• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.23 no.3
• /
• pp.273-278
• /
• 2014

This study presents a chatter vibration avoidance program for the milling process. Chatter vibration has a negative effect on workpieces and spindle-tools. When chatter vibration occurs, the cutting tool is loaded dynamically, a chatter pattern is generated on the workpiece, and the tool life is reduced. The developed program is composed of various modules such as an FFT analyzer, an impact test analyzer, a chatter vibration indicator, and a spindle speed recommender. The proposed program is verified using an AISI D2 cutting experiment in milling process. The effect of chatter vibration on the machining condition can be simulated by the suggested method, and successfully exploited to avoid chatter vibration.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.28-32
• /
• 1995

Bacause the chatter vibration is a main factor to damage on the quality and integrity, The cure is required peticurity in cykinderical plunge grinding. The chatter vibration relatied with wheel speed, workpiece and infeed rate. Therefore, we expressed more credible normal signal and chatter signal Pattern in accrdiance with wheel speed and acquired RMS signal of the accelerrometer. In thos study, after finding the chatter pattern, we applied two parameters, standard deviation and Kurtosis, to Neural Network.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.77-82
• /
• 2004

There were many researches about the chatter vibration occur in the cutting process of machine tools. But there are in sufficient research parts ; the frequency about the chatter vibration and its characteristics and its nonlinear properties. This paper measured signals of vibration that occur before and immediately after and after the chatter vibration. This signals were analyzed through autospectrum obtained by the Fast Fourier Transform(FFT). And then, the nonlinear characteristis were analyzed by cepstrum analysis through FFT of autospectrun.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.745-750
• /
• 2014

The chatter vibration in the machining process plays bad role in machining quality such as high roughness as well as tool life and machine failure. And the grinding process under this risk in the fully automated factory is exposed to the unexpected mass machining quality problem. Studying the vibration signal of the hub bearing grinding process, the reason of chatter vibration was explained with the specific machining pattern of chatter. And this study suggests the chatter detecting method in the production line, which is monitoring the peak acceleration level around the natural frequencies of the specimen, and calculating kurtosis value by assuming the chatter is related to the resonance of the specimen. The suggested method was applied to the vehicle hub bearing grinding process and proved good to detecting the chatter induced machining quality problem.

• Journal of the Korean Society for Precision Engineering
• /
• v.8 no.3
• /
• pp.73-81
• /
• 1991

There have been many studies on chatter vibration in machining but there seems to be no regulations to decide the commencing point of chatter objectively. The development of an objective method which can estimate and detect chatter commencement is very much in need for automatic manufacturing systems, dynamic performance tests for machine tools, so on. In this study, therefore, the estimation and the in-process detection of chatter have been experi- mentally investigated for the turning process. As a result, the commencing point of chatter can be decided from the behavior of the maximum amplitude of the dynamic component of cutting force, where the maximum amplitude is suddenly increasing with the chatter commencement. Then the commencing point of chatter can be estimated practically by this method before the occurrence of excessive vibration. Also, it is possible to detect the occurence of chatter vibration through the in-process measurement, by monitoring the maximum amplitude of the dynamic component of cutting force.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.2
• /
• pp.48-61
• /
• 1996

In the hot strip mill, not only the chatter vibration of finishing stands has a great influence on the surface quality of hot products, but also that is the major factors to shorten the life of rolling mill housings or to create the machine troubles. As long as the mill has been operating, the low frequency chatter at the early mill stands (No.2 and No.3) of POSCO's Kwangyang No.2 hot strip mill had been detected when rolling certain types of products, e.g., thinner gage, hard grade products. For several years, the experimental study was undertaken to analyze the cause of the chatter vibration and establish the methods to avoid the vibration to acceptable levels. The analysis and solution to the vibration problem with recommendations and revised maintenance practice are the subjects of this article.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.977-981
• /
• 1997

Because the chatter vibration is a main factor to damage on the quality, The cure is require peticually in cylinderical plunge grinding. The chatter vibration is with wheel speed, workpiece speed and infreed rate. Therefore, in this study, we expressed more credible chatter frequency in accordiance with wheel speed by FFT after accereleration sensing.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.1
• /
• pp.9-16
• /
• 2015

The machining-chatter stands for a sudden relative vibration appeared between a material and a tool while processing with a machine. This chatter is key factor that seriously affects the quality of processed materials as well as being a factor which causes serious damages to the tool and the machine. This study is related to the monitoring and smart control of chatter problem that can compensate machining-chatter faster and produce processed goods with more precision by autonomous compensation. The above-mentioned machining-chatter compensator includes the chatter vibration sensor and the chatter compensator that estimates the compensation value according to the sensor detecting the chatter vibration of machine-tool and the chatter vibration detected from the sensor while having a feature of being organized by interlocking with the machine-tool controller.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.28-33
• /
• 2000

The monitoring of the chatter vibration is necessarily required to do automatic manufacturing system. To this study, we constructed a sensing system using tool dynamometer in order to the chatter vibration on cutting process. And a approach to a neural network using the feature of principal cutting force signals is proposed. with the error back propagation training process, the neural network memorized and classified the feature of principal cutting force signals. As a result, it is shown by neural network that the chatter vibration can be monitored effectively.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.10
• /
• pp.50-56
• /
• 1995

Chatter Vibration is an unwanted phenomenon in metal cutting and it always affects surface finish, tool life, machine life and the productivity of machining process. The real-time detection of the chatter vibration is is necessarily required to automation system. In this study, we constructed the multi-sensing system using Tool Dynamometer, Accelermeter and AE sensor. Especially, Acoustic Emission(AE) generated during turning was investigated the possibility for real-time detection of chatter vibration. Turning experiments were performed using carbide insert tip under realistic cutting conditions and tapered workpiece of SM45C. Consquently, the real-time detection using multi-sensing system can be used for Inprocess monitoring of chatter vibration.