• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2005년도 추계 학술논문 발표대회
• /
• pp.75-78
• /
• 2005

This raper investigates the effect of curing temperature on strength development of concrete incorporating cement kiln dust(CKD) and blast furnace slag (BS) quantitatively. Estimation of compressive strength of concrete was conducted using equivalent age equation and rate constant model. An increasing curing temperature results in an increase in strength at early age, but with the elapse of age, strength development at high curing temperature decreases compared with that at low curing temperature. Especially, the use of 35 has a remarkable strength development at early age and even at later age, high strength is maintained due to accelerated pozzolanic activity resulting from high temperature. Whereas, at low curing temperature, the use of BS leads to a decrease in compressive strength. Accordingly, much attention should be paid to prevent strength loss at low temperature. Based on the strength development estimation using equivalent age equation, good agreements between measured strength and calculated strength are obtained.

• Advances in nano research
• /
• 제4권3호
• /
• pp.181-195
• /
• 2016

Addition of nano-$SiO_2$ (NS) to geopolymer composites has been studied through measurement of compressive strengths, FTIR and XRD analysis. Alumino-silicate materials are coarse aggregate included waste concrete and demolished walls with its cementing binder, cement kiln dust (CKD) used and can possess a pronouncing activation for the geopolymer reaction resulting from the high alkali contents within. Materials prepared at water/binder ratios in a range of 0.30: 0.40 under curing of $40^{\circ}C$ and 100% Relative Humidity (R.H.), while the used activator is sodium hydroxide in the ratio of 2 wt. %. First, CKD is added in the ratio from 10 up to 50 wt., %, and the demolished walls was varied depending on the used CKD content, while using constant ratio of waste concrete (40 wt., %). Second step, depending on the optimum CKD ratio resulted from the first one (40 wt. %), so the control geopolymer mix composed of cement kiln dust, demolished walls and waste concrete in the ratio (40:20:40, wt %). Nano-silica partially replaced waste concrete by 1 up to 8%. Results indicated that, compressive strengths of geopolymer mixes incorporating nano-silica were obviously higher than those control one, especially at early ages and specially with 3%NS.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 춘계학술대회 논문집
• /
• pp.1757-1763
• /
• 2011

In recent years, accordance to industrial development project on railway investment, adverse environmental issues of the investment, such as disputed cases about recycling and usage of Ballast Cleaner excavated soil, have been continuously increasing. It will not only enhance the regulation of soil contamination but take considerable time and cost in future. In this study, we investigated soil contamination and burnability with soil of Chungang Line, Taebaek Line, Chungbuk Line, in order to seize a possibility of recycling Ballast Cleaner excavated soil for the natural materials and substantial heat sources, which are necessary resources for cement manufacturing process. As a result of this study, It is found that Ballast Cleaner excavated soil is satisfied with a standard. The excavated soil contains a lot of cement ingredients and fossil fuel dust incurred from freight transportation, so it is expected to use for ingredients of cement and replacement of heat sources.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.743-747
• /
• 2005

In South Korea, about 900 metal mines have been abandoned, and about 88 million-t metal mine wastes have been discarded in recent years. The treatment of the tailings which are the main wastes in the abandoned metal mines becomes a social problem because they cause environmental pollution such as acidic waste water generation, groundwater contamination, and dust generation. Since almost whole quantities of the tailings have disposed by landfill now, the development of effective recycling methods for the tailings are strongly requested. It is expected that the fine tailings obtained by centrifugal separation process among the tailings can be utilized as admixture for cement. The purpose of this study is to evaluate the micro-structure of cement mortar admixed with fine tailing. Various admixtures were made of Fine tailings and 2 Types of OPC, fly-ash and blast furnace slag. The hydration reactivity of cement mortar with FT was examined by Porosity, XRD and SEM morphology analysis. The anolytical result about hardened hydrates shows that waste fine tailing help hydrates none densified due to it,s filling-space, These densified effect is concluded with improving the resistance to attack of cement mortar including waste fine tailing.

• 에너지공학
• /
• 제7권1호
• /
• pp.103-112
• /
• 1998

산업용 직물여과포의 운전에서 발견되는 다양한 문제점들을 해결하기 위한 일환으로 내열성여과포를 개발하여 성능을 규명하였다. 국내 산업체에서 배출되는 대표적인 네 종류의 먼지들, 즉 제철공정의 코크먼지, 시멘트 제조업체의 시멘트 먼지, 유동층 연소로의 비산회재, 그리고 폐플라스틱 소각로의 연소재에 대하여 여과포의 성능을 시험하였다. 내열성여과포의 물리화학적 특성은 평균 세공흐름압력 및 기포점 세공지름, 평균흐름 세공지름, 세공크기분포, SO2 및 NO2 분위기에서의 물성변화의 항목으로 평가 되었다. 또한, 벤치규모의 필터시험장치에서 직물여과포에 대한 압력손실, 먼지 통과율, 여과포 성능 평가지수를 조사하였다. 본 연구에서 개발된 직물여과포는 양호한 물리화학적 필터 특성을 지니고 있으며 전형적인 산업체 먼지를 처리하는데 적합하였다.

• 대한환경공학회지
• /
• 제39권8호
• /
• pp.449-455
• /
• 2017

기준공정과 개선대상공정 간의 투입물(Input, Material and energy), 배출물(Output, Product, Co-product), 환경오염물(Environmental emission) 데이터를 수집하고 공정 성과를 분석하였다. 이를 통해 환경적으로 주요한 투입물과 환경오염물을 파악하였다. 제조공정의 투입물과 환경오염물 간의 상관관계 분석을 통해 각 환경오염물에 대한 기여도가 큰 투입물을 파악하였다. 주요 환경오염물 처리 시, 경제적 최적화를 통한 종말처리공정 조합을 선형 프로그래밍 기법을 사용하여 규명하였다. 사례 연구로는 동일한 형태의 시멘트를 생산하는 EU와 국내 시멘트 제조공정을 선정하였다. 국내 시멘트 제조공정에서는 석탄이 주요 투입물로, 먼지, $SO_x$가 주요 환경오염물로 파악되었다. 제조공정의 투입물과 환경오염물 간의 다중회귀분석결과 석탄>원자재>석고 순으로 $CO_2$발생량에 기여도가 큰 것으로 나타났다. $SO_x$발생량의 경우 석탄의 기여도가 가장 컸으며, Dust 발생량의 경우 석고>원자재 순으로 기여도가 큰 것으로 나타났다. Dust 종말처리공정 최적화에서 전기집진기술 100%, 섬유필터기술 2.4% 조합이 최적이었다. $SO_x$종말처리공정 최적화에서는 건식첨가공정기술 100% 습식세정기술 25.88% 조합이 최적이었다. 이 연구의 특징은 제조공정에서 문제가 되는 주요 투입물과 환경오염물을 파악하는 방법을 제시하였다는 점이다. 또한, 기술적 경제적으로 최적의 조합인 종말처리공정 선정 방법을 제시하였다는 점이다.

• 자원리싸이클링
• /
• 제18권6호
• /
• pp.46-53
• /
• 2009

석재 가공 시 발생되는 석분은 산업폐기물로 되어있다. 현재 이 석분은 지하에 매립하거나 지상에 야적되어 방치되고 있어 폐기물로 처리하는 데 많은 비용이 요구되고 있고, 토질과 지하수 등의 환경오염의 원인이 되고 있다. 또한 콘크리트의 주재료인 골재의 공급이 부족한 현실을 고려하여 본 연구에서는 폐석분을 콘크리트 혼화재료로 재활용할 수 있는 가능성을 연구하고자 한다. 석분함유량에 대한 시멘트비를 조정한 결과, $20{\sim}30\;N/mm^2$의 콘크리트의 압축강도가 나타났고 이는 석분의 함유에 따라 압축강도가 감소되지 않음을 알 수 있었다. 석재 가공 시 발생되는 석분을 콘크리트 혼화재료로 재순환하여 사용하여도 콘크리트의 압축강도에는 전혀 문제가 없음을 알 수 있었다.

• 열처리공학회지
• /
• 제36권1호
• /
• pp.22-32
• /
• 2023

In general, when scrap is dissolved in an electric arc furnace, the amount of electric furnace steel dust (EAFD) generated is about 1.5% of the scrap charge amount, and the electric furnace steel dust collected by the bag filter is charged into the Rotary Kiln or Rotary Hearth Furnace (RHF), and the zinc component is recovered as crude zinc oxide, at which time a clinker of Fe-Base is generated. In this research, first, for the efficient resource conversion of electric furnace steel dust, a reduction and roasting experiment was conducted and the reaction kinetics was examined. As a result of the experiment, it was observed that the reduction and roasting reaction was actively conducted in the range of 1100~1150℃, and melting occurred in the range of 1250℃. In the past, this clinker was widely used as a roadbed material for road construction and an Fe-Source for cement production, but in recent years, it has been mainly reclaimed due to strengthening environmental standards. However, landfill treatment is by no means a desirable treatment method due to environmental pollution caused by leachate, expensive landfill costs, and waste of Fe resources. Therefore, in order to more actively recycle the Fe component in the clinker, first of all the clinker was pulverized into an optimal particle size, and anthracite and binder (starch) were added to the magnetic material obtained by specific gravity and magnetic separation for briquet. As a experimental results, it was possible to efficiently separate clinker as Fe component and other slag component by specific gravity and magnetic force. As a results of loading and dissolving the manufactured briquet clinker in an electric arc furnace, it was observed that the unit of power and production yield were clearly improved and the carbon addition effect in molten metal was also somewhat.

• 한국세라믹학회지
• /
• 제53권1호
• /
• pp.13-17
• /
• 2016

It is highlighted that increasing the adsorbent surface area on volumetric basis is very important in providing an easy access for gas molecules. Fine particles around $3{\mu}m$ of soft-burned dolomite kiln dust (SB-DKD) were hydrated to wet slurry samples by ball mill process and then placed in a chamber to use spray dryer method. Spherical granules with particle size distribution of $50{\sim}60{\mu}m$ were prepared under the experimental condition with or without addition of a pore-forming agent. The relationship between bead size of the pore-forming agent and size of SB-DKD particles is the most significant factor in preparation of spherical granules with a high porosity. Whereas addition of smaller beads than SB-DKD resulted in almost no change in the surface porosity of spherical granules, addition of larger beads than SB-DKD contributed to obtaining of the particles with both 15 times larger average pore volume and 1 order of magnitude larger porosity. It is considered that spherical granules with improved $N_2$ gas adsorption ability may also be utilized for other atmospheric gas adsorption.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2020년도 봄 학술논문 발표대회
• /
• pp.138-139
• /
• 2020

With the rapid progress of industrialization, indoor air quality is a very important factor for modern people who spend most of their day indoors. The recent issue of fine dust and radon on the portal site's popularity search shows that interest in indoor air quality has increased. Fine dust causes respiratory diseases, and radon causes severe lung cancer. The new material was tested using plant activated carbon, palm activated carbon and bamboo activated carbon. Both palm activated carbon and bamboo activated carbon are porous materials and generate smooth physical adsorption. As a result of the experiment, both the activated carbon tends to gradually decrease in strength and fluidity as the replacement ratio increases. The reason for this is that both activated carbons have the property of absorbing moisture, so it is judged that the strength is lowered by absorbing moisture necessary for curing. In the case of fluidity, it is judged that the fluidity is reduced by absorbing the moisture required for the flow. In the future, if the problem of the color of the finished cured body is compensated, it will be possible to manufacture a functional finishing board to replace the existing interior finishing material.