• Journal of Welding and Joining
• /
• v.3 no.2
• /
• pp.1-9
• /
• 1985

In this study, the influence of carbon equivalents on friction welds of similar steels was investigated. Four types of steels with 15mm diameter tested in the wide range of carbon equivalents from 0.3 to 1.1 Main experimental results are summarized as follows : (1) Under the constant burn-off length, the friction time becomes longer with the increasing carbon equivalent, but the upset length shows no consistent tendencies. (2) Due to the recrystallization in the contact area, the maximum hardness occurs some away from the contact surface. And it increases almost linearly with the increasing carbon equivalent. (3) Even a steel with 1.1 C.E. can be friction welded to make defect-free welds. (4) With the increasing carbon equivalent, the bend angle and charpy impact value decrease very rapidly in the range from 0.3 C. E., but remain nearly unchanged for C. E. higher than 0.6. (5) Heat treatment of the base metals before welding has very little influence on the mechanical properties of welds. On the other hand, normalizing of the welds improves the bend angle and charpy impact value, but its effect becomes almost negligible, when the carbon equivalents are higher than 0.6.

• Journal of Welding and Joining
• /
• v.33 no.1
• /
• pp.72-79
• /
• 2015

Evaluation of fracture toughness of welded structures has a significant influence on the structural design. However the residual stresses is redistributed while the welded structures is cut for preparing specimens. This study investigated an effect of the welding residual stress redistribution on the impact absorption energy of Charpy specimen. SA516Gr70 steel plate by at the flux cored arc welding (FCAW) and gas tungsten arc welding(GTAW) was cutting. Specimens for Charpy impact testing were taken from the welded plate. Two material removal mechanisms (wire cutting and water jet) were used to make the specimens. Welding residual stress and redistribution residual stress were measured using the XRD (X-Ray Diffraction) method. The amount of redistribution of residual stress depends on the different material removal mechanism. Redistribution of residual stress of reduced the impact absorption energy by 15%.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.138-140
• /
• 2007

This study aimed to evaluate the low temperature properties of the 18Cr ferritic stainless steel weld. Applied welding methods were LB(Laser Beam) and GTA(Gas Tungsten Arc) welding to compare the different low temperature properties of the welds. Low temperature properties were evaluated by the Charpy impact, Erichsen and Expansion test at low temperature. LB weld showed superior low temperature properties in the cases of the Charpy impact test and expansion test at low temperature, while GTA weld showed a superior low temperature property in the case of Erichsen test at low temperature. The different low temperature properties with test methods are still under analysis and may be due to different crack path depending on the microstructure, test speed and stress concentration during test.

• Nuclear Engineering and Technology
• /
• v.30 no.4
• /
• pp.364-376
• /
• 1998

The statistical analysis method was applied to the evaluation of fracture toughness in the ductile-brittle transition temperature region. Because cleavage fracture in steel is of a statistical nature, fracture toughness data or values show a similar statistical trend. Using the three-parameter Weibull distribution, a fracture toughness vs. temperature curve (K-curve) was directly generated from a set of fracture toughness data at a selected temperature. Charpy V-notch impact energy was also used to obtain the K-curve by a $K_{IC}$ -CVN (Charpy V-notch energy) correlation. Furthermore, this method was applied to evaluate the neutron irradiation embrittlement of reactor pressure vessel (RPV) steel. Most of the fracture toughness data were within the 95% confidence limits. The prediction of a transition temperature shift by statistical analysis was compared with that from the experimental data.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.96-101
• /
• 2004

Cast austenitic stainless steel is used for several components, such as primary coolant piping, elbow, pump casing and valve bodies in light water reactors. These components are subject to thermal embrittlement at the reactor operating temperature. The objective of this study is to summarize the method of estimating ferrite content, Charpy impact energy and J-R curve and to evaluate the thermal embrittlement of the cast austenitic stainless steel piping used in the domestic nuclear power plants. The result of evaluation, two domestic nuclear power plants used CF-8M and CF-8A material has adequate fracture toughness after saturation.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.5 no.3
• /
• pp.1-9
• /
• 2001

Impact tests are performed on the high strength structural steel that is being developed for the submarine material. Especially, the impact characteristics of this structural steels at low temperatures are investigated by charpy impact testing. Hyperbolic tangent curve fitting method is used to evaluate the LSE(lower shelf energy), USE(upper shelf energy) and DBTT(ductile-brittle transition temperature). Proportional equations between charpy impact energy and lateral expansion are obtained using the test results. Effect of temperature on the fracture appearance is investigated by using SEM.

• Steel and Composite Structures
• /
• v.17 no.5
• /
• pp.549-560
• /
• 2014

The paper provides the test results and analysis on the behavior of steel 1.7147 at different temperatures. Mechanical uniaxial tests were used to determine mechanical properties, resistance to creep and Charpy impact tests to determine impact energy. Test results are presented in the form of engineering stress-strain diagrams, creep curves as well as numerical data related to impact energy. The results show that the tensile strength has the highest value at room temperature, and the same goes for the yield strength as well as for modulus of elasticity. After room temperature both of mentioned properties decrease with temperature increasing. Some of creep curves were modeled using rheological models and analytical equation. Based on Charpy impact energy an assessment of fracture toughness was made.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2005.10a
• /
• pp.358-359
• /
• 2005

• Proceedings of the KWS Conference
• /
• 2001.10a
• /
• pp.247-251
• /
• 2001

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.1
• /
• pp.93-103
• /
• 1997

Charpy V-notch impact tests were performed on the full-, half-and third-size specimens from two ferritic SA 508 Cl. 3 steels for nuclear pressure vessel. New normalization factors were proposed to predict the upper shelf energy(USE) and the ductile-brittle transition temperature(DBTT) of full-size specimens from the measured data on sub-size specimens. The factors for the USE and the DBTT are $(Bb^2/Kt); and; (Bb/R)^1/2/, $ respectively, where B the width, b the ligament size, $K_{t}$ the elastic stress concentration factor, and R the notch root radius. These correlations successfully estimated the USE and DBTT of the full-size specimens based on sub-size specimen data. In addition, the size effects were studied to develop the correlations among absorbed energy, lateral expansion(LE) and displacement. It was also found that the LE was able to be estimated from the displacement obtained by the instrumented impact test, and that the displacement would be used as a criterion for the toughness of the steels corresponding to change in their yield strength.h.