• Journal of the Korea Concrete Institute
• /
• v.16 no.3 s.81
• /
• pp.433-440
• /
• 2004

In order to improve the performance of concrete, generally, modern cements often incorporate several mineral admixtures. In this study, the experimental included the flow value, air content of mortar containing limestone powder and length change and compressive strength of mortar specimen immersed in sulfate solutions. From the experimental results, the limestone powder cement matrices improved the physical properties and sulfate resistance of cement matrices at $10\%$ replacement ratio of limestone powder. The $30\%$ replacement ratio of limestone powder was significantly deteriorated in sodium sulfate solution. Irrespective of fineness levels of limestone powder, length change and SDF of mortar specimens with only $10\%$ replacement was much superior to the other replacements.

• Journal of the Korea Concrete Institute
• /
• v.13 no.6
• /
• pp.561-567
• /
• 2001

It is reported that a lot of sludge powder is produced during the process of manufacturing crushed fine aggregate in mines. However, there is a limitation on the its use that most of them are disposed and wasted, which cause environmental pollution. Therefore, in this paper, tests are carried out in order to recycle sludge powder as filler for cement mortar products. Kinds of aggregates and mix proportion of mortar are varied under various contents of sludge powder. According to test results, it is found that cement mortar products using sludge powder as substitution of fine aggregate about 10% have better qualities than those without sludge powder.

• Korean Journal of Materials Research
• /
• v.20 no.1
• /
• pp.1-6
• /
• 2010

Geopolymer materials are attractive as inorganic binders due to their superior mechanical and eco-friendly properties. In the current study, geopolymer-based cement was prepared using aluminosilicate minerals from fly-ash with KOH as an alkaline-activator and $Na_2SiO_3$ as liquid glass. Then, calcium carbonate powder from a clam shell was mixed with the geopolymer and the mixture was coated on a concrete surface to provide points of attachment for environmental organisms to grow on the geopolymers. We investigated the effect of the shell powder grain size on the microstructure and bonding property of the geopolymers. A homogeneous geopolymer layer coated well on the concrete surface via aluminosilicate bonding, but the adhesiveness of the shell powder on the geopolymer cement was dependent on the grain size of the shell powder. Superior adhesive characteristics were shown in the shell powder of large grain size due to the deep penetration into the geopolymer by their large weight. This kind of coating can be applied to the adhesiveness of eco-materials on the surface of seaside or riverside blocks.

• Advances in concrete construction
• /
• v.5 no.1
• /
• pp.65-74
• /
• 2017

This study was focused on the use of partial replacement of cement with glass powder in high strength concrete and also copper slag as a partial replacement of coarse sand in concrete. The high strength concrete was prepared with different mineral admixtures like silica fume, fly ash and rice ash husk in different proportions. An experimental investigation has been carried to study about the effect of glass powder on high strength copper slag concrete. The range of glass powder was 10%, 15% and 20% as a replacement of cement. The range of copper slag was 0%, 20%, 40% and 60% as a replacement of natural sand. In addition to the different percentage of fly ash, silica fume, and rice husk ash 5% and 10% was also studied in copper slag concrete. Thus, a total of 51 cubes were casted and compressive strength test was performed on them. The result of the study shows that the value of average compressive strength of concrete after addition of 10%, 15% and 20% of glass powder are 70.47, 72.01 and 73.31 respectively. The value of average compressive strength after addition of 20%, 40% and 60% copper slag as a replacement of sand are 72.18, 74.38 and 73.08 respectively. The value of average compressive strength after addition of 5% and 10% fly ash as a replacement of cement are 71.56 and 73.22. The value of average compressive strength after addition of 5% and 10% silica fume as a replacement of cement are 72.33 and 73.53. The value of average compressive strength after addition of 5% and 10% rice husk ash as a replacement of cement are 72.86 and 69.49. At the level of 20% replacement of cement by glass powder meets maximum strength as compared to that of controlled concrete and copper slag high strength concrete.

• Journal of the Korea Institute of Building Construction
• /
• v.2 no.2
• /
• pp.145-150
• /
• 2002

The hydration of cement paste occurs when the cement is miked with water. During the hydration, hydration heat causes the thermal stress depending on the site of concrete and the cement content. Especially in the high-strength concrete, we must give care to the concrete due to its large cement content. In this study conduction calorimeter and concrete insulation hydration heat meter were used to investigation the hydration heat characteristics of cement and concrete. To reduce hydration heat of high-strength concrete, several types of replacement of fly-ash and blast-furnace slag powder were used in this experiment. As a result of this study, it was found that hydration heat of high-strength concrete was reduced by replacement of fly-ash and blast-furnace slag powder. In case of high-strength concrete using blast-furnace slag powder, the max-heat arrival time was delayed but an effect of heat reduction was lower than a case of high-strength concrete using fly-ash, because it was considered that the heat-dependence property of blast-furnace slag powder was higher than that of fly-ash.

• Computers and Concrete
• /
• v.11 no.1
• /
• pp.63-73
• /
• 2013

In this study, the effect of reducing cement by proportional addition of waste powder rubber on the performance of concrete under impact three-point bending loading were investigated experimentally and numerically. Concrete specimens were prepared by adding 5%, 10% and 20 % of rubber powder as filler to the mix and decreasing the same percentage of cement. For each case, three beams of $50mm{\times}100mm{\times}500mm$ were loaded to failure in a drop-weight impact machine by subjecting them to 20 N weight from 300mm height, while another three similar beams were tested under static load. The bending load-displacement behavior was analyzed for the plain and rubberized specimens, under static and impact loads. A three dimensional finite-element method simulation was also performed by using LUSAS V.14 in order to study the impact load-displacement behavior, and the predictions were validated with the experimental results. It was observed that, despite decreasing the cement content, the proportional addition of powder rubber until 10% could yield enhancements in impact tup, inertial load and bending load.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.05a
• /
• pp.212-213
• /
• 2017

The study investigated the fluidity and compressive strength of non-cement porous block using blast furnace slag powder to reduce CO₂ in the construction industry.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.05a
• /
• pp.283-286
• /
• 2012

According to increase of the waste concrete occurrence, recycling has being important more and more. This study is to recycle the waste concrete powder, which is occurred in dry-process during recycling of construction waste. We have tried the waste concrete powder to apply as the replacement of the silica powder in cement extruding product. As a result, it is satisfied that the autoclave cured pannel of 50% replacement ratio of waste concrete powder staisty the level of the flexural strength of 14MPa stipulated by "KS F 4735 Extruding concrete panel" was the same thermal properties as base specimen.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.42 no.5
• /
• pp.125-132
• /
• 2000

This study was performed to evaluate the physical properties of reinforced soil mixture powder. Soil sample was prepared by passing into the standard sieve of No. 200 and reinforcement materials were calcium carbonate, quicklime and portland cement. Fineness, setting time, and compressive strength test for reinforced soil mixture powder were performed and analyzed to investigate their physical properties. The main results were summarized as follow. The compressive strength of soil mixture powder itself and most reinforced was reinforced according to increasing in the mixture rate of reinforcement and the rate of increase was remarkably higher in the cement reinforced soil moisture powder. It was appeared that the early compressive strength is considering higher in the cement reinforced soil moisture powder with 2% of moisture rate of accelerator.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2005.10a
• /
• pp.108-112
• /
• 2005

In this research, the physical properties of fresh concrete using lime stone powder as a part of cement were investigated. Fresh concrete using lime stone powder was prepared with various lime stone powder replacement($5{\sim}12$ volume %) for cement and the quantities of sand aggregate ratio in concrete were 47.3%, 48.5% and 49.4% of ratio of sand aggregate. The workability, flowing characteristics, air content and bleeding of concrete using lime stone powder were tested and the results were compared with those of ordinary portland cement concrete. In the experiment, we acquired satisfactory results at the point of fresh concrete characteristics using lime stone powder within the replacement ratio of $8{\sim}12%$ and the optimum quantity of sand aggregate ratio in concrete was found to be $48.5%{\sim}50%$ of ratio of sand aggregate.