• Proceedings of the KSRS Conference
• /
• 2007.10a
• /
• pp.464-467
• /
• 2007

All image data acquisition systems for example the digital camera and digital camcorder, use the image sensor to convert the image data (light) into electronic data. These image sensors are used in satellite camera for high quality and resolution image data. There are two kinds of image sensors, the one is the CCD (charge coupled device) detector sensor and the other is the CMOS (complementary metal-oxide semiconductor) image sensor. The CCD sensor control system has more complex than the CMOS sensor control system. For the high quality image data on CCD sensor, the precise timing control signal and the several voltage sources are needed in the control system. In this paper, the comparison of the CCD with CMOS sensor, the CCD sensor characteristic, and the control system will be described.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.1118-1120
• /
• 2003

In MSC(Multi-spectral camera ), the incoming light is converted to electronic analog signals by the CCD(charge coupled device) detectors. The analog signals are amplified, biased and converted into digital signals (pixel data stream) in the FPE(Focal plane electronics ). The digital data is transmitted to the PMU for pre-processing to correct for nonuniformity, to partially reorder the pixel stream and to add header data for identification and synchronization In this paper, the video data streams is described in terms of hardware.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.529-532
• /
• 2004

The spatio-temporal variation of Infra Red(IR) emission images were obtained from a real 3-dimensional discharge space of a surface discharge type, alternating current plasma display panel(AC PDP) cell with the Ne-Xe(4%) 400Torr gas mixture. IR emissions were observed in each period of the ADS(Address and Display Separation) driving scheme with ramp initializing waveform using an images intensified charge coupled device(ICCD) camera. The roles of each electrode were identified and it was compared with the results of the discharge simulation and of the wall charge distributions measured by the electro-optic technique.

• Journal of Radiation Protection and Research
• /
• v.39 no.3
• /
• pp.150-158
• /
• 2014

Radiation-related practitioners and radiation-treated patients at medical institutions are inevitably exposed to radiation for diagnosis and treatment. Although standards for maximum doses are recommended by the International Commission on Radiological Protection (ICPR) and the International Atomic Energy Agency (IAEA), more direct and available measurement and analytical methods are necessary for optimal exposure management for potential exposure subjects such as practitioners and patients. Thus, in this study we developed a system for real-time radiation monitoring at a distance that works with existing portable device. The monitoring system comprises three parts for detection, imaging, and transmission. For miniaturization of the detection part, a scintillation detector was designed based on a silicon photomultiplier (SiPM). The imaging part uses a wireless charge-coupled device (CCD) camera module along with the detection part to transmit a radiation image and measured data through the transmission part using a Bluetooth-enabled portable device. To evaluate the performance of the developed system, diagnostic X-ray generators and sources of $^{137}Cs$, $^{22}Na$, $^{60}Co$, $^{204}Tl$, and $^{90}Sr$ were used. We checked the results for reactivity to gamma, beta, and X-ray radiation and determined that the error range in the response linearity is less than 3% with regard to radiation strength and in the detection accuracy evaluation with regard to measured distance using MCNPX Code. We hope that the results of this study will contribute to cost savings for radiation detection system configuration and to individual exposure management.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.2
• /
• pp.112-119
• /
• 2011

This paper is concerned with the measurement of static and dynamic displacement by image processing(IP) and study for prediction method of velocity and acceleration. To measure the displacement visually, the measurement system consists of a telephoto zoom camera, CCD(charge coupled device) image device and a computer. The specific target on the white board is used to calculate the displacement of the structure. The captured image is then converted into a pixel-based data and then analyzed numerically. The limitation of the system depends on the image capturing speed and the pixel-size of image. In this paper, we developed for the displacement measurement using the image processing method. The proposed method enables us to measure the vibration displacement, velocity and acceleration directly without any contact. The current resolution for the displacement measurement can be seen from the results.

• Proceedings of the KSRS Conference
• /
• v.2
• /
• pp.797-799
• /
• 2006

The Electro-optical camera subsystem as a payload of a satellite system consists of OM (optical module) and CEU(camera electronics unit), and most performances of the camera subsystem depend a lot on the CEU in which TDI CCDs(Time Delayed Integration Charge Coupled Device) take the main role of imaging by converting the light intensity into measurable voltage signal. Therefore it is required to specify and design the CEU very carefully at the early stage of development with overall specifications, design considerations, calibration definition, test methods for key performance parameters. This paper describes the overview of CEU development. It lists key requirement characteristics of CEU hardware and design considerations. It also describes what kinds of calibration are required for the CEU and defines the test and evaluation conditions in verifying requirement specifications of the CEU, which are used during acceptance test, considering the fact that CEU performance results change a lot depending on test and evaluation conditions such as operational line rate, TDI level, and light intensity level, so on.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.12 no.2
• /
• pp.173-180
• /
• 1994

One can see more and more photograrmmetric applications dealing with the extraction of information from images obtained with CCD (Charge Coupled Device) camera scanners. In order for this information to be useful, the scanning errors of scanners must be known through a calibration. Investigation of this study is given to the detailed procedure of the correction for scanning errors created during the scanning of photographs with CCD camera scanner using the three kinds of high resolution reseal plates prepared. The geometric corrected digital images for scanning errors were generated and the accuracy of the resulting new images for each types of plates were checked comparing its image coordinates with there corresponding ground coordinates for the check points.

• Korean Journal of Remote Sensing
• /
• v.19 no.1
• /
• pp.91-97
• /
• 2003

The design of Graphic Information System(GIS) in various applications is suffering from the difficulty of data acquisition, which is labor-intensive and time consuming. In order to provide the spatial data rapidly and accurately, 4S-Van, a prototype mobile mapping system, has been developed. The 4S-Van consists of 1)Global Positioning System(GPS), Inertial Navigation System(INS) for estimating the geographic position and attitude of the moving van, i.e.,(x, y, z) and the direction of the Van, 2) Charge Coupled Device(CCD) camera and laser scanner for capturing images and for measuring depth from geographic objects, and 3) External Synchronization Device(ESD) and industrial PC for synchronizing data from GPS/INS/CCD camera and for storing the data. In this paper, we present the design and implementation of the proto-Dpe 4S-Van system for spatial data acquisition for various GIS applications.

• Korean Journal of Optics and Photonics
• /
• v.13 no.2
• /
• pp.92-97
• /
• 2002

A real-time OTF (optical transfer function) measuring system with on- and off-axis nodal slide bench type for the camera lens is fabricated and evaluated. It consists of a nodal slide bench including a T-bar for the OTF measurement of an off-axis object, two dimensional CCD (charge coupled device) with pixel of 9.9${\mu}{\textrm}{m}$$\times$9.6${\mu}{\textrm}{m}$ for real-time OTF measurment, and a collimating lens of focal length of 300 mm for the optimization of this system. The OTF system is corrected by using the OTF of a SIRA lens of fnumber of F/8 and focal length 50 mm. In order to confirm the reliability of the OTF system, two MTFs (modulus transfer functions) of CCTV & VIDEO lens (JAPAN, AVENIR-SE 2514) of focal length of 25mm and field of view 10.6$^{\circ}$are measured by the camera bench type OTF system of reference OTF system and the nodal slide bench type OTF system and compared with each other. As a result, these two values are agree well with each other within 4% from 0 1p/mm to 100 1p/mm.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.2
• /
• pp.261-269
• /
• 2018

This paper presents a convenient method to estimate the internal parameters of plenoptic camera using CCD(charge-coupled device) camera model. The images used for plenoptic camera calibration generally use the checkerboard pattern used in CCD camera calibration. Based on the CCD camera model, the determinant of the plenoptic camera model can be derived through the relationship with the plenoptic camera model. We formulate four equations that express the focal length, the principal point, the baseline, and distance between the virtual camera and the object. By performing a nonlinear optimization technique, we solve the equations to estimate the parameters. We compare the estimation results with the actual parameters and evaluate the reprojection error. Experimental results show that the MSE(mean square error) is 0.309 and estimation values are very close to actual values.