• 한국안전학회지
• /
• 제14권4호
• /
• pp.78-84
• /
• 1999

A compact air-preheating type heat exchanger was developed and tested for the ultra-high temperature heat recovery applications. For the direct use of exhaust gases up to $1200^{\circ}C$, the heat exchanger adopted a ceramic core with high strength and low thermal expansion coefficient less than $1{\times}10^{-6}^{\circ}C^{-1}$. The ceramic core was fabricated by special extrusion and bonding techniques. To minimize thermal stresses in the core, spring-loaded sealing mechanism was designed and successfully installed. 1-pass air flow scheme was adopted for the compactness and cost-savings. The pressure test for the ceramic core showed no failure under 35 kPa and less than 3% leak under 7 kPa. Flue gas simulation system was developed to investigate the performance of the heat exchanger. The test results showed normal operations of the heat exchanger up to $1200^{\circ}C$ of exhaust gases and relatively high heat recovery efficiencies of 31～39% depending upon exhaust gas temperatures..

• 대한치과보철학회지
• /
• 제43권5호
• /
• pp.587-598
• /
• 2005

Statement of problem: Ceramic restorations should be made of porcelain layers of different opacity, shade, and thickness in order to provide a natural appearance. Lithium disilicate glass-ceramic system has superior color reproducibility, because it uses the ceramic ingot which is similar to teeth shade and uses the staining technique and layering technique. However, staining technique has a fault of discoloration. Also, porcelain is divided core and dentin layer, it is not enough to study about the influence of porcelain layer thickness and shade on the shade of ceramic restorations. Purpose: The purpose of this study was to evaluate the influence of porcelain layer thickness and color on the final shade of ceramic restorations. Materials and method: The CIE $L^*a^*b^*$(CIELAB) values of 72 assembled specimens, each consisting of 3 discs (enamel porcelain 0.2 mm/dentin porcelain -1.2, 0.9, 0.7, 0.5 or 0.3 mm/ceramic core -0.3, 0.5, 0.7, 0.9 or 1.2 mm, diameter is 1.0 mm) were evaluated with a spectrophotometer (Model Chromaview 300, Spectron Tech Co, Korea) for the shade A1, A2, A3 and A4. Distilled water (refractive index: 1.7) was used to attain optical contact between the layers. White, white gray, and white brown backgrounds were used to assess the influence of the background on the final shade. And the mean color difference value$({\Delta}E)$ was calculated. Results and conclusion: The results obtained from this study were as follows. 1. There was a significant correlation between the thickness ratio of the ceramic core/dentin porcelain system and $L^*,\;a^*\;and\;b^*$ values when the total thickness of specimen combination was smaller than 1.4 mm(P<0.05). 2. The specimen which the ceramic core thickness was more than 0.7 mm had the best masking effect against background colors. 3. The mean color difference value$({\Delta}E)$ is smaller than 2 $({\Delta}E<2)$ when the ceramic core thickness was larger than 0.7 mm and the total thickness of specimen was more than 1.4 mm.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2011년도 춘계학술대회 논문집
• /
• pp.229-230
• /
• 2011

• 한국세라믹학회지
• /
• 제34권10호
• /
• pp.1015-1020
• /
• 1997

In the Nd;YAG crystal growth by Czochralski method, the relationship between the core formation and the solid-liquid interface was observed by controlling the temperature gradient in the furnace. When the crystal was grown along<111> direction, defects and core area were reduced as the temperature gradient increased. The optimum temperature gradient was found to be higher than 4$0^{\circ}C$/cm. The Nd3+ concentration analysis by ICP-Mass showed that the segregation coefficient was about 20% higher in the core region than core-free region, where the segregation coefficients of core region and core-free region were 0.22 and 0.18, respectively.

• 치위생과학회지
• /
• 제12권2호
• /
• pp.123-129
• /
• 2012

이 연구에서는 지르코니아 코어의 두께를 달리 제작하여 동일한 색조의 상부도재를 축성함에 있어 제작방법을 다르게 하여 두 상반된 시편을 각각 분광측색장치를 이용하여 CIE $L^*,a^*,b^*$ 색체계로 산출하여 객관적으로 색차를 비교, 분석하여 다음과 같은 결론을 얻었다. 1. 지르코니아 코어의 두께가 두꺼워 지고 상부도재의 두께가 얇아지면서 $L^*$ 값의 수치는 높아지며 $a^*,b^*$ 값은 낮아지는 경향을 띠었다. 상부도재 축성방법을 다르게 제작한 시편에서도 같은 결과를 보였다. 동일한 색조 시편에서 HP군은 PST군에 비해 $L^*$ 값의 수치는 낮게 측색되어 어두운 경향을 보였으며 $a^*,b^*$ 값도 낮은 수치를 보여 황색의 경향을 띠었다. 2. HP군, PST군 모두 동일한 색조에서 지르코니아 코어 두께와 상부도재 제작방법 간에 교호작용은 없었다(P=.083). 지르코니아 코어의 두께에 따라서는 통계적으로 유의한 차이는 존재하였으며(P=.001), 두께가 0.3 mm의 시편 A1, A2 색조에서 색차 값($E^*$)은 3.7 이상으로 나타났고, 그 이외 시편에서는 3.7 이하로 분석되어 임상가능 허용치로 나타났다. 이상의 결과로 볼 때 지르코니아를 이용한 전부 도재관 제작 시 같은 색조의 재료 일지라도 제작방식과 상부도재의 재료에 따라 색차 값이 존재하므로 이를 감안하여 보철물 제작에 사용해야 할 것으로 사료되며, 특히 코어의 두께가 얇은 보철물에서는 임상 허용치 이상의 색차 값을 보이므로 코어의 두께를 좀 더 추가하여 설계한 보철물이 바람직하다고 생각된다.

• 한국재료학회지
• /
• 제11권6호
• /
• pp.465-471
• /
• 2001

수용성 매체에서 젤-케스팅 공정을 이용하여 용융실리카를 기본으로 하는 다성분계 세라믹 코어 (中子)를 제조하고, 소결조건에 따른 제반 기계적 물성과 알칼리 부식용액에 의한 용출특성을 고찰하였다. 1000cP (at $50sec^{-1}$ ) 이하의 낮은 점도를 갖는 50vol%의 고농도 다성분계 세라믹 슬림의 제조가 가능하였다. 성형체는 안정화시킨 슬림을 몰드에 부어 상온에서 겔화시킨 후 $25^{\circ}C$, 80% 상대습도 분위기 하에서 48시간동안 건조시켜 제조하였으며 건조된 성형체에는 균열이 발생하지 않았다. 세라믹 코어 성형체의 소결온도가 상승할 수록 상온강도, 겉보기 밀도, 수축률은 시편의 기공도와 역비례하여 증가하였다. 세라믹 코어 소결체의 용출속도는 동일한 온도에서 알칼리 부식용액의 농도에 의존하였으며, 소결체의 기공도가 클수록 증가하였다.

• 대한치과기공학회지
• /
• 제34권1호
• /
• pp.1-9
• /
• 2012

Purpose: The purpose of this study was to investigate the transmittance differences of pressable ceramic core due to thickness within the visible light spectrum. Methods: 36 specimens were divided into 2 groups (0.6mm, 0.8mm) which have each 3 specimens. The size of specimens was 10mm high and 10mm wide. The transmittance of specimens are measured by spectrophotometer Model Cary 500 that can measure infrared-ray, visible wave and ultraviolet-ray. Results: The results shows that there was no significant difference between specimen's thickness(0.6mm, 0.8mm) and transmittance. Conclusion: The individual's color perception is personal and there are numerous factors that influence on it. In general, human eye can perceive the color of thing only within visible light spectrum but in this experiment through spectrophotometer there was no big difference between specimen's thickness(0.6mm, 0.8mm) and transmittance. To sum up, The most important factors were a layed porcelain structure and its thickness rather than core thickness in the porcelain crown. Also, When making all ceramic core with dead pulp (nervous treatment tooth) when used as a restorative esthetic think is more efficient to improve.

• 청정기술
• /
• 제28권2호
• /
• pp.154-162
• /
• 2022

알루미늄 (Al) 금속을 전구체 및 구조체로 이용, 수열 반응을 통하여 Al@Al₂O₃와 Al@Ni-Al LDH (LDH = layered double hydroxide) 코어-쉘 복합 구조체를 합성하였다. 제조된 구조체의 형상, 조성, 결정 구조는 수용액에 존재하는 이온들에 의하여 크게 영향을 받았으며, 이를 활용하여 다양한 특성의 촉매 구조체 유도가 가능하였다. Al@Ni-Al LDH 코어-쉘 구조체의 환원을 통하여 Ni 나노 입자가 고정화된 Ni/Al@Al₂O₃ 촉매를 제조하였고, CO₂ 메탄화 반응에 적용하여 촉매의 특성을 평가하였다. Ni/Al@Al₂O₃ 촉매는 전통적 incipient wetness impregnation 방법에 의하여 제조된 Ni/Al₂O₃ 촉매에 비교하여 Ni 입자의 분산도와 균일성이 매우 높았으며 약 2 배 이상의 CO₂ 전환율로 높은 촉매적 활성과 더불어 구조의 안정성을 보여 주었다. 이러한 Ni/Al@Al₂O₃ 구조체 촉매의 우수한 특성은 Al 금속을 기반으로 한 새로운 개념의 촉매 구조체 설계와 합성 방법의 타당성을 보여준다.

• 한국세라믹학회지
• /
• 제53권2호
• /
• pp.246-252
• /
• 2016

Complex designed silica-based ceramic cores were fabricated by ceramic injection molding. Slow heating rate (0.2K/min) for debinding restrained bloating on the surface of ceramic cores. To investigate effect of sintering conditions on mechanical properties of ceramic cores, green bodies were sintered at temperatures in a range from $1150^{\circ}C$ to $1400^{\circ}C$ for various dwelling times (6 h to 48 h). Sintering above $1300^{\circ}C$ for 12 h and dwelling time over 24 h at $1200^{\circ}C$ reduce the flexural strength and increase the linear shrinkage of ceramic cores. Cristobalite, formed by high sintering temperature or long dwelling time, induces reduction of mechanical properties due to its phase transformation, which is accompanied by volume contraction and microcracking. Ceramic core sintered at $1200^{\circ}C$ for 12 h endured wax patterning and shell molding, and was manufactured successfully.

• 한국기계가공학회지
• /
• 제11권3호
• /
• pp.7-12
• /
• 2012

Ceramic core processing technology using 5-axis high-speed cutting machine is applied to make the glass molds for aspherical ophthalmic lenses. In the technology, optimum processing conditions for aspherical ceramic molds are based on minimal experimental data of surface roughness. Such surface roughness is influenced by fabricating tools, cutting speed, feed rate, and depth of cut, respectively. In this paper, we present that surface roughness and shape accuracy of aspheric ceramic mold obtained by optimum processing conditions are Pa $0.6184{\mu}m$ and Pt $5.0301{\mu}m$, respectively, and propose that these values are sufficiently possible to apply to making the glass molds for aspherical ophthalmic lenses.