• Membrane Journal
• /
• v.24 no.2
• /
• pp.151-157
• /
• 2014

In this study, the nanofiber composite membrane was prepared by electrospinning method with poly (ancrylonitrile) (PAN) and a dispersed solution of graphene oxide (GO) and $Fe_3O_4$ functionalized graphene oxide (M-GO) in dimethyl formamide (DMF). The pore-diameter of prepared membranes was controlled by change of those layers. It was confirmed with SEM that the nanofiber composite membranes having fiber size of 500 nm were prepared. It was found with Raman spectroscopy and EDS that GO and M-GO were well dispersed on those membranes. Final nanofiber composite membrane showed the similar pore properties ($0.21{\sim}0.24{\mu}m$/pore-size, 40% porosity) with the commercial membrane ($0.27{\mu}m$/pore-size, 55% porosity) and their water-flux results also showed the 200% higher flux than its PAN membrane. From these results, it was expected that the nanofiber composite membrane prepared by electrospinning method could be utilized as a water-treatment membrane.

• The Korean Journal of Pesticide Science
• /
• v.12 no.2
• /
• pp.127-133
• /
• 2008

The foliar uptake of dimethomorph into cucumber was assessed by spray application of aqueous dimethomorph solution containing fatty alcohol ethoxylate (FAE) or fatty acid alkyl ester as activator adjuvants. Afterward, the possible mechanism of action of FAE on foliar penetration of active ingredient was suggested by speculating on the effect of lipophile and hydrophile of FAEs. The amount of absorbed dimethomorph induced by polyoxyethylene mono-9-octadecenyl ether (6 moles ethylene oxide, $C_{18=9}E_6$) was linearly related to the concentrations of surfactant as well as dimethomorph in spray solution, suggesting that it is simply a diffusion phenomenon of the solute molecule through a cuticular membrane from leaf surface. Octadecanol attached to FAE was most effective lipophile on the leaf penetration of dimethomorph. And, the more ethylene oxide had the polyoxyethylene chain of FAE up to 20 moles, the higher the uptake rate was. Therefore, the role of lipophile of FAE on dimethomorph penetration to cucumber leaf, probably, is to modify the physico-chemical properties of cuticular membrane to be permeable to dimethomorph, and the polyoxyethylene chain having less than 20 moles ethylene oxide, which is moderately permeable to cuticular membrane by its molar volume, is to let the physically-modified cuticular membrane to be maintained for a longtime.

• Clean Technology
• /
• v.26 no.4
• /
• pp.304-310
• /
• 2020

In order to apply a photocatalyst (TiO2) to various building materials, TiO2-mayenite was prepared in this study. The TiO2 was synthesized using the sol-gel method by fixing titanium isopropoxide (TTIP) and urea at a ratio of 1 : 1. Later, they were calcined in a temperature range of 400-700 ℃ to analyze the properties according to temperature. BET, TGA, and XRD were used to analyze the physical and chemical properties of TiO2. The nitrogen oxide removal test was confirmed by measuring the change in the concentration of NO for 1 h according to KS L ISO 22197-1. The prepared TiO2 samples exhibited an anatase crystal structure below 600 ℃, and TiO2 (urea)-400 showed the highest nitrogen oxide removal rate at 2.35 µmol h-1. TiO2-mayenite was prepared using two methods: spraying TiO2 dispersion solution (s/s) and sol-gel solution (g/s). Through BET and XRD analysis, it was found that 5-TiO2 (g/s) prepared by spraying a sol-gel solution has maintained its crystallinity even after heat treatment. Also, 5-TiO2 (g/s)-500 showed the highest removal rate of 0.55 µmol h-1 in the nitrogen oxide removal test. To prepare TiO2-mayenite, it was confirmed that mayenite should be blended with TiO2 in a sol-gel state to maintain the crystal structure and exhibit a high nitrogen oxide removal rate.

• Applied Chemistry for Engineering
• /
• v.24 no.4
• /
• pp.433-437
• /
• 2013

Electrical discharge plasma created in a multi-channel porous ceramic membrane-supported catalyst was applied to the decomposition of a volatile organic compound (VOC). For the purpose of improving the oxidation capability, the ceramic membrane used as a low-pressure drop catalyst support was loaded with zinc oxide photocatalyst by the incipient wetness impregnation method. Alternating current-driven discharge plasma was created inside the porous ceramic membrane to produce reactive species such as radicals, ozone, ions and excited molecules available for the decomposition of VOC. As the voltage supplied to the reactor increased, the plasma discharge gradually propagated in the radial direction, creating an uniform plasma in the entire ceramic membrane above a certain voltage. Ethylene was used as a model VOC. The ethylene decomposition efficiency was examined with experimental variables such as the specific energy density, inlet ethylene concentration and zinc oxide loading. When compared at the identical energy density, the decomposition efficiency obtained with the zinc oxide-loaded ceramic membrane was substantially higher than that of the bare membrane case. Both nitrogen and oxygen played an important role in initiating the decomposition of ethylene. The rate of the decomposition is governed by the quantity of reactive species generated by the plasma, and a strong dependence of the decomposition efficiency on the initial concentration was observed.

• Clean Technology
• /
• v.28 no.4
• /
• pp.285-292
• /
• 2022

Adsorption tower systems based on activated carbon adsorption towers have mainly been employed to reduce the emission of volatile organic compounds (VOCs), a major cause of air pollution. However, the activated carbon currently used in these systems has a short lifespan and thus requires frequent replacement. An approach to overcome this shortcoming could be to develop metal oxide photocatalysis-activated carbon composites capable of degrading VOCs by simultaneously utilizing photocatalytic activation and powerful adsorption by activated carbon. TiO₂ has primarily been used as a metal oxide photocatalyst, but it has low economic efficiency due to its high cost. In this study, ZnO particles were synthesized as a photocatalyst due to their relatively low cost. Silver nanoparticles (Ag NPs) were deposited on the ZnO surface to compensate for the photocatalytic deactivation that arises from the wide band gap of ZnO. A microfluidic process was used to synthesize ZnO particles and Ag NPs in separate reactors and the solutions were continuously supplied with a pack bed reactor loaded with activated carbon powder. This microfluidic-assisted pack bed reactor efficiently prepared a Ag-ZnO-activated carbon composite for VOC removal. Analysis confirmed that Ag-ZnO photocatalytic particles were successfully deposited on the surface of the activated carbon. Conducting a toluene gasbag test and adsorption breakpoint test demonstrated that the composite had a more efficient removal performance than pure activated carbon. The process proposed in this study efficiently produces photocatalysis-activated carbon composites and may offer the potential for scalable production of VOC removal composites.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2007.06a
• /
• pp.251-251
• /
• 2007

• Bulletin of the Korean Chemical Society
• /
• v.32 no.9
• /
• pp.3274-3280
• /
• 2011

Monodispersed porous NiO and $Co_3O_4$ microcapsules with a hollow core were synthesized using SBA-16 silica sol and PS as a hard template. The porous hollow microcapsules were characterized by XRD, TEM and $N_2$ adsorption/desorption analysis. After $H_2$ reduction of metal oxide microspheres, they were conducted as an active catalyst in the reduction of chiral butylronitrile and cyanobenzene. The mesoporous metals having a hollow structure showed a higher activity than a nonporous metal powder and an impregnated metal on the carbon support.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.739-742
• /
• 2000

Micro machining technology has been studied to fabricate small size and high accuracy milli-structure products. To perfectly overcome the conventional mechanical machining methods, the chemical mechanical micro machining(C3M) process was developed. The mechanism of C3M process is that chemical solution etches the material and results in the generation of the chemical reacted layer, and the mechanical micro tool subsequently removes the layer. From the fundamental experiments, the C3M process has been founded to have the advantages of lower machining resistance, tool wear, and higher surface quality and form accuracy than conventional methods. This study focuses on the micro grooving of both the metallic material(SKDII, A1) and hard brittle silicon oxide.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.5
• /
• pp.1131-1134
• /
• 2009

Preparation of graded materials displaying gradients of desired properties is one of the important issues and less-developed areas in materials chemistry. For the first time we demonstrate facile control of porosity and length in the pores of AAO template in lateral directions by controlled dipping method. To demonstrate the versatility of the proposed method, laterally graded silica nanotubes are also prepared by using the laterally graded AAO templates. The method demonstrated here will open numerous possibilities for obtaining a variety of graded materials with lateral gradients of catalytic, electrochemical, mechanical and optical properties on the nanoscale.

• Applied Chemistry for Engineering
• /
• v.9 no.7
• /
• pp.990-997
• /
• 1998

In this work, the $SiO_2$ films on the silicon substrate with different orientations were first prepared by the low temperature process using the ECR plasma diffusion as a function of microwave power and oxidation time. Before and after thermal treatment, the surface morphology, Si/O ratio from physicochemical properties, and the electrical properties of the oxide films were also investigated. The oxidation rate increased with microwave power, while surface morphology showed the nonuniform due to etching. The film quality, therefore, was lowered with increasing the defect by etching and the content of positive oxide ions in the oxide films from bulk by higher self-DC bias. The content of positive oxide ions in the oxide films with different Si orientations showed Si(100) < Si(111) < poly Si. The defects in $Si/SiO_2$ interface of $SiO_2$ film could be decreased by annealing, while $Q_{it}$ and $Q_f$ were independent of thermal treatment and the dependent on concentration of reactive oxide ions and self-DC bias of substrate. At microwave power of 300, and 400 W, the high quality $SiO_2$ film that had lower surface roughness and defect in $Si/SiO_2$ interface was obtained. The value of interface trap density, then, was ${\sim}9{\times}10^{10}cm^{-2}eV^{-1}$.