• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.900-904
• /
• 1997

A problem in the grinding process using the machining center(MC) with a small diametric wheel is the machining error due to due to decrease of quill diameter. In this paper, a side-cut grinding is performed with a vitrified bonded CBN wheel by the MC, and the relation between grinding force and machining error for grinding conditions is investigated experimentally. It is show that the normal force has a significant effect on the machining error.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.1522-1529
• /
• 2009

When a shaft is excavated in Korea, the mechanized method such as RBM(Raise Boring Machine) or RC(Raise Climber) is used independently of depth. But usually, the mechanized method is useful for the deep depth. On the contrary, when the depth of shaft is short, the cost of excavation increase. So in the case of shaft constructon less than 100m, we need to consider more suitable method of shaft construction such as Stage-cut which is one of blasting methods. Stage-Cut is widely used in the field of shaft construction in Japan as a tool of rock excavation. The main purpose of this study is to provide technical guidance for design and construction of shafts in rock, using Stage-cut method which is suitable for 20m~80m depth shaft. In this study, Blasting tests was performed in field, according to rock classification. Finally, the stage-cut method which is suitable for the geology of Korea was developed.

• Journal of Korea Foundry Society
• /
• v.29 no.1
• /
• pp.33-37
• /
• 2009

Cartesian grid system has mainly been used in the casting simulation even though it does not nicely represent sloped and curved surfaces. These distorted boundaries cause several problems. A special treatment is necessary to clear these problems. In this paper, we propose a new method that can consider the cutting cells which are cut by casting and mold based on the partial cell treatment (PCT). This method provides a better representation of geometry surface and will be used in the computation of velocities that are defined on the cell boundaries in the Cartesian grid system. Various test examples for several casting process were computed and validated. The analysis results of more accurate fluid flow pattern and less momentum loss owing to the stepped boundaries in the Cartesian grid system were confirmed. By using the cut cell method, performance of computation gets better because of reducing the whole number of meshes.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.3
• /
• pp.68-72
• /
• 2012

Al2017 is typical Duralumin of self-hardening aluminum alloy. It is lightweight, formability and machinability so throughout the industries have widely used automobile, electronics, semiconductor and aircraft as material. A variety of CNC machine tool processing technology, scientific principles and experience have been studied in order to increase accuracy and productivity. Using a machining center is to constant amount of side step and cutting characteristics studied changing depth of cut, revolution per minute and feed rate.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.14 no.1
• /
• pp.18-23
• /
• 2010

Purpose: PET/CT combines functional and morphologic data and increases diagnostic accuracy in a variety of malignancies. Especially reconstructed Fusion PET/CT images or MIP (Maximum Intensity Projection) images from a 2-dimensional image to a 3-dimensional one are useful in visualization of the lesion. But in Fusion & MIP 3D reconstruction image, due to hot uptake by urine or urostomy bag, lesion is overlapped so it is difficult that we can distinguish the lesion with the naked eye. This research tries to improve a distinction by removing parts of hot uptake. Materials and Methods: This research has been conducted the object of patients who have went to our hospital from September 2008 to March 2009 and have a lot of urine of remaining volume as disease of uterus, bladder, rectum in the result of PET/CT examination. We used GE Company's Advantage Workstation AW4.3 05 Version Volume Viewer program. As an analysis method, set up ROI in region of removal in axial volume image, select Cut Outside and apply same method in coronal volume image. Next, adjust minimum value in Threshold of 3D Tools, select subtraction in Advanced Processing. It makes Fusion & MIP images and compares them with the image no using Region Cut Definition. Results: In Fusion & MIP 3D reconstruction image, it makes Fusion & MIP images and compares them by using Advantage Workstation AW4.3 05's Region Cut Subtraction, parts of hot uptake according to patient's urine can be removed. Distinction of lesion was clearly reconstructed in image using Region Cut Definition. Conclusion: After examining the patients showing hot uptake on account of volume of urine intake in bladder, in process of reconstruction image, if parts of hot uptake would be removed, it could contribute to offering much better diagnostic information than image subtraction of conventional method. Especially in case of disease of uterus, bladder and rectum, it will be helpful for qualitative improvement of image.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.731-734
• /
• 2005

Cut slopes are collapsed in Korea every year. Cut slope collapses cause a loss of lives and assets. Many researchers make clear collapse factor of cut lope. Fresh rock weathered through reaction undergroundwater and groundwater. During weathering process, weathered minerals are created. Weathered minerals are analysed by X-ray diffraction meter. X-ray diffraction meter make possible quantity assessment of degree of weathering and indicator of potential collapse possibilities. This paper discuss possibilities of cut slope dangerous with analysis of weathered minerals of cut slope.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.5
• /
• pp.423-430
• /
• 2012

In this paper, the effect of wrinkling on the cut propagation direction of thin membrane was studied using geometrically nonlinear shell element post-buckling analysis. In the analysis, rectangular tensile membrane configuration with a slanted center cut was considered. The cut propagation direction was predicted by maximum energy release rate method, $K_{II}$-zero method, and maximum tangential stress method. The cut propagation angle and the $J$-integral values were calculated for the wrinkled and unwrinkled cases and the results were compared. Various initial cut orientation angles were considered and the effect on the propagation direction was studied. The cut propagation paths were also predicted by virtual cut extension approach.

• Journal of the Korean Arthroscopy Society
• /
• v.7 no.2
• /
• pp.215-219
• /
• 2003

Purpose : To report the 'condylar cut-off sign', a new radiographic sign in knees with discoid lateral meniscus and to report the sensitivity, specificity, positive predictive value and negative predictive value of the sign to elucidate the diagnostic significance of the sign for discoid meniscus. Materials and Methods : Fifty knees with complete discoid lateral meniscus and fifty normal knees formed the basis of this study. All of them were arthroscopically confirmed fer the discoid or normal lateral meniscus. The authors developed a method to measure the length of the medial and lateral condylar were compare and analyzed. Results : Tile average ratio was 0.716 in the discoid meniscus group, and 0.902 in the normal group. The stastistical analysis by the T-test revealed the t-value -11.13(p<0.0001). Stastistical analysis by chi-square test using cut point 0.8, also showed significant difference between the two groups, with $76\%$ sensitivity, $100\%$ specificity, $100\%$ positive predictive predictive value and $81\%$ negative predictive value. The 'condylar cut-off sign' was readily detectable in all cases of discoid lateral meniscus, suggesting that the cut off sign could serve as a simple and reliable radiographic sign fur the diagnosis of discoid meniscus. Conclusion : The condylar cut-off sign on the Tunnel view of simple radiography of the knee can serve as a good sign for the diagnosis of discoid lateral meniscus, with $100\%$ positive predictive value.

• Proceedings of the KSRS Conference
• /
• 2002.10a
• /
• pp.524-529
• /
• 2002

In this paper, we report the development of two DEM (digital elevation model) generation algorithms over urban areas from an IKONOS stereo pair. One ("EpiMatch") is originally developed for SPOT images and modified for IKONOS images. It uses epipolar geometry for accurate DEM generation. The other is based on graph-cut algorithm in 3D voxel space. This algorithm is believed to work better on height discontinuities than EpiMatch. An IKONOS image pair over Taejon city area was used for tests. Using ground control points obtained from differential GPS, camera model was set up and stereo matching applied. As a result, two DEMs over urban areas were produced. Within a DEM from EpiMatch small houses appear as small "cloudy" patches and large apartment and industrial buildings are visually identifiable. Within the DEM from graph-cut we could achieve better height information on building boundaries. The results show that both algorithms can generate DEMs from IKONOS images although more research is required on handling height discontinuities (for "EpiMatch") and on faster computation (for "Graph-cut").

• International Journal of High-Rise Buildings
• /
• v.8 no.4
• /
• pp.303-311
• /
• 2019

The effectiveness of aerodynamic modification to reduce wind loadings has been widely reported. However, most of previous studies have been investigated dynamic forces and pressure distributions on tall buildings with various unconventional configurations. This study was investigated dynamic characteristics and aerodynamic instability of super-tall buildings with unconventional configurations through extensive aeroelastic model experiments. Seventeen types of supertall building models were considered such as basic and corner modification with corner cut, chamfered, oblique opening, tapered, inversely tapered, bulged, helical with twist angles of $90^{\circ}$, $180^{\circ}$, $270^{\circ}$, $360^{\circ}$ and composite with $360^{\circ}$ helical & corner cut, 4-tapered & $360^{\circ}$ helical & corner cut, setback & corner cut, setback & $45^{\circ}$ rotate. As a result, aerodynamic characteristics of helical models with single modification are superior to those of other models with single modification. However, effect of twist angle for helical model is negligible. Further, the 4-tapered & $360^{\circ}$helical & corner cut model is most effective in reducing the along- and across-wind fluctuating displacement responses in all of experimental models.