• Journal of the Korean Recycled Construction Resources Institute
• /
• v.1 no.3
• /
• pp.219-224
• /
• 2013

In this study, the inorganic insulating material was fabricated with quartzite, ordinary portland cement(OPC), lime and anhydrous gypsum. After characteristic analysis of slurry, the optimum mixing ratio was derived with different $CaO/SiO_2$ mole ratio. Based on derived mixing ratio, the inorganic insulating material was fabricated at different water content and hydrothermal synthesis conditions. Specific gravity was $0.26g/cm^3$, compressive strength was 0.4 MPa, and thermal conductivity was 0.064 W/mK. This properties were enhanced performance of conventional ALC (Autoclaved Lightweight Concrete). And it can replace organic insulation with harmless inorganic insulation through continues research and development.

• Journal of the Korean Ceramic Society
• /
• v.44 no.7
• /
• pp.362-367
• /
• 2007

Stent is a tiny structure made with either ceramic coating and/or bare metal. Being approximately $1{\sim}2 mm$ in diameter, it consists of holes, slots, or void space and is designed to cover entire medical lesions. Stent implantation into patients' arteries has been practiced for a little more than a decade in order to widen the blocked artery. The adoption of the stent has significantly improved the efficacy when compared with the previous medical practice by balloon angioplasty alone. Yet better biomedical performance of the stent is being demanded in order to eliminate the still existing problem of artery restenosis, which means the artery becomes narrowed again. Recent literature survey shows researches on ceramic coatings onto the stent surface, or material design to improve the mechanical response of the stent. This study focuses more on the material design and mechanical analysis. The results showed that the void configuration within the stent affects the mechanical response significantly. The rectangular shape was found to yield expansion at a relatively lower pressure than the elliptical slot for a slotted tube stent. The present results, when combined with research on coating at the stent surface, may provide stents with improved bio-medical performance.

• Journal of the Korean Ceramic Society
• /
• v.39 no.10
• /
• pp.919-927
• /
• 2002

In order to fabricate double-layered porous materials powders of different particle sizes were pressed stepwise. Ford＇s equation which predicts the fired density with the change in pressed density was employed in order to adjust the difference in sintering shrinkage of the green body with double-layered porous structure. Double-layered porous materials were characterized by investigating microstructures and permeability. SEM micrographs showed the distinct difference in pore sizes of double-layered porous material. Permeability of single-layered porous material increased by increasing the starting particle sizes and porosity as well. Permeability of the double-layered porous material depends largely on the layer of small pore diameter.

• The Journal of Advanced Prosthodontics
• /
• v.12 no.2
• /
• pp.61-66
• /
• 2020

PURPOSE. The aim of the present study was to determine the degree of conversion of light- and dual-cured resin cements used in the cementation of all-ceramic restorations under different thicknesses of translucent (T) and high-translucent (HT) polymer-infiltrated ceramic-network (PICN) material. MATERIALS AND METHODS. T and HT PICN blocks were prepared at 0.5, 1.0, 1.5, and 2.0 mm thicknesses (n=80). Resin cement samples were prepared with a diameter of 6 mm and a thickness of 100 ㎛. Light-cured resin cement was polymerized for 30 seconds, and dual-cure resin cement was polymerized for 20 seconds (n=180). Fourier transform infrared spectroscopy (FTIR) was used for degree of conversion measurements. The obtained data were analyzed with ANOVA and Tukey HSD, and independent t-test. RESULTS. As a result of FTIR analysis, the degree of conversion of the light-cured resin cement prepared under 1.5- and 2.0-mm-thick T and HT ceramics was found to be lower than that of the control group. Regarding the degree of conversion of the dual-cured resin cement group, there was no significant difference from the control group. CONCLUSION. Within the limitation of present study, it can be concluded that using of dual cure resin cement can be suggested for cementation of PICN material, especially for thicknesses of 1.5 mm and above.

• Journal of the Korean Ceramic Society
• /
• v.43 no.9 s.292
• /
• pp.564-568
• /
• 2006

AlO(OH) nano gel is used in precursor of ceramic material, coating material and catalyst. For use of these, not only physiochemical control for particle morphology, pore characteristic and peptization but also studies of synthetic method for preparation of advanced application products were required. In this study, AlO(OH) nano gel was prepared through the aging and drying process of aluminum hydroxides gel precipitated by the hydrolysis reaction of dilute NaOH solution and aluminum sulfate solution. In this process, optimum synthetic condition of AlO(OH) nano gel having excellent pore volume as studying the effect of water and aluminum sulfate mole ratio on gel precipitates has been studied. Water and aluminum sulfate mole ratio brought about numerous changes on crystal morphology, surface area, pore volume and pore size. Physiochemical properties were investigated as using XRD, TEM, TG/DTA, FT-IR, and $N_2$ BET method.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.2
• /
• pp.151-157
• /
• 2023

Integrating dielectric materials into LTCC is a convenient method to increase the integration density in electronic circuits. To enable co-firing of the high-k and low-k dielectric LTCC materials in a multi-material hetero-laminate, the shrinkage characteristics of both materials should be similar. Moreover, thermal expansion mismatch between materials during co-firing should be minimized. The alternating stacking of an LTCC with silica filler and that with calcium-zirconate filler was observed to examine the use of the same glass in different LTCCs to minimize the difference in shrinkage and thermal expansion coefficient. For the LTCC of silica filler with a low dielectric constant and that of calcium zirconate filler with a high dielectric constant, the amount of shrinkage was examined through a thermomechanical analysis, and the predicted appropriate fraction of each filler was applied to green sheets by tape casting. The green sheets of different fillers were alternatingly laminated to the thickness of 500 ㎛. As a result of examining the junction, it was observed through SEM that a complete bonding was achieved by constrained sintering in the structure of 'calcium zirconate 50 vol%-silica 30 vol%-calcium zirconate 50 vol%'.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2000.04a
• /
• pp.109.2-109.2
• /
• 2000

• Journal of the Korean Ceramic Society
• /
• v.36 no.6
• /
• pp.611-617
• /
• 1999

• Korean Journal of Materials Research
• /
• v.20 no.6
• /
• pp.326-330
• /
• 2010

$CoSb_3$ Skutterudites materials have high potential for thermoelectric application at mid-temperature range because of their superior thermoelectric properties via control of charge carrier density and substitution of foreign atoms. Improvement of thermoelectric properties is expected for the ternary solid solution developed by substitution of foreign atoms having different valances into the $CoSb_3$ matrix. In this study, ternary solid solutions with a stoichiometry of $Co_{1-x}Ni_xSb_3$ x = 0.01, 0.05, 0.1, 0.2, $CoSb_{3-y}Te_y$, y = 0.1, 0.2, 0.3 were prepared by the Spark Plasma Sintering (SPS) system. Before the SPS synthesis, the ingots were synthesized by vacuum induction melting and followed by annealing. For phase analysis X-ray powder diffraction patterns were checked. All the samples were confirmed as single phase; however, with samples that were more doped than the solubility limit some secondary phases were detected. All the samples doped with Ni and Te atoms showed a negative Seebeck coefficient and their electrical conductivities increased with the doping amount up to the solubility limit. For the samples prepared by SPS the maximum value for dimensionless figure of merit reached 0.26, 0.42 for $Co_{0.9}Ni_{0.1}Sb_3$, $CoSb_{2.8}Te_{0.2}$ at 690 K, respectively. These results show that the SPS method is effective in this system and Ni/Te dopants are also effective for increasing thermoelectric properties of this system.

• Journal of the Korean Ceramic Society
• /
• v.52 no.1
• /
• pp.33-40
• /
• 2015

Onggi, described as a 'breathing' type of pottery' has significantly influenced the traditional food culture of Korea. It is known that Onggi is an optimal type of storage for fermented foods such as soy sauce, salted seafood, and Kimchi, as air or liquid can penetrate through the body of this material. These foods gain flavor due to the breeding of aerobic bacteria at the beginning of the fermentation process. In this study, Onggi materials from five regions, Gangjin, Yeoju, Ulsan, Yesan, and Jeju, were collected and analyzed to determine their chemical and physical properties before and after sintering. The differences in the raw materials of other mining regions are examined in terms of their chemical and mineralogical compositions, specific surface area, particle size, and particle distribution. Among them, the Gangjin raw material has the greatest mean particle size of $92.29{\mu}m$, as well as the widest particle size distribution. Differences in the levels of $SiO_2$ and $Fe_2O_3$ are shown among Onggi raw materials. However, the crystalline phases formed after sintering are identical, except for the Jeju samples. At all sintering temperatures tested here, Gangjin Onggi showed the greatest porosity, leading to complete air permeation through the body within 90 minutes. These results taken together indicate that air permeation is strongly related to the pore structures in the Onggi body. This is assumed to affect the fermentation behavior.