• 한국분말재료학회지
• /
• 제12권2호
• /
• pp.146-150
• /
• 2005

An optimum route to synthesize $Al_2O_3$-based composite powders with homogeneous dispersion of carbon nanotubes (CNTs) was investigated. CNTs/Metal/$Al_2O_3$ nanocomposite powders were fabricated by thermal chemical vapor deposition of $C_2H_2$ gas over metal/$Al_2O_3$ nanocomposite catalyst prepared by selective reduction of metal oxide/$Al_2O_3$ powders. The FT-Raman spectroscopy analysis revealed that the CNTs have single- and multi-walled structure. The CNTs with the diameter of 25-43 nm were homogeneously distributed in the metal/$Al_2O_3$ powders, and their characteristics were strongly affected by a kind of metal catalyst and catalyst size. The experimental results show that the composite powder with required size and dispersion of CNTs can be realized by control of synthesis condition.

• 한국응용과학기술학회지
• /
• 제37권4호
• /
• pp.723-732
• /
• 2020

RHDS 촉매는 코크와 황 화합물 그리고 금속인 바나듐이 표면에 침적되어 비활성화가 된다. 이러한 오염물을 제거하기 위해서 먼저 폐 RHDS 촉매에 묻어있는 중질유분의 세정, 코크와 황 화합물을 고온 배소 처리한 후, 과량으로 침적되어 있는 바나듐의 침출량을 조절하기 위하여 0.5, 1 wt% 옥살산 수용액을 이용하여 초음파 교반기에서 50 ℃, 10 sec 동안 교반하여 NOx 저감을 위한 SCR 촉매로의 적용 가능성을 확인하고자 하였다. 재생처리 한 RHDS 촉매의 성분은 XRF 를 사용하여 분석하였고, 상압 고정층 연속 흐름 반응기 상에서 NOx 저감 성능을 측정하였다. 옥살산 수용액 0.5 wt%, 10 sec 동안 초음파 침출한 촉매가 가장 안정적인 NOx 저감 성능을 보였으며, 375 ℃ 이상의 고온에서는 상용 촉매와 동등 수준의 NOx 저감 성능을 확인할 수 있었으나 저온영역 200 ℃에서 250 ℃까지는 상용 촉매보다 낮은 NOx 저감 성능을 보였다. 따라서 폐 RHDS 촉매를 재생처리 한 후 분말로 메탈 코로게이트 지지체에 워시코팅한 촉매는 상용 SCR 촉매로서 이용 가능함을 확인하였다.

• 대한환경공학회지
• /
• 제34권6호
• /
• pp.397-405
• /
• 2012

본 연구는 휴대폰을 비롯한 전자제품 세척공정과 악취유발물질 등에서 배출되는 휘발성 유기화합물(VOCs)을 경제적이고 안전하게 제거하는 기술에 대한 성능평가를 위해 수행되었다. 대부분의 산업공정에서는 VOCs 제거를 위해 활성탄 흡착탑을 가장 많이 사용하고 있으나 제거효율이 낮아 악취배출시설의 허용기준을 만족할 수 없고, 고농도 유기용제 유입 시 화재위험이 있다. 지금까지 연구되어진 금속산화물 촉매는 VOCs 제거효율이 최소 $220^{\circ}C$ 근방에서 50% 이하였다. 본 연구에서는 이 보다 훨씬 낮은 온도인 $100^{\circ}C$ 이하에서 촉매산화가 시작되었고, 약 $160^{\circ}C$ 근방에서 VOCs가 95% 제거됨을 확인할 수 있었다. 적정처리가 가능한 범위는 공간속도가 $6,000hr^{-1}$ 이하일 때 최적의 제거효율을 나타내며, VOCs 유입농도가 200 ppm에서 4,000 ppm 사이, 촉매제어 온도가 $150{\sim}200^{\circ}C$에서 90~99%로 높은 제거효율을 보였고, VOCs 유입농도가 1,000 ppm 이상일 경우에는 자체반응열로 인해 외부열원이 필요 없었다. 본 저온촉매를 적용할 경우 LNG 와 LPG를 연료원으로 사용하는 RTO/RCO방식 대비 설치비는 50%, 연료비는 75% 감소되어 경제성이 높고 온실가스 발생량도 줄일 수 있었다. 그리고 황화합물과 산성가스에 대해서는 피독이 있는 것으로 확인되었다.

• 한국재료학회지
• /
• 제15권3호
• /
• pp.189-194
• /
• 2005

[ $SiO_2$ ] nanowires were synthesized using the catalyst evaporation method. Grown nanowires had different shapes by kind of used metal catalyst. Mean diameters of grown $SiO_2$ nanowire were about 30 nm. The kind of catalysts affected microstructure of grown $SiO_2$ nanowire because of its typical growth reactions through the liquid state metal catalysts. Optical property were measured by photoluminescence spectroscopy. Relatively broad peak was obtained and mean peak positioned at 450 nm.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.514-517
• /
• 2008

Water gas shift(WGS) is an important step in fuel process for fuel cells, and improperness of commercial WGS catalysts for use in fuel cell systems has prompted numerous researches on noble metal catalysts. A selected noble metal catalyst for water gas shift reaction(WGS) was prepared with various metal loadings. The prepared catalysts were tested under two feeding conditions. At moderate residence time, carbon monoxide conversion was much higher on the noble metal catalysts as compared to commercial high-temperature shift catalyst. Effects of metal loading were examined by activity tests at short residence time. Higher metal loading effected higher reaction rate. The kinetic data was fitted to simple reaction equations and effectiveness factor was estimated. The results suggest the necessity of a structural design for the highly active noble metal catalysts.

• 한국대기환경학회지
• /
• 제16권5호
• /
• pp.529-537
• /
• 2000

Several Pt-based oxidation catalysts with different loading were prepared with various metal precursor solutions and characterized with H$_2$ chemisorption and TEM for Pt particle size. V was added to Pt-based catalyst for inhibiting SO$_2$oxidation reaction, as result, Pt-V/Ti-Si catalyst prepared by ERMS(Free Reduced Metal in Solution) method showed high enough activity and better inhibition on SO$_2$oxidation than Pt only catalyst. Optimum Pt particle size for diesel oxidation reaction turned out to be the size of around 20 nm. A prototype catalyst was prepared for light=duty diesel passenger car, and teated for the emission reduction performance with Korean regulation test mode(CVS-75 mode) on chassis dynamometer. The catalyst shows the performance reduction of 75~94% for CO, 53~67% for HC and 10~31% for PM. In the case of heavy-duty diesel catalyst, the domestic formal regulation teat mode D-13 was adopted for both Na engine and Turbo engine. The conversions of CO and THC are high enough(86% and 41%) while the reductions of NOx and PM are relatively low(3~11%).

• 자원리싸이클링
• /
• 제10권3호
• /
• pp.23-28
• /
• 2001

Magnetite가 주성분인 산화철 폐촉매를 이용하여 도금폐수중 아연이온을 pH 2.0이상에서 98.7% 이상 회수하였다. 폐촉매의 포화자화값은 59.4 smug으로 폐수처리후 자기적방법에 의해 고.액분리가 가능하다. 산화철 .폐촉매에 의한 폐수중 아연이온의 회수메카니즘은 pH 3.0-8.5 범위에서는 폐촉매 표면에서 $Zn^{2+}$ 이온의 정전기적 흡착이며 pH 8.5 이상에서는 $Zn(OH)_2$의 침전이라고 생각한다.

• Environmental Engineering Research
• /
• 제18권3호
• /
• pp.145-150
• /
• 2013

Optimal preparation guidelines of a cathode catalyst layer by non-precious metal catalysts were evaluated based on electrochemical performance in single-chamber microbial fuel cells (MFCs). Experiments for catalyst loading rate revealed that iron(II) phthalocyanine (FePc) can be a promising alternative, comparable to platinum (Pt) and cobalt tetramethoxyphenylporphyrin (CoTMPP), including effects of substrate concentration. Results showed that using an optimal FePc loading of $1mg/cm^2$ was equivalent to a Pt loading of $0.35mg/cm^2$ on the basis of maximum power density. Given higher loading rates or substrate concentrations, FePc proved to be a better alternative for Pt than CoTMPP. Under the optimal loading rate, it was further revealed that 40 wt% of FePc to carbon support allowed for the best power generation. These results suggest that proper control of the non-precious metal catalyst layer and substrate concentration are highly interrelated, and reveal how those combinations promote the economic power generation of single-chamber MFCs.

• 한국응용과학기술학회지
• /
• 제31권2호
• /
• pp.313-319
• /
• 2014

This study was performed to obtain high conversion efficiency of $NH_3$ and minimize generation of nitrogen oxides using metal-supported catalyst with Ag : Cu ratio. Through structural analysis of the prepared catalyst with Ag : Cu ratio ((10-x)Ag-xCu ($0{\leq}x{\leq}6$)), it was confirmed that the specific surface area was decrease with increasing metal content. A prepared catalysts showed Type II adsorption isotherms regardless of the ratio Ag : Cu of metal content, and crystalline phase of $Ag_2O$, CuO and $CuAl_2O$ was observed by XRD analysis. In the low temperature($150{\sim}200^{\circ}C$), a conversion efficiency of AC_10 recorded the highest(98%), whereas AC_5 (Ag : Cu = 5 : 5) also showed good conversion efficiency(93.8%). However, in the high temperature range, the amounts of by-products(NO, $NO_2$) formed with AC_5 was lower than that of AC_10. From these results, It is concluded that AC_5 is more environmentally and economically suitable.

• 한국환경과학회지
• /
• 제15권7호
• /
• pp.635-642
• /
• 2006

Present study evaluated the low-temperature destruction of n-hexane and benzene using mesh-type transition-metal platinum(Pt)/stainless steel(SS) catalyst. The parameters tested for the evaluation of catalytic destruction efficiencies of the two volatile organic compounds(VOC) included input concentration, reaction time, reaction temperature, and surface area of catalyst. It was found that the input concentration affected the destruction efficiencies of n-hexane and benzene, but that this input-concentration effect depended upon VOC type. The destruction efficiencies increased as the reaction time increased, but they were similar between two reaction times for benzene(50 and 60 sec), thereby suggesting that high temperatures are not always proper for thermal destruction of VOCs, when considering the destruction efficiency and operation costs of thermal catalytic system together. Similar to the effects of the input concentration on destruction efficiency of VOCs, the reaction temperature influenced the destruction efficiencies of n-hexane and benzene, but this temperature effect depended upon VOC type. As expected, the destruction efficiencies of n-hexane increased as the surface area of catalyst, but for benzene, the increase rate was not significant, thereby suggesting that similar to the effects of the re- action temperature on destruction efficiency of VOCs, high catalyst surface areas are not always proper for economical thermal destruction of VOCs. Depending upon the inlet concentrations and reaction temperatures, almost 100% of both n-hexane and benzene could be destructed, The current results also suggested that when applying the mesh type transition Metal Pt/SS catalyst for the better catalytic pyrolysis of VOC, VOC type should be considered, along with reaction temperature, surface area of catalyst, reaction time and input concentration.