• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.5
• /
• pp.451-457
• /
• 2011

The main objective of this study is to investigate the variation in the ignition characteristics of coals as a function of moisture content in a laminar flow reactor (LFR) equipped with a fuel moisture micro-supplier designed by the Pusan Clean Coal Center. The volatile ignition position and time were observed experimentally when a pulverized coal with moisture was fed into the LFR under burning conditions similar to those at the exit of the pulverizer and real boiler. The reaction-zone temperature along the centerline of the reactor was measured with a $70-{\mu}m$, R-type thermocouple. For different moisture contents, the volatile ignition position was determined based on an average of 15 to 20 images captured by a CCD camera using a proprietary image-processing technique. The reaction zone decreased proportionally as a function of the moisture content. As the moisture content increased, the volatile ignition positions were 2.92, 3.36, 3.96, and 4.65 mm corresponding to ignition times of 1.46, 1.68, 2.00, and 2.33 ms, respectively. These results indicate that the ignition position and time increased exponentially. We also calculated the ignition-delay time derived from the adiabatic thermal explosion. It showed a trend that was similar to that of the experimental data.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.3
• /
• pp.285-293
• /
• 2016

The high velocity oxygen fuel(HVOF) thermal spray is a kind of surface modification techniques to produce the sprayed coating layer. This process is to form the coating layer after spraying the powder to molten or semi-molten state by the ultra-high speed at the high-temperature heat source and conflicting with a substrate. The efficiency of thermal spraying is dropped, however, because the semi-molten powder in a spray process become a factor that degrades the mechanical property by the formed pore within the coating layer. Therefore, it is necessary to melt completely the thermal spray powder in order to produce the coating layer with an optimal adhesive force. In this study, to improve the wear resistance, corrosion resistance and heat resistance, the plungers of high-speed and ultra-high pressure reciprocating hydraulic pumps used in ironworks are manufactured with STS $420J_2$ and are coated by the powders of WC-Co-Cr and WC-Cr-Ni including the WC of high hardness using a HVOF thermal sprayer developed in this laboratory. These are called by the surface-modified plungers. The surface roughness, hardness, and surface and cross-sectional microstructure of these two surface-modified and conventional ceramic plungers are measured and compared before operation with after operation for 100 days. It is found that the values of centerline average surface roughness and maximum height for conventional ceramic plunger are 9.5 to 10.8 and 5.2 to 5.7 times higher than those of surface-modified ones coated by WC-Co-Cr and WC-Cr-Ni because the fine tops and bottoms on surface roughness curve of conventional ceramic plunger are approximately 100 times higher than those of surface-modified ones. In addition, the pores and scratches in the surface microstructure are considerably formed in the order of conventional ceramic, WC-Cr-Ni and WC-Co-Cr surface-modified plungers. The greater the WC content of high hardness powder is less the change in the plunger surface.

• Journal of Korea Water Resources Association
• /
• v.36 no.5
• /
• pp.761-776
• /
• 2003

Numerical models were employed to investigate the hydrodynamics of water flow in the lake behind a dam and the spillway where supercritical flows and negative pressures are likely to occur. In this study, 2-D model, RMA2 was employed to examine the upstream flow pattern and 3-D CFD model, FLUENT was used to evaluate the three-dimensional flow in the approaching region and flow distributions in the spillways and discharge culverts. The bathymetry and the details of structures were carefully taken into consideration in building the models. The results from applying the 2-D model for the planned Hantan River Dam show that large eddies, the velocity of which reaches up to 1 m/s are occurring in several places upstream of the dam. That means that the 2-D numerical model could be utilized to investigate the two-dimensional flow patterns after the construction of a dam. Three-dimensional numerical results show that the approach flow varies depending on stages and discharge conditions, and velocities at spillways, discharge culverts, and sediment flushing tunnels are differently distributed. The velocity distributions obtained from the numerical model and a hydraulic model at the centerline of spillways 100 m upstream of the dam show reasonably similar results. It is expected that 2-D and 3-D numerical models ate useful tools to help optimize the dam design through investigating the flow patterns in the spillway and at the upstream of the dam, which is not always feasible in hydraulic modeling.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.5
• /
• pp.1177-1189
• /
• 1994

This paper aims to develop the numerical model for prediction of the channel migration by analyzing of sediment and flow characteristics with patterns of channel in alluvial rivers. Flow in rivers constitutes to be the meandering or the braided form and rarely straight channel through morphologically stable patterns with mutual actions between the flowing water and bed materials. In order to develop the model for simulation of the channel migration, the channels are divided into two types with positive or negative sign by the direction of curvature radius of the centerline channel ($r_c$). That is, the single bend-channel consists of only one curvature of positive or negative sign and the multi-bend channel consists of two more curvatures of positive or negative sign, respectively. The model analyzes the sediment and flow characteristics under the influence of superelevation, spiral motion, irregularity in bed topography and depth-averaged velocity of channels. For reliability of this model, the single bend-channel and the multi bend channel are compared with experiment data in other models and the measured field data in the Keum-River, respectively. As a result, the both com parisians turn out to be excellent.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.5
• /
• pp.509-515
• /
• 2012

In this study, ${\gamma}-Al_2O_3$ nanoparticles were synthesized by using coflow hydrogen diffusion flames. The synthesis conditions were varied with using several oxygen concentrations in the oxidizing air. The particle characteristics of the flame-synthesized $Al_2O_3$ nanoparticles were determined by examining the crystalline structure, shape, and specific surface area of the nanoparticles. The measured maximum centerline temperature of the flames ranged from 1507.8 K to 1998.7 K. The morphology and crystal structure of the $Al_2O_3$ nanoparticles were determined from SEM images and XRD analyses, respectively. The particle sizes were calculated from measured BET specific surface areas and ranged from 25 nm to 52 nm. From XRD analyses, it was inferred that a large number of the synthesized nanoparticles were ${\gamma}-Al_2O_3$ nanoparticles including ${\theta}-Al_2O_3$ nanoparticles.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.2
• /
• pp.197-204
• /
• 2013

A method was developed for analyzing the radiation heat transfer from the duct burner flame to the heat exchanger in a heat recovery steam generator (HRSG) in order to supplement the existing thermal design process. The burner flame and the heat exchanger were considered to be imaginary planes, and the flame temperature, surface, and emissivity were simplified using an engineering approach. Three analysis cases in which the duct burner position and fuel were changed were considered. The calculated flame radiative heat transfer and local flux on the heating surface were compared with those of 3-atomic gas radiation and convection. In all analysis cases, heat transfer by 3-atomic gas radiation was very small. The ratio of the flame radiative heat transfer to the convection heat transfer on the heating surface was estimated to be as high as 8-41%. Moreover, the local heat flux on the heating surface centerline was dominated by flame radiative heat flux.

• Journal of The Korean Astronomical Society
• /
• v.37 no.1
• /
• pp.41-53
• /
• 2004

It has been a big mystery what drives filament eruptions and flares. We have studied in detail an X1.8 flare and its associated filament eruption that occurred in NOAA Active Region 9236 on November 24,2000. For this work we have analyzed high temporal (about 1 minute) and spatial (about 1 arcsec) resolution images taken by Michelson Doppler Imager (MDI) onboard the Solar and Heliospheric Observatory, Hoc centerline and blue wing ($-0.6{\AA}$) images from Big Bear Solar Observatory, and 1600 ${\AA}$ UV images by the Transition Region and Corona Explorer (TRACE). We have found that there were several transient brightenings seen in H$\alpha$ and, more noticeably in TRACE 1600 ${\AA}$ images around the preflare phase. A closer look at the UV brightenings in 1600 ${\AA}$ images reveals that they took place near one end of the erupting filament, and are a kind of jets supplying mass into the transient loops seen in 1600 ${\AA}$. These brightenings were also associated with canceling magnetic features (CMFs) as seen in the MDI magnetograms. The flux variations of these CMFs suggest that the flux cancellation may have been driven by the emergence of the new flux. For this event, we have estimated the ejection speeds of the filament ranging from 10 to 160 km $s^{-1}$ for the first twenty minutes. It is noted that the initiation of the filament eruption (as defined by the rise speed less than 20 km $s^{-1}$) coincided with the preflare activity characterized by UV brightenings and CMFs. The speed of the associated LASCO CME can be well extrapolated from the observed filament speed and its direction is consistent with those of the disturbed UV loops associated with the preflare activity. Supposing the H$\alpha$/UV transient brightenings and the canceling magnetic features are due to magnetic reconnect ion in the low atmosphere, our results may be strong observational evidence supporting that the initiation of the filament eruption and the preflare phase of the associated flare may be physically related to low-atmosphere magnetic reconnection.

• Journal of Navigation and Port Research
• /
• v.29 no.1 s.97
• /
• pp.9-15
• /
• 2005

To design ship channel is one of important factors for planning and developing a port. In most case, the core factors for designing ship channel are the layout and width of channel provided the net underkeel clearance is secured to be safe enough to pass. In this study, Variable Bumper Area(VBA) model is applied to design and assess ship channel. This model reflects ship's particular, ship domain theory, ship speed and mariner's ship handling skill and experience, especially external forces which cause leeway, set and drift and the change of ship maneuvering characteristics. A real time, full mission shiphandling simulator is used to analyze ship dynamic data according to mariner's ship control, external forces, ete. This model defines Domain degree and Domain-index for assessing the efficiency and safety of the channel. The proposed model is applied to Ulsan new port plan which has a channel width of 1.5 times the length of the largest vessel, a radius of 5 times the length of the largest vessel in a curve of 57 degree centerline angle and SBM facility adjacent to the lateral edge of channel. The result of this study shows that the width of the channel and radius of channel curve are suitable for the target ship but the difficulty of ship handling is caused by the large course change and SBM located in the vicinity of channel.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.2D
• /
• pp.111-119
• /
• 2012

In this study, the effect of safety improvement project was analyzed, and a decision making model for traffic accident reduction measures was suggested. The results of this study are as follow; First the overall number of traffic accidents and casualties were reduced, especially reduced the number of unauthorized crossing and centerline encroachments was remarkable. Second, the priorities of traffic accident reduction measures. through hazards roadway section improvement projects were determined. As, higher level evaluation items of AHP hierachy structure include civil facilities and transportation facilities. The civil facilities has 6 lower level evaluation items and transportation facilities has 4 items. The results of this study, It was revealed that traffic experts prefer civil facilities more than transportation facilities and the top 2 items of the each data (or index) took over 50%. In addition, one of the last evaluation contents through the verification, the top 3 items of civil facilities took 55.38%. The project according to the improvement projects for hazards roadway reduced traffic accidents and casualties as well as saving the cost. So these results should be available for basic information for the countermeasure about reducing the traffic accidents by local governments.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.24 no.2
• /
• pp.77-83
• /
• 2012

Numerical analyses through Computational Fluid Dynamics have been performed to investigate the seawater flow field characteristics for various shrouds used in horizontal axis tidal current turbine systems. Seawater flow characteristics are largely influenced under constant tidal current velocity by the shroud geometry and there is considerable difference in fluid velocity distributions around the shrouds. Especially the location and magnitude of maximum seawater flow velocity directly affect turbine performance for power generation. For the cylinder-diffuser type shroud system whose cylinder and diffuser parts have the same length accelerated flow region is formed in the overall cylinder part while maximum velocity in the nozzle-diffuser type whose nozzle and diffuser parts have the same length with symmetry, locally appears near the minimum sectional area. In case of cylinder-diffuser type shroud fluid velocity increases rather high compared with current velocity. And fluid velocity at the centerline gradually increases from the entrance, and then decreases rapidly after reaching a peak close to the middle of the cylinder part unlike the nozzle-diffuser while there is not much variation near the rear of the shroud. These results of the seawater flow characteristics with various shroud geometries can be applied to optimal design for the development of efficient tidal current power generation systems.