1 |
Brnic, J., Canadija, M., Turkalj, G. and Lanc, D. (2010b), "Structural steel ASTM A709-behavior at uniaxial tests conducted at lowered and elevated temperatures, short-time creep response, and fracture toughness calculation", J. Eng. Mech., 136(9), 1083-1089.
DOI
|
2 |
Bomas, H., Burkart, K. and Zoch, H.W. (2012), "VHCF behaviour of case-hardened specimens made of two grades of steel SAE 5120 differing in microstructure", Int. J. Fatigue, 60, 63-73.
|
3 |
Boresi, A.P. and Schmidt, R.J. (2003), Advanced Mechanics of Materials, John Wiley & Sons, USA.
|
4 |
Brnic, J., Canadija, M., Turkalj, G. and Lanc, D. (2010a), "50CrMo4 steel-determination of mechanical properties at lowered and elevated temperatures, creep behavior and fracture toughness calculation", J. Eng. Mater. Techn., 132(2), 021004.
DOI
ScienceOn
|
5 |
Brnic, J., Turkalj, G., Canadija, M. and Lanc, D. (2011a), "AISI 316Ti (1.4571) steel - Mechanical, creep and fracture properties versus temperature", J. Construct. Steel Res., 67(12), 1948-1952.
DOI
|
6 |
Brnic, J., Turkalj, G., Canadija, M., Lanc, D. and Krscanski, S. (2011b), "Martensitic stainless steel AISI 420 - Mechanical properties, creep and fracture toughness", Mech. Time-depend. Mater., 15(4), 341-352.
DOI
|
7 |
Brnic, J., Turkalj, G., Vukelic, G. and Brcic, M. (2012), "Analysis of the dependence of material properties on temperature - Steel 1.4122" , High Temp. Mater. Proc., 31(3), 259-266.
|
8 |
Brnic, J., Turkalj, G., Niu, J., Canadija, M. and Lanc, D. (2013), "Analysis of experimental data on the behavior of steel S275JR - Reliability of modern design", Mater. Des., 47, 497-504.
DOI
|
9 |
Collins, J.A. (1993), Failure of Materials in Mechanical Design, John Wiley & Sons, New York, USA.
|
10 |
Conrado, E., Foletti, S., Gorla, C. and Papadopoulos, I.V. (2011), "Use of multiaxial fatigue criteria and shakedown theorems in thermo-elastic rolling-sliding contact problems", Wear, 270(5-6), 344-354.
DOI
|
11 |
Martins, R.C., Seabra, J.H.O. and Ruis-Moron, L.F. (2011), "Influence of oil formulation on gear micropitting and power loss performance", Proceedings of the Institution of Mechanical Engineers, Part J: J. Eng. Tribol., 225(6), 429-439.
DOI
|
12 |
Draper, N.R. and Smith, H. (1998), Applied Regression Analysis, Wiley-Interscience Publications, USA.
|
13 |
Gross, D. and Seeling, T. (2011), Fracture Mechanics, Springer - Verlag, Berlin, Germany.
|
14 |
Klobcar, D., Kosec, L., Kosec, B. and Tusek, J. (2012), "Thermo fatigue cracking of die casting dies", Eng. Fail. Anal., 20, 43-53.
DOI
|
15 |
Milutinovic, M., Movrin, D. and Pepelnjak, T. (2012), "Theoretical and experimental investigation of cold hobbing processes in cases of cone-like punch manufacturing", Int. J. Adv. Manuf. Tech., 58(9-12), 895-906.
DOI
|
16 |
Shekhter, A., Kim, S., Carr, D.G., Crocker, A.B.L. and Ringer, S.P. (2002), "Assessment of temper embrittlement in an ex-service 1Cr-1Mo-0.25V power generating rotor by Charpy V-notch testing; KIc fracture toughness and small punch test", Int. J. Press. Vessels Pip., 79(8-10), 611-615.
DOI
|
17 |
Roberts, R. and Newton, C. (1981), Interpretive Report on Small Scale Test Correlation with KIc Data, Welding Research Council Bulletin, Volume 265, 1-18.
|
18 |
Annual Book of ASTM Standards (2012), Metal Test Methods and Analytical Procedures, Vol. 03.01, ASTM International, Baltimore, MD, USA.
|
19 |
Raghavan, V. (2004), Materials Science and Engineering, Prentice- Hall of India, New Delhi, India.
|
20 |
Rao, S.S. (2009), Engineering Optimization, John Wiley & Sons, NJ, USa.
|
21 |
Yu, Z.W., Xu, X.L., Yang, Z. and Li, Y.Y. (2012), "Case internal oxidation and intergranular fracture of carburized splined-shaft", Eng. Fail. Anal., 22, 141-151.
DOI
|
22 |
Pepelnjak, T., Petek, A. and Kuzman, K. (2005), "Analysis of the forming limit diagram in digital environment", Adv. Mater. Res., 6-8, 697-704.
DOI
|
23 |
Plaseied, A. and Fatemi, A. (2008), "Deformation response and constitutive modeling of vinyl ester polymer including strain rate and temperature effects", J. Mater. Sci., 43(4), 1191-1199.
DOI
|
24 |
Belegundu, A.D. and Chandrpatla, T.R. (2011), Optimization Concept and Application in Engineering, Cambridge University Press, New York, USA.
|
25 |
Ahlroos, T., Ronkainen, H., Helle, A., Parikka, R., Virta, J. and Varjus, S. (2009), "Twin disc micropitting tests", Tribol. Int., 42(10), 1460-1466.
DOI
|
26 |
Anderson, T.L. (1995), Fracture Mechanics, CRC Press, New York.
|
27 |
Shijve, J. (2009), Fatigue of Structures and Materials, Springer Science & Business Media, Delft, Netherlands.
|