• Journal of Ceramic Processing Research
• /
• 제19권6호
• /
• pp.479-482
• /
• 2018

Polystyrene superstructure films show faint rainbow color, and this low color saturation limits its wide application. In this paper, polystyrene superstructure films with single bright blue color were prepared by vertical deposition self-assembly method using polystyrene microspheres with average diameter of $310{\pm}10nm$ as raw material. Polystyrene superstructure films were modified by adding nano-carbon powder, and effect of the amount of nano-carbon powde on color performance was studied. The results showed that without addition of nano-carbon powder, the superstructure films showed a faint rainbow color, while with addition of nano-carbon power, the superstructure films exhibited a single bright blue under the same natural light source. Changing the amount of nano-carbon powder addition could adjust color saturation of the film. With increasing the amount of nano-carbon powder addition from 0.008 wt% to 0.01 wt%, color saturation of the superstructure film increased gradually. Further increasing the amount of nano-carbon powder addition to 0.011wt%, color saturation of the superstructure film didn't increase anymore and tended to get dark.

• Carbon letters
• /
• 제2권3_4호
• /
• pp.165-169
• /
• 2001

Modification of C/C composite bipolar plate for improving electrical conductivity was carried out by addition of electroconductive carbon black (EC-CB). Carbon black was carefully mixed to methanol-containing phenolic resin, impregnated into 2D-carbon fabrics, hot pressed and then carbonized to obtain composite plate. Inclusion of electro-conductive carbon black enhanced the electrical conductivity of the C/C composites by increasing the conduction path. Addition of 10 vol% carbon black increased the electrical conductivity from 5.5/${\Omega}cm$ to 32/${\Omega}cm$ and reduced the crack formation by filling effect, resulting in the increase of flexural properties of composite plate. However, at carbon black content over 10 vol%, flexural properties decreased by delaminating role of excess carbon black at the interface in C/C composites.

• 한국표면공학회지
• /
• 제14권3호
• /
• pp.142-150
• /
• 1981

The present paper clarified mechanism of quench crack formation in high carbon steel dur-ing quenching, and, in order to prevent the quench crack, proposed two basic guides in alloy design of high carbon tool steel. They are to raise Ms temperature of high carbon tool steel by addition of alloying elemen-ts such as Al and Co, and to decrease grain size of the carbon tool steel by addition of alloying elements of Al, B, Ti, Zr, and V, and by grain-refining heat treatment.

• 열처리공학회지
• /
• 제28권1호
• /
• pp.1-6
• /
• 2015

The ductile-to-brittle transition behavior of two austenitic Fe-18Cr-10Mn alloys with the combined addition of nitrogen and carbon was investigated in this study. The alloys exhibited a ductile-to-brittle transition behavior because of unusual brittle fracture at low temperatures unlike conventional austenitic alloys. The alloy with higher carbon content had higher yield and tensile strengths than that with lower carbon content due to the solid solution strengthening effect resulting from carbon addition. However, the increase in carbon content promoted the occurrence of intergranular fracture, and thus deteriorated the impact toughness. In order to develop successfully the austenitic Fe-18Cr-10Mn alloys with the excellent combination of strength and toughness in the future, therefore, more systematic studies are required to find the appropriate amount and ratio of nitrogen and carbon.

• Bulletin of the Korean Chemical Society
• /
• 제25권10호
• /
• pp.1521-1524
• /
• 2004

The effect of $H_2$ gas on the carbon nanotubes (CNTs) synthesis with CO-$H_2$ gas mixture was investigated using mass measurements and scanning electron microscopy (SEM). The maximum weight and yield of the synthesized carbon were obtained when the mixture ratio of $H_2$: CO was 3 : 7 and 9 : 1, respectively. In case of 100% carbon monoxide (CO) without hydrogen ($H_2$) addition, the weight of carbon increased, but CNTs were not observed. The CNTs began to be made when the contents of $H_2$ reaches at least 10%, their structures became more distinct with an increase of $H_2$ addition, and then the shapes of CNTs were more thin and straight. When the contents of $H_2$ was 80% ($H_2$ : CO = 8 : 2), the shapes and growth of CNTs showed an optimal condition. On the other hand, when the contents of $H_2$ was higher than the critical value, the shapes of CNTs became worse due to transition into inactive surface of catalyst. It was considered that the inactive surface of catalyst resulted from decrease of carbon (C) and $H_2$ concentration by facilitation of methane ($CH_4$) gasification reaction (C + 2$H_2$ ${\rightarrow}$ $CH_4$) between C and $H_2$ gases. It was also found that H2 addition had an influence considerably on the shape and structure of CNTs.

• 열처리공학회지
• /
• 제10권2호
• /
• pp.101-108
• /
• 1997

In high carbon steels, the cementite phase is more unstable thermally than graphite, and it can lead to a marked deterioration in the formability. Many studies have been carried out to evaluate the effect of the fundamental elements on the graphitization of cementite in high carbon steels. In this present work, the effect of Mn, Cr addition on graphitization in Fe-0.65%C-1.0%Si steel has been investigated by means of hardness testing, optical microscopy and EPMA. The nucleation of graphite may mostly depend on the dissolution rate of cementite into ferrite and the number of the nucleation sites of graphite. The graphitization was promoted by the addition of 0.1%Mn in high carbon steel, but retarded by more addition than 0.5% of Mn. By the more addition of Cr than 0.1%, the graphitization of high carbon steel was strongly retarded. Because Mn was moderate anti-graphitizer, but Cr was stroug anti-graphitizer.

• 한국재료학회지
• /
• 제24권9호
• /
• pp.488-494
• /
• 2014

The effect of tungsten (W) addition on the hardenability of low-carbon boron steels was investigated using dilatometry, microstructural observations and secondary ion mass spectroscopy. The hardenability was discussed with respect to transformation behaviour aspects depending on the segregation and precipitation of boron at austenite grain boundaries. A critical cooling rate producing a hardness corresponding to 90 % martensite structure was measured from a hardness distribution plot, and was used as a criterion to estimate hardenability at faster cooling rates. In the low-carbon boron steel, the addition of 0.50 wt.% W was comparable to that of 0.20 wt.% molybdenum in terms of critical cooling rate, indicating hardenability at faster cooling rates. However, the addition of 0.50 wt.% W was not more effective than the addition of .0.20 wt.% molybdenum at slower cooling rates. The addition of 0.20 wt.% molybdenum completely suppressed the formation of eutectoid ferrite even at the slow cooling rate of $0.2^{\circ}C/s$, while the addition of 0.50 wt.% W did not, even at the cooling rate of $1.0^{\circ}C/s$. Therefore, it was found that the effect of alloying elements on the hardenability of low-carbon boron steels can be differently evaluated according to cooling rate.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 영호남학술대회 논문집
• /
• pp.149-154
• /
• 2000

In this paper, we studied the relation between addition of carbon and electromagnetic wave absorbing properties of ferrite-rubber composite. The ratio of carbon was 7 wt%. As s result, it has been shown that the electromagnetic wave absorbing properties of ferrite-rubber composite are changed by the addition of carbon in composite. And, we can control electromagnetic wave absorbing properties of ferrite-rubber composite by the using of carbon.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.557-558
• /
• 2006

In all conventional sintered PM products, the pores present are of two types, primary and secondary. Primary pores forming during compaction and latter during sintering, due to penetration of formed liquid through the matrix grain boundary. Effect of carbon addition on diffusion of Cu in SH737-2Cu system was investigated. After compaction and transient liquid phase sintering at $1120^{\circ}C$ and $1180^{\circ}C$, samples were characterized for densification, showing rise in sintering density and reduction in swelling on carbon addition. Quantitative microstructural characterization (shape factor and pore size) revealed bimodal distribution for 0% carbon, more rounded pores for 0.9% carbon and higher sintering temperature, and pore coarsening at higher sintering temperature.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1998년도 한국재료학회 춘계학술발표강연 및 논문개요집
• /
• pp.105-105
• /
• 1998