• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05a
• /
• pp.35-38
• /
• 2005

Carbon fiber sheets are widely used for strengthening the deteriorated RC structures. However most studies on the strengthening method of RC structures with carbon fiber sheets are concerning static problems. The purpose of this experimental study is to present the basic data on fatigue behaviors of. RC beams strengthened with carbon fiber sheets. The experimental parameters of this study are ; 1) the existence of U-shaped carbon fiber sheets at the ends for anchoring, 2) the number of carbon fiber sheet layers in strengthening the RC beams, 3) the load levels of $60\%\~90\%$ of the static bending moment strength, which is obtained form the static tests. Experimental results are estimated from the relationships of load level, displacement, number of repeated load and released energy. It is concluded that U-shaped carbon fiber sheets for end anchoring is very effective and the beams strengthened with one layer of carbon fiber sheet have longer fatigue life than that with three layers.

• Korean Journal of Materials Research
• /
• v.23 no.2
• /
• pp.149-153
• /
• 2013

Delamination crack detection is very important for improving the structural reliability of laminated composite structures. This requires real-time delamination detection technologies. For composite laminates that are reinforced with carbon fiber, an electrical potential method uses carbon fiber for reinforcements and sensors at the same time. The use of carbon fiber for sensors does not need to consider the strength reduction of smart structures induced by imbedding sensors into the structures. With carbon fiber reinforced (CF/) epoxy matrix composites, it had been proved that the delamination crack was detected experimentally. In the present study, therefore, similar experiments were conducted to prove the applicability of the method for delamination crack detection of CF/polyetherethereketone matrix composite laminates. Mode I and mode II delamination tests with artificial cracks were conducted, and three point bending tests without artificial cracks were conducted. This study experimentally proves the applicability of the method for detection of delamination cracks. CF/polyetherethereketone material has strong electric resistance anisotropy. For CF/polyetherethereketone matrix composites, a carbon fiber network is constructed, and the network is broken by propagation of delamination cracks. This causes a change in the electric resistance of CF/polyetherethereketone matrix composites. Using three point bending specimens, delamination cracks generated without artificial initial cracks is proved to be detectable using the electric potential method: This method successfully detected delamination cracks.

• Journal of the Korean Society for Heat Treatment
• /
• v.35 no.2
• /
• pp.51-56
• /
• 2022

In this study, we controlled the shape of a carbon layer on gallium oxide templates. Gallium oxide layers were deposited on sapphire substrates using mist chemical vapor deposition. Subsequently, carbon layers were formed using radio frequency plasma chemical vapor deposition. Various shapes of carbon structures appeared according to the fraction of methane gas, used as a precursor. As methane gas concentration was adjusted from 1 to 100%, The shapes of carbon structures varied to diamonds, nanowalls, and spheres. The growth of carbon isotope structures on Ga₂O₃ templates will give rise to improving the electrical and thermal properties in the next-generation electronic applications.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.294-299
• /
• 2003

We have investigated the structures of copper nanowires encapsulated in carbon nanotubes using a structural optimization process applied to the steepest descent method. The results showed that the stable morphology of the cylindrical ultrathin copper nanowires in carbon nanotubes is multishell packs consisted of coaxial cylindrical shells. As the diameter of copper nanotubes increased, the encapsulated copper nanowires have the face centered cubic structure as the bulk. Both the semiclassical orbits in a circle and the circular rolling of a triangular network can explain the structures of ultrathin multishell copper nanowires encapsulated in carbon nanotubes.

• Journal of Ocean Engineering and Technology
• /
• v.14 no.1
• /
• pp.52-59
• /
• 2000

Flexural fracture characteristics of newly-developed Grid-type carbon fiber plastics in the deteriorated reinforced concrete structures were investigated by the four-points fracture test to verify the strengthening effects in the beam specimens. Results showed that initial cracks appeared in the boundary layers of fibers embedded in the newly-placed mortar concrete slowly progressed to the direction of supports and showed fracture of fiber plastics and brittle failure of concrete in compression in sequence after the yielding of steel reinforcement. Accordingly the reasonable area of Grid-type carbon-fiber plastics in the strengthening design of deteriorated RC structures should be limited and given based on the ultimate strength design method to avoid the brittle failure of concrete structures.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.119-122
• /
• 2004

A CPGFRP(Carbon Powder Glass Fiber Reinforced Plastics) sensor was fabricated for fine crack detection of structures. The electrical resistance of the sensor was measured on condition of various composition of carbon powders and thickness of bundle of glass fibers. The resistance was decreased as the increase of the content of carbon powders and the TEX of the glass fibers. In the case of loading on CPGFRP sensor, because inner crack was propagated, the part of percolation structures was disconnected. The sensor is superior to carbon fiber for the detecting ability of fine crack.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.266-266
• /
• 2012

Ni films with a thickness of 700-800 nm were deposited on carbon fiber layers using electroless deposition, and surface structures and chemical properties of these films with various annealing temperatures (300, 600 and $900^{\circ}C$) were studied. $600^{\circ}C$-annealing under atmospheric conditions resulted in formation of porous surface structures with a mean pore size of ~100 nm, whereas the other samples showed non-porous surface structures. $600^{\circ}C$-annealed Ni film showed much higher reactivities for toluene adsorption and CO oxidation comparing to other non-porous surfaces.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.131-134
• /
• 2004

The object of this study is to design the Radar Absorbing Structures (RAS) having sandwich structures in the X-band $(8.2\~12.4GHz)$ frequencies. Glass fabric/epoxy composites containing conductive carbon blacks and carbon fabric/epoxy composites were used for the face sheets. Polyurethane (PU) foams containing multi­walled carbon nanotube (MWNT) were used for the core. Their permittivities in the X-band were measured using the transmission line technique. The reflection loss characteristics for multi-layered sandwich structures were calculated using the theory of transmission and reflection in a multi-layered medium. Three kinds of specimens were fabricated and their reflection losses in the X-band were measured using the free space technique. Experimental results were in good agreements with simulated ones in 10dB absorbing bandwidth.

• Journal of Korean Association for Spatial Structures
• /
• v.23 no.3
• /
• pp.105-113
• /
• 2023

The study used the whole-life carbon assessment method to conduct a thorough carbon-neutral evaluation of a standard steel structure. To further assess carbon emissions, 11 design-changed models were evaluated, with changes made to the span between beams and columns. The results of the carbon emission assessment showed savings of approximately 13.1% by implementing the stage of the beyond life cycle. Additionally, the evaluation of carbon emissions through design changes revealed a difference of up to 42.2%. These findings confirmed that recycling and structural design changes can significantly reduce carbon emissions by up to 48.6%, making it an effective means of achieving carbon neutrality. It is therefore necessary to apply the stage of beyond life cycle and structural change to reduce carbon emissions.

• Journal of the Korean Ceramic Society
• /
• v.40 no.12
• /
• pp.1150-1153
• /
• 2003

Carbon nanofilaments were formed on silicon substrate using microwave plasma-enhanced chemical vapor deposition method. The structures of carbon nanofilaments were identified as carbon nanotubes or carbon nanofibers. The formation of bamboo-like carbon nanotubes was initiated by the application of the bias voltage during the plasma reaction. The growth kinetics of bamboo-like carbon nanotubes increased with increasing the bias voltage. The growth direction of bamboo-like carbon nanotubes was vertical to the substrate.