• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 1987.04a
• /
• pp.22-26
• /
• 1987

Texture provides an important acurce of information about the threedicensfornarry information of visible surface particulary for stationary conccular views. To recover three dicmensinoary information, the distorging effects of pro jection must be distinguished from properties of the texture on which the distrortion acts. In this paper, we show an approximated maximum likelihood estimation method by which we find surface oriemtation of the visible surface in gaussian sphere using local analysis of the texture, In addition assuming that an orthographic projection and a circle is an image formation system and a texel(texture element)respectively we derive the surface orientation from the distribution of variation by means of orthographic pro jemction of a tangent directon which exstis regulary in the are length of a circle we present the orientation parameters of textured surface with saint and tilt and also the surface normal of the resvlted surface orimentation as needle map. This algorithm was applied to geograghic contour and synthetic textures.

• Journal of Korean Society for Quality Management
• /
• v.26 no.4
• /
• pp.293-310
• /
• 1998

In this paper, we surveyed the literature on QCC(quality control circle) and try to establish principles of activation of QCC activities in Korea. Although QCC activities in Korea, which originated from Japan, have so far made tremendous contributions to our domestic industry, many problems have also been found during the course of a, pp.ication to our industry. In this paper, we have paid much attention to the solution of the problems found during the initial stages and the a, pp.eciation of the achievements of QCC activities until now. We also suggest principles residing in the activities and propose the right direction of our QCC movement. We have made use of many known facts in our analysis and present some of them as evidences of our arguments.

• Proceedings of the Korea Port Economic Association Conference
• /
• 2007.07a
• /
• pp.441-455
• /
• 2007

Based on the fact that Qingdao port, Tianjin port and Dalian port of the economic circle around Bohai have been the three islands of stability through long-term competition, this paper conducts a system study on the competitive powers of the three ports through AHP model on the analysis of current status of the three ports, and probes deeply into the outer factors and the inner factors affecting on the competitive advantage, and points out the existing problems in competition. We think that the three ports must compete orderly and collaborate closely, and give the forms and approaches developing strategy collaboration in order to obtain an advantageous position in Northeast Asia and improve the international competitive power.

• Journal of the korean Society of Automotive Engineers
• /
• v.15 no.2
• /
• pp.121-129
• /
• 1993

Plane strain punch stretching test (PSST) was developed to evaluate stamping formability of sheet materials. In this test, the rectangular specimen of sheet material is uniformly stretched up to fracture by raising a specially designed punch to certainly assure plane strain stretching deformation along the longitudinal direction of the specimen. The stamping formability was evaluated by limit punch height(LPH) in plane strain punch stretching test compared to limit dome height(LDH) in hemispherical punch stretching test. LPH-value in PSST well ranks the stamping formability of various material and correlates with press performance. Moreover by using ultrasonic thickness gauge the plane strain intercept-limit plane strain(FLCo)-in forming limit curve can be accurately determined from thickness measurement around the fracture area. The FLCo derived from thickness measurement well correlates with the results from circle grid analysis for the deformed circle grid marked on the surface of the specimen.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.930-937
• /
• 2008

From the result of precise field investigation and stability analysis for the cut slope, following results were acquired. 1. The cause of the collapse of cut slope came from circle sliding collapse by fault zone which remained inner weathering zone. 2. The existing destructed soil and rock can be removed by reinforcement. And to prevent the additional destruction, it is judged that applying the method after relaxing the slope would be reasonable. 3. To make cut slope stable, soft rock layer should be done cutting 1:1.5 and 1:2.0 ~ 1:2.5 for weathered rock and soil layer. 4. Heavy water leakage section should be applied horizontal drain method so that water pressure should not act to the cut slope.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.7
• /
• pp.801-810
• /
• 1999

The purpose of present research was to get characteristics and basic knowledges of electrorheological(ER) suspension. To observe behaviors of the ER suspensions. transparent conductive plates were used to visualize the flow of ER suspensions between two parallel plate electrodes. The influence of flowing speed and intensity of electric field on the ER fluid were examined in circle-shaped electric field, and it takes several hundred milliseconds that suspensions in flow cluster. The present study also conducts a numerical analysis adopting the Bingham model. It is found that simple Bingham model can not property describe the flow behavior in the parallel plates.

• Journal of Industrial Technology
• /
• v.31 no.A
• /
• pp.11-19
• /
• 2011

A new PCD (Pitch Circle Diameter) adjustment system has been designed in this study. Traditional system requires repetitive same works in changing automobile tires. The system proposed in this study requires just one simultaneous work to finish the job. We designed the system using Solidworks CAD software. We further investigate the jobs for both cases through work factor method. Based on careful clarification of the job, work factor units were assigned to each work factor. Even if further analysis should be processed for actual field application, the mechanism proposed in this study may provide good reference for practical usage.

• Current Optics and Photonics
• /
• v.5 no.6
• /
• pp.660-671
• /
• 2021

We present a novel optical system for an augmented reality head-up display (AR HUD) with two virtual images at different conjugates by employing a confocal off-axis two-mirror and introducing the horopter circle. For a far virtual image with large asymmetrical aberrations, we initially obtain an off-axis two-mirror system corrected for these aberrations and compensated for the down angle by configuring its parameters to satisfy the confocal and Scheimpflug conditions, respectively. In addition, this system is designed to reduce the biocular parallax by matching Petzval surface into the longitudinal horopter circle in a near virtual image. This design approach enables us to easily balance the residual aberrations and biocular parallax when configuring the optical system with two different conjugates, which results in an AR HUD available for near and far virtual images together.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.53-54
• /
• 2010

This study investigates stress analysis in nodal zone by using Complementary Pole Method (CPM). The CPM is convenient tools for the stress or strain analysis since it enables to express parallel directions of the normal stress or strain on the Mohr Circle. In this study, it is suggested to use of CPM to analysis stress or strain in the field of Concrete Plasticity.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.147-148
• /
• 2012