• 한국정밀공학회지
• /
• 제24권12호
• /
• pp.50-56
• /
• 2007

Femtosecond laser ablation of the Invar alloy and hole drilling for a shadow mask are studied. We used a regenerative amplified Ti-sapphire laser with a 1kHz repetition rate, 184fs pulse duration and 785nm wavelength. Femtosecond laser pulse was irradiated on the Invar alloy with air blowing at the condition of various laser peak power. An ablation characteristic of the Invar alloy was appeared non-linear at $125J/cm^2$ of energy fluence. For the application to a shadow mask, the hole drilling of the Invar alloy with the cross section of a trapezoidal shape was investigated. The ablated micro-holes were characterized using an atomic force microscopy(AFM). The optimal condition of hole pattern f3r a shadow mask was $4\;{\mu}m$ z-axis feed rate, 0.2mm/s circular velocity, $26.4{\mu}J$ laser peak power. With the optimal processing condition, the fine circular hole shape without burr and thermal damage was achieved. Using the femtoseocond laser system, it demonstrates excellent tool for the Invar alloy micro-hole drilling without heat effects and poor edge.

• 융복합기술연구소 논문집
• /
• 제5권2호
• /
• pp.27-32
• /
• 2015

Air intakes are an essential component of aircraft engines. They are mainly used to offer uniform airflows to engine faces. Fighter aircraft have to mask the engine face inside the fuselage in order to reduce the Radar Cross Section(RCS). Therefore, offset intakes like a S-Duct are one of promising components for this purpose. During a fight, it is unavoidable that the flow will enter the intakes at some face angles other than zero. In this case, the performance of the aircraft engine will be influenced to the angle of incidence. In this study, the CFD analysis of the semi-circular S-Duct with AR(0.5,0) is performed to investigate the influence of the angle of incidence on the performance of the S-Duct using a distortion coefficient. To consider the adverse pressure gradient, a $k-{\omega}$ SST turbulence model is employed. The secondary flow and flow separation are observed for all computational cases. It is found that the positive incidence angle produces the best performances.

• 대한기계학회논문집
• /
• 제17권12호
• /
• pp.3208-3216
• /
• 1993

Heat transfer characteristics of the laminar oscillating flow in a circular pipe have been studied under the condition that the wall temperature of the pipe is distributed sinusoidally with the axial direction. The axial velocity was assumed to be uniform in radial direction and the temperature field was analyzed by means of the perturbation method. The results show that the difference between wall and section-time-averaged fluid temperature increases as the oscillating frequency increases and eventually converges to a constant value which is determined by the ratio of swept distance to the characteristic length of wall temperature distribution. Also it is shown that the dominant variable in the heat transfer process when swept distance ratio is greater than 1 is not thermal Womersley number(F) but thermal Womersley number multiplied by the square root of swept distance ratio. The variation of the time-averaged Nusselt number is obtained as a function of F. The results indicate that Nusselt number is proportional to $F_{\epsilon}^{1/2}$ when both of F and .epsilon. are much greater than 1.

• Ocean and Polar Research
• /
• 제23권3호
• /
• pp.305-310
• /
• 2001

This paper describes a floating fish reef technology for enhancement of fisheries productivity in the muddy areas. The floating fish reef was composed of main fish cage, anchor rope and concrete anchor blocks. Main fish cage was made up of 12 steel buoys measuring 0.37m in diameter and 1.5m long, polyethylene (PE) netting and circular steel rings. Each steel buoy had buoyancy of 110kgf. The size of main fish cage was 1.96 m in diameter and 3.75m in length. Monitoring on its durability was made for eight months after installation. The steel buoys fixed on main fish cage and nettings were observed to be kept safely. The wet weight of fouling organisms per unit area$(m^2)$ was 26.6kgf after eight months. Reduction in the cross-section of steel buoys and circular steel rings of main fish cage were not found. In addition, any cracks on the concrete anchor blocks were not observed.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2006년도 제27회 추계학술대회논문집
• /
• pp.89-92
• /
• 2006

본 연구는 원통형 탱크에서의 유동의 배수 특성을 메시형 회전억제장치의 중앙 구멍의 크기를 변화하면서 연구하였다. 그리고 원통 탱크 내부의 회전을 억제하는 다른 형태의 회전 억제장치를 사용하여 그에 따른 유동의 변화를 규명하고자 하였다. 측정 장치는 PIV을 이용하여 수행하였으며, 회전이 탱크 내부에 회전이 없는 경우와 있는 경우에 측정하였으며, 배수가 없는 경우와 배수가 있는 경우도 측정하였고 원통 탱크의 수직면과 수평면을 측정하였다.

• 대한기계학회논문집B
• /
• 제20권5호
• /
• pp.1613-1623
• /
• 1996

In this paper, two discretization methods, hybrid and QUICK, are tested for the Navier-Stokes equations written in general nonorthogonal body fitted coordinates. Comparison is made by calculating two laminar flows at low Reynolds numbers of 10 - 100. One is a two-dimensional channel of gradually expanding cross section and the other is an axisymmetric flow through a circular tube having a circular constriction. Results show that the QUICK scheme results in a numerical solution more accurate than that of hybrid. The QUICK scheme also shows faster convergence for both test cases. As the number of grid points increases, all numerical solutions converge with more oscillation. The number of grid points in the y-direction(cross stream direction) is also shown to play a significant role in the approximation of convection term within separated flow zone.

• 대한토목학회논문집
• /
• 제14권6호
• /
• pp.1281-1288
• /
• 1994

평면에서 곡선을 이루는 들보는 흔히 뒬효과를 고려한 원형곡선부재로 설계된다. 본 연구에서는 곡선교를 단면이 일축대칭이고 단순지지된 원형곡선부재로 이상화시켰다. 경계조건을 만족하는 변위형상함수를 퓨리어급수로 전개하고 이로부터 곡선교의 전동수방정식을 유도하였다. 곡선형교의 특성을 나타낼 수 있는 매개변수-중심각, 곡률계수 및 단면의 대칭성계수-의 변화에 따른 원형곡선부재의 고유진동수 특성분포를 보였다. 몇 개의 해석예를 통하여 고유진동수에 미치는 매개변수의 효과를 조사하였다.

• 대한기계학회논문집A
• /
• 제24권10호
• /
• pp.2487-2495
• /
• 2000

The acoustic characteristics of expansion chamber will be changed with the variation of inlet/outlet location due to the higher order acoustic mode in a high frequency in which the plane wave theory is not available. In this paper, the acoustic performance of reactive type expansion chamber with circular cross-section is analyzed by using the modified mode matching theory. The sensitivity analysis of four-pole parameters with respect to the location of inlet and outlet is also suggested to increase the acoustic performance. The acoustic power transmission coefficient is used as cost function, and the location of inlet and outlet is used as design variables. The steepest descent method and SUMT algorithm are used for optimization technique. Several results showed that the expansion chamber with optimally located inlet/outlet had better acoustic performance than concentric expansion chamber.

• 한국지진공학회논문집
• /
• 제21권1호
• /
• pp.49-57
• /
• 2017

In order to avoid collapse of bridges in earthquakes bridge piers are generally designed to attain sufficient ductility. This full-ductility design method has merits for securing the seismic safety readily against strong earthquakes but, it has weakness of high cost design because of excessive safety margin. Recently, in many countries with high seismic technologies, the seismic design concept tends to shift from the collapse prevention design to the performance-based one which requires different performance (damage) levels according to the structural importance. In order to establish this performance-based design method the displacement ductility of confined concrete members should be evaluated quantitatively. And the stress-strain model of confined concrete is indispensible in evaluating displacement ductility. In this study, 6 test groups with different lateral reinforcement ratios were prepared. 10 same specimens with circular section for each group were tested to obtain more reliable test results. The characteristic values necessary for composing the stress-strain model were obtained from experiments. Based on these characteristic values the new stress-strain model modifying the Hoshikuma's one has been proposed.

• 한국강구조학회 논문집
• /
• 제27권3호
• /
• pp.299-310
• /
• 2015

일반적인 CFT구조는 구조적 거동이 우수함에도 불구하고 폐단면으로 인한 제작 및 가공의 번거러움, 충전성 등의 문제를 가지고 있다. 이 연구는 CFT구조의 충전성을 개선한(보의 상플랜지에는 관통다이아프램, 하플랜지에는 외측다이아프램을 적용) 기둥-단순보의 접합부에서 외측 다이아프램의 치수에 따른 구조적 거동을 살펴보았다. 변수해석을 실시하여 EP-T 타입 접합부내력 영향을 주는 이유를 찾았다. 결과적으로 원형CFT기둥-보접합부에 대한 실험 및 해석을 통하여 원형 CFT구조의 구조적 거동을 조사했다.