• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2001.05a
• /
• pp.181-186
• /
• 2001

In this research, we design a microstrip patch antenna with circularly polarized form. First, we study patch form of circularly polarized antenna caused by 90-degree phase difference, and simulate using Ensemble 5.0 to make the left-hand and right-hand circularly polarized antenna. We made circularly polarized antenna using microstrip substrate based on result of the simulation, and analyzed manufactured circularly polarized antenna using Network Analysis.

• Journal of electromagnetic engineering and science
• /
• v.7 no.3
• /
• pp.122-128
• /
• 2007

In this paper, we present the design and measurement of a side-fed circularly-polarized patch antenna with a dielectric loading. The antenna consists of a comer-truncated rectangular patch, an L-shaped ground plane, a dielectric loading material, and a coaxial probe. An antenna operating at the UHF band (910 MHz) for the RFID reader applications is optimized using a commercial software. The size of the patch is reduced by a factor of 1.73 by loading the patch with mono-cast(MC) nylon. Measurements of the fabricated antenna show performance characteristics comparable to those of much larger commercial RFID reader antennas.

• ETRI Journal
• /
• v.33 no.2
• /
• pp.163-168
• /
• 2011

A Fabry-Perot cavity (FPC) antenna producing both high-gain and circularly-polarized (CP) behavior is proposed. To increase antenna gain and obtain CP characteristics, a superstrate composed of square patches with a pair of truncated corners is placed above the linearly polarized patch antenna with an approximately half-wavelength distance from the ground plane at the operating frequency. The proposed antenna has the advantages of high gain, a simple design, and an excellent boresight axial ratio over the operating frequency bandwidth. Moreover, used in an FPC antenna, the proposed superstrate converts a linear polarization produced by a patch antenna into a circular polarization. In addition, the cavity antenna produces left-hand circular-polarization and right-hand circular-polarization when a patch antenna inside the cavity generates x-direction and y-direction polarization, respectively. The measured and simulated results verify the performance of the antenna.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.235-240
• /
• 2005

This paper presents a dual band circularly polarized microstrip patch antenna. The antenna consists of two corner truncated patches implemented in one plane and single feed point. The input signal is directly excited to the patch 2 and the patch 1 is fed from patch 2 by coupling between two patches. The antenna is operated at 900 MHz and 2.45 GHz bands and has the right hand circularly polarized radiation pattern at all. The measured gains of the antenna are 2.95 dBic at 900 MHz band and 4.6 dBic at 2.45 GHz band.

• Journal of information and communication convergence engineering
• /
• v.16 no.3
• /
• pp.197-202
• /
• 2018

This paper reveals the impact of the insertion of electromagnetic band gap (EBG) structures on the performance of circularly polarized (CP) patch-slot antenna with offset slot. Several optimizations are necessary to precise physical parameters in the aim to fix the resonance frequency at 3.2 GHz. The proposed antenna possesses lightweight, simplicity, low cost, and circular polarization ensured by two feeding sources to permit right-hand and left-hand circular polarization process (RHCP and LHCP). The measured results compared with simulation results of the proposed circularly polarized EBG antenna with offset slot show good band operations with –10 dB impedance bandwidths of 9.1% and 36.2% centered at 3.2 GHz, which cover weather radar, surface ship radar, and some communications satellites bands. Our investigation will confirm the simulation and experimental results of the EBG antenna involving new EBG structures.

• Journal of electromagnetic engineering and science
• /
• v.6 no.1
• /
• pp.36-46
• /
• 2006

In this paper, we present a two-element circularly-polarized antenna array for UHF-band RFID reader applications. The antenna element in the array is a comer-truncated rectangular patch placed on a thick plastic-foam dielectric. The patch is fed on one of its edges by a microstrip line printed on a separate thin substrate. The array antenna is fed by a microstrip power divider. Parametric studies on the patch are carried out, from which an optimum design of a single antenna element is derived. The element spacing and the feed network of the array are investigated. A commercial electromagnetic software is employed in the analysis and design of the antenna. The designed array is fabricated and tested. Measurements show good performance characteristics of the fabricated antenna: a 11.2-dBi gain, a reflection coefficient of - 14 dB, an axial ratio less than 3 dB over 3-dB beamwidths of 40 and 60 degrees on two principal planes.

• Journal of the Semiconductor & Display Technology
• /
• v.17 no.2
• /
• pp.20-25
• /
• 2018

In this paper, we have designed circularly polarized array antenna for 5.8GHz microwave wireless power transmission. To obtain high antenna gain, we studied a single patch antenna, a $2{\times}1$ array antenna, a $2{\times}2$ array antenna, a $2{\times}4$ array antenna, and a $4{\times}4$ array antenna. Commonly, characteristics of each antenna have a frequency of 5.8 GHz and Right Hand Circular Polarization(RHCP) of circular polarization. Also, the results were obtained with the design to each antenna that the return loss was less than -10dB and the axial ratio was less than 3dB. The gain of the antennas was 6.08dBi for a single patch antenna, 9.69dBi for a $2{\times}1$ array antenna, 12.99dBi for a $2{\times}2$ array antenna, 15.72dBi for a $2{\times}4$ array antenna and 18.39dBi for a $4{\times}4$ array antenna. When the elements of the array antenna were increased, it was confirmed that it increased by about 3dBi.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2000.11a
• /
• pp.364-368
• /
• 2000

In this paper, we present the design and fabrication of a new circularly polarized circular patch antenna. The antenna is realized using a plastic foam sheet, a Teflon substrate and a metal-coated film. The radiating element is a circular patch proximity-fed by a wide microstrip line. Two thins slots are introduced on the circular patch to obtain a circular polarized radiation. The antenna is optimized using a commercial software. The antenna has 18% impedance bandwidth, 4% axial-ratio band width and 9.12dBi gain.

• Proceedings of the KSRS Conference
• /
• 2008.10a
• /
• pp.441-444
• /
• 2008

This paper describes the development of a circularly polarized microstrip antenna, as a part of the Circularly Polarized Synthetic Aperture Radar (CP-SAR) sensor which is currently under developed at the Microwave Remote Sensing Laboratory (MRSL) in Chiba University. CP-SAR is a new type of sensor developed for the purpose of remote sensing. With this sensor, lower-noise data/image will be obtained due to the absence of depolarization problems from propagation encounter in linearly polarized synthetic aperture radar. As well the data/images obtained will be investigated as the Axial Ratio Image (ARI), which is a new data that hopefully will reveal unique various backscattering characteristics. The sensor will be mounted on an Unmanned Aerial Vehicle (UAV) which will be aimed for fundamental research and applications. The microstrip antenna works in the frequency of 1.27 GHz (L-Band). The microstrip antenna utilized the proximity-coupled method of feeding. Initially, the optimization process of the single patch antenna design involving modifying the microstrip line feed to yield a high gain (above 5 dBi) and low return loss (below -10 dB). A minimum of 10 MHz bandwidth is targeted at below 3 dB of Axial Ratio for the circularly polarized antenna. A planar array from the single patch is formed next. Consideration for the array design is the beam radiation pattern in the azimuth and elevation plane which is specified based on the electrical and mechanical constraints of the UAV CP-SAR system. This research will contribute in the field of radar for remote sensing technology. The potential application is for landcover, disaster monitoring, snow cover, and oceanography mapping.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.42 no.4
• /
• pp.63-68
• /
• 2005

In this paper, the single coaxial fed and circularly polarized patch antenna for the RFID system in 2.45GHz ISM band has been fabricated. The simulation by HFSS, electro-magnetic field simulator was executed in order to decide the location of feed which is difficult to be analysed. The simulated result has the same tendency as the measured one in the view of input impedance with the variation of feed location. VSWR of fabricated antenna is low($\leq$1.2) even in comparatively high dielectric loss epoxy substrate(FR4), and this value is enough for the application of RFID reader antenna.