• 한국구조물진단유지관리공학회 논문집
• /
• 제11권4호
• /
• pp.121-128
• /
• 2007

본 연구는 실리카 퓸을 사용한 시멘트 경화체의 황산염침식 저항성을 평가하기 위하여 수행되었다. 실리카 퓸을 시멘트 중량에 대하여 0, 5, 10 및 15%의 4단계로 대체한 모르타르 및 0 및 10%의 2단계로 대체한 페이스트를 제조하여 침지실험을 실시하였다. 황산나트륨용액에 510일 동안 모르타르 및 페이스트를 침지한 후 재령별 외관조사, 팽창, 압축강도 감소율 및 공극특성을 조사한 결과, 실리카 퓸 대체율에 관계없이 실리카 퓸을 대체한 시멘트 경화체는 황산염침식에 대하여 저항성이 매우 우수하였으나, 보통포틀랜드시멘트 모르타르 및 페이스트는 황산염침식에 의한 극심한 성능저하 현상이 관찰되었다.

• Advances in concrete construction
• /
• 제10권6호
• /
• pp.515-526
• /
• 2020

Cold-mixed asphalt mixture is a widely recommended asphalt pavement materials with potentially economic and environmental benefits. Due to the reduction of natural non-renewable mineral resources, powder minerals with similar properties are considered as new mineral fillers in asphalt mixtures. This study explored the feasibility of using cement to replace natural limestone powder (LP) in emulsified asphalt concrete modified by styrene-butadiene styrene copolymer. The experimental tests, including compressive strength, Marshall stability as well as moisture susceptibility test, were used to investigate the mechanical properties, the Marshall stability, flow value, as well as the moisture damage. In addition, the influence of material composition on the performance of asphalt concrete is explained by the microstructure evolution of the pore structure, the interface transition zone (ITZ), and the micromorphology. Due to mineralogical reactivity of cement, its replacement part of LP improved the mechanical properties, Marshall stability, but it will reduce the moisture susceptibility and flow value. This is because with the increase of the cement substitution rate, the pore structure of the asphalt concrete is refined, the width of ITZ becomes smaller, and the microstructure is more compact. In addition, asphalt concrete with a larger nominal particle size (AC-16) has relatively better performance.

• 콘크리트학회논문집
• /
• 제16권4호
• /
• pp.549-555
• /
• 2004

Cement of three alkalinities (equivalent alkalinities of 0.36,0.52 and 0.97) was employed in fabricating a set of classical G109 type specimens. To-date, these have been subjected to a one week wet-one week dry cyclic pending using 15 w/o NaCl solution. At the end of the dry period, potential and macro-cell current were measured to indicate whether the top reinforcing steel was in the passive or active state. Once this bar became active, the specimen was autopsied and the extent of corrosion was documented. Subsequent to visual inspection, concrete powder samples were collected from the upper region of the top rebar trace; and at a certain times concrete cores were taken from non-reinforced specimens. Using these, determinations were made of (1) critical chloride concentration for corrosion initiation ($Cl_{th}^-$), (2) effective chloride diffusion coefficient ($D_e$), and (3) pore water alkalinity ($[OH^-]$). The pore water alkalinity was strongly related to the alkali content of cement that was used in the mix. The chloride concentration, ($Cl^-$), was greater at active than at passive sites, presumably as a consequence of electro migration and accumulation of these species at active site subsequent to corrosion initiation. Accordingly, ($Cl^-$) at passive sites was considered indicative of the threshold concentration fur corrosion initiation. The $Cl_{th}^-$ was increased with increasing Time-to-corrosion ($T_i$). Consequently, the HA(High Alkalinity) specimens exhibited the highest $Cl_{th}^-$ and the NA(Normal Alkalinity) was the least. This range exceeds what has previously been reported in North America. In addition, the effective diffusion coefficient, $D_e$, was about 40 percent lower for concrete prepared with the HA cement compared to the NA and LA(Low Alkalinity) ones.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 추계 학술논문 발표대회
• /
• pp.107-108
• /
• 2011

The purpose of present study is to examine the application of effective curing to hardener-free epoxy-modified mortars. The epoxy-modified mortars are prepared with polymer-cement ratios, subjected to two types of curing conditions, and tested for compressive, flexural and tensile strengths. As a result, hardener-free epoxy-modified mortars with steam curing is markedly improved with increasing air-dry curing period. High strength development of the epoxy-modified mortars may be achieved by the dense microstructure by cement and the hardener of the epoxy resin in the mortars.

• Computers and Concrete
• /
• 제4권2호
• /
• pp.157-166
• /
• 2007

The paper considers a theoretical model to study sulfate ion diffusion in saturated porous media - cement based mineral composites, accounting for simultaneous effects, such as filling micro-capillaries (pores) with ions and chemical products and liquid push out of them. Pore volume change and its effect on the distribution of ion concentration within the specimen are investigated. Relations for the distribution of the capillary relative radius and volume within the composite under consideration are found. The numerical algorithm used is further completed to consider capillary size change and the effects accompanying sulfate ion diffusion. Ion distribution within the cross section and volume of specimens fabricated from mineral composites is numerically studied, accounting for the change of material capillary size and volume. Characteristic cases of 2D and 3D diffusion are analyzed. The results found can be used to both assess the sulfate corrosion in saturated systems and predict changes occurring in the pore structure of the composite as a result of sulfate ion diffusion.

• International Journal of Concrete Structures and Materials
• /
• 제8권4호
• /
• pp.327-333
• /
• 2014

The objective of this work was to examine the influence of carbonation on the microstructure of cement materials. Different materials, which were CEM I mortar and paste, CEM II mortar and paste, were carbonated at $20^{\circ}C$, 65 % relative humidity and 20 % of $CO_2$ concentration. The specific surface area and pore size distribution were determined from two methods: nitrogen adsorption and water adsorption. The results showed that: (1) nitrogen adsorption and water adsorption do not cover the same porous domains and thus, we observed conflicts in the results obtained by these two techniques; (2) the CEM II based materials seemed to be more sensible to a creation of mesoporosity after carbonation than the CEM I based materials. The results of this study also helped to explain why observations in the literature diverge greatly on the influence of carbonation on specific surface area.

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2007년도 제34회 시멘트 심포지엄
• /
• pp.129-137
• /
• 2007

This paper presents a numerical model which can predict degree of hydration of cement mineral component, such as $C_{3}S$, $C_{2}S$, $C_{3}A$, $C_{4}AF$ and microstructure of hydrating cement as a function of water to cement ratio, cement particle size distribution, cement mineral components and temperature. In this model cement particles are parked randomly in cell space and hydration process is described using a multi-component integrated kinetic model. The simulation result of degree of hydration of cement mineral component agrees well with experiment result. The content of cement hydration product, such as CSH and CH can be obtained as an accompanied result during hydration process. By introducing of equal-area projection method, water withdrawl mechanism and contact area among cement particles can be considered in detail. By using proposed method, pore size distribution of hydrating cement is predicted.

• Computers and Concrete
• /
• 제7권1호
• /
• pp.17-38
• /
• 2010

This research aimed to investigate the influence of high-volume mineral admixtures (MAs), i.e., fly ash and slag, on the hydration characteristics and microstructures of cement pastes. Degree of cement hydration was quantified by the loss-on-ignition technique and degree of pozzolanic reaction was determined by a selective dissolution method. The influence of MAs on the pore structure of paste was measured by mercury intrusion porosimetry. The results showed that the hydration properties of the blended pastes were a function of water to binder ratio, cement replacement level by MAs, and curing age. Pastes containing fly ash exhibited strongly reduced early strength, especially for mix with 45% fly ash. Moreover, at a similar cement replacement level, slag incorporated cement paste showed higher degrees of cement hydration and pozzolanic reaction than that of fly ash incorporated cement paste. Thus, the present study demonstrates that high substitution rates of slag for cement result in better effects on the short- and long-term hydration properties of cement pastes.

• 한국세라믹학회지
• /
• 제36권2호
• /
• pp.130-135
• /
• 1999

고로슬래그 시멘트의 저온 조기 강도를 증진키 위하여 고로슬래그의 분말도를 높이고 낮은 물:시멘트 비(W/C)의 혼합수량을 사용하였다. 분쇄조제를 사용하여 6,280$\textrm{cm}^2$/g(Blaine)로 미분쇄한 고로슬래그를 일반 포틀랜드 시멘트와 혼합하여 고로슬래그 40%의 고로슬래그 시멘트를 만들었다. 그리고 시판의 naphthalene계 고성능감수제를 사용하여 혼합수량을 W/C=0.50(KS L 5105)에서 W/C=0.33으로 저하시킬 수 있었다. 상술한 방법을 통하여 고로슬래그 시멘트의 저온 조기 강도를 포트랜드 시멘트 강도보다 오히려 더 높게 향상시킬 수 있었으며, 기공구조 및 임피던스 분석의 방법으로 본 시멘트의 미세구조를 조사하였다.

• 한국건설순환자원학회논문집
• /
• 제10권2호
• /
• pp.159-167
• /
• 2022

본 연구에서는 보통 포틀랜드시멘트를 사용한 콘크리트와 광물질 혼화재료 및 알칼리활성화제를 첨가한 4종류의 배합으로 시편을 제작한 후 X선 회절분석, 미세구조분석, 압축강도, 동결융해저항성 및 SEM Image 분석을 실시하여 각 배합별 강도발현, 상대동탄성계수, 중량변화 등을 측정하여 기초물성 평가를 진행하였다. 페로니켈슬래그 혼입 삼성분계 시멘트는 보통포틀랜드 시멘트 배합(OPC)과 비슷한 수화물을 생성하는 경향을 보였으며, MgO 성분으로 인한 팽창성 수화물은 확인되지 않았다. 페로니켈슬래그를 혼입 시 3성분계 시멘트(30SP20FN)의 경우 OPC와 비교 시 공극률이 커지는 경향을 보였지만, 알칼리활성화제를 첨가할 경우 공극 분포가 변화하는 경향을 보였다. 또한, 알칼리활성화제의 첨가는 30SP20FN의 장기강도발현을 앞당기는 효과를 보였으며, 18~26 % 가량 강도가 증가함을 확인하였다. 30SP20FN의 경우 dilution effect로 인한 낮은 수화도의 영향으로 동결융해저항성이 떨어졌지만, 알칼리활성화제를 첨가할 경우 높은 상대동탄성계수를 유지하였으며, 동결융해 저항성이 우수한 것을 알 수 있었는데, 이는 변화된 공극 분포 때문인 것으로 사료된다. 본 연구에서 실시한 상대동탄성계수 측정 실험에 사용된 콘크리트 시편 모두 300 사이클에서 상대동탄성계수가 60 % 이상으로 우수한 동결융해 저항성을 나타내었다. 동결융해 작용을 받은 콘크리트의 미세구조를 분석한 결과, OPC 및 30SP20FN 콘크리트의 경우 비정질의 수화물이 서로 결합되어 있지 않고, 미세 균열이 발생함을 확인한 반면, 알칼리 활성화제를 혼입한 배합의 경우 균질한 내부 구조를 유지하였다.