of the coalescence of dispersed $ZrO_2$ particles, dispersed $ZrO_2$ was grown up to more than 0.2${mu}m$ (200 nm) when sintered at the temperature of higher than $1500^{\circ}C$ But when the sintering temperature was kept to lower than $1400^{\circ}C$ by using nano-sized $\alpha-alumina$, the particle size of dispersed $ZrO_2$ could be sustained below 0.1 ${\mu}m$. But the coalescence of dispersed $ZrO_2$ between $Al_2O_3$ particles could not be avoided so that the mechanical properties were not enhanced contrary to the expectations. So Zr-polyester precursors were precipitated and coated to the surface of ultrafine $\alpha-alumina$ powders by the polymerization of Ethylene Glycol with Citric Acid and Zirconium Nitrate. By this dispersion much more uniform dispersion of $ZrO_2$ was achieved at $1450\~1600^{\circ}C$ of sintering temperature ranges. And due to especially discrete dispersion of $ZrO_2$ between $Al_2O_3$ particles, their mechanical strength was more enhanced than mechanical mixing or hydroxide precipitation methods.

• Journal of the Korean earth science society
• /
• v.41 no.1
• /
• pp.1-18
• /
• 2020

This study presented the effects of the assumed mass-size relationship for snow on the simulated surface precipitation by using cloud microphysics parameterizations in Weather Research and Forecasting (WRF) model. The selected cloud microphysics parameterizations are WRF Double-Moment 6-class (WDM6) and WRF Single-Moment 6-class (WSM6) in the WRF model. We replaced the mass-size relationship for snow in WDM6 and WSM6 with Thompson's mass-size relationship retrieved from measurement data. The sensitivity of the modified WDM6 and WSM6 was tested for the idealized 2-dimensional squall line and winter precipitation system over the Korean peninsula, respectively. The modified WDM6 and WSM6 resulted in the increase of graupel/rain mixing ratios and the decrease of snow mixing ratio in the low atmosphere. The changes of hydrometeor mixing ratio and surface precipitation could be due to the collision-coalescence process between raindrops and snow and the graupel melting process.

• Smart Structures and Systems
• /
• v.26 no.5
• /
• pp.605-617
• /
• 2020

In this study, the experimental tests for the direct tensile strength measurement of Ultra-High Performance Concrete (UHPC) were numerically modeled by using the discrete element method (circle type element) and Finite Element Method (FEM). The experimental tests used for the laboratory tensile strength measurement is the Compressive-to-Tensile Load Conversion (CTLC) device. In this paper, the failure process including the cracks initiation, propagation and coalescence studied and then the direct tensile strength of the UHPC specimens measured by the novel apparatus i.e., CTLC device. For this purpose, the UHPC member (each containing a central hole) prepared, and situated in the CTLC device which in turn placed in the universal testing machine. The direct tensile strength of the member is measured due to the direct tensile stress which is applied to this specimen by the CTLC device. This novel device transferring the applied compressive load to that of the tensile during the testing process. The UHPC beam specimen of size 150 × 60 × 190 mm and internal hole of 75 × 60 mm was used in this study. The rate of the applied compressive load to CTLC device through the universal testing machine was 0.02 MPa/s. The direct tensile strength of UHPC was found using a new formula based on the present analyses. The numerical simulation given in this study gives the tensile strength and failure behavior of the UHPC very close to those obtained experimentally by the CTLC device implemented in the universal testing machine. The percent variation between experimental results and numerical results was found as nearly 2%. PFC2D simulations of the direct tensile strength measuring specimen and ABAQUS simulation of the tested CTLC specimens both demonstrate the validity and capability of the proposed testing procedure for the direct tensile strength measurement of UHPC specimens.

• The Journal of Engineering Geology
• /
• v.21 no.4
• /
• pp.295-304
• /
• 2011

The first step in improving our understanding of uncertainties suclt as rock mass strength parameters and deformation modulus in rock masses around high-level radioactive waste disposal repositories, for improved safety, is to study the process of crack development in intact rock. Therefore, in this study, the fracture process and crack development were examined in samples of KURT granite taken from the KAERI Underground Research Tunnel (KURT), based on acoustic emission (AE) and moment tensor analysis. The results show that crack initiation, coalescence, and unstable crack occurred at rock uniaxial compressive strengths of 0.45, 0.73, and 0.84, respectively. In addition, moment tensor analysis indicated that during the early stage of loading, tensile cracks were predominant. With increasing applied stress, the number of shear cracks gradually increased. When the applied stress exceeded the stress level required for crack damage, unstable shear cracks which directly result in failure of the rock were generated along the failure plane.

• Applied Chemistry for Engineering
• /
• v.27 no.5
• /
• pp.537-542
• /
• 2016

In this study, we have prepared mesophase pitch from pyrolysis fuel oil (PFO) by heterogeneous reforming process. This process was conducted by direct fluorination at various temperature and followed by the heat treatment at $390^{\circ}C$. The reformed pitch was then investigated by softening point analysis, elemental analysis, fourier-transform infrared spectroscopy, high resolution X-ray diffraction and polarization microscope analysis. Carbon contents of reformed pitch increased according to increasing the reaction temperature of fluorination, while oxygen, nitrogen and sulfur contents were completely eliminated. As the fluorination temperature increased, the creation, growth, coalescence and alignment process of mesophase spheres were observed. Also the interlayer spacing of carbon hexagonal planar structure decreased, while its crystalline size increased. In addition, aromatic ring compound contents increased by the condensation polymerization of aliphatic compound. These results can be attributed to the radical reactivity of the fluorine increased as the reaction temperature increased. It was considered that the fluorination reaction could help PFO to generate aromatic compounds, via promoting polymerization by radical reaction.