• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권6호
• /
• pp.733-740
• /
• 2014

A resistive micro Pirani gauge using amorphous silicon (a-Si) thin membrane is proposed. The proposed Pirani gauge can be easily integrated with the other process-compatible membrane-type sensors, and can be applicable for in-situ vacuum monitoring inside the vacuum package without an additional process. The vacuum level is measured by the resistance changes of the membrane using the low noise correlated double sampling (CDS) capacitive trans-impedance amplifier (CTIA). The measured vacuum range of the Pirani gauge is 0.1 to 10 Torr. The sensitivity and non-linearity are measured to be 78 mV / Torr and 0.5% in the pressure range of 0.1 to 10 Torr. The output noise level is measured to be $268{\mu}V_{rms}$ in 0.5 Hz to 50 Hz, which is 41.2% smaller than conventional CTIA.

• 센서학회지
• /
• 제23권5호
• /
• pp.326-331
• /
• 2014

In this study, a MEMS microphone that uses $Si_3N_4$ as the vibration membrane was produced for application as an auditory device using a sound visualization technique (sound visualization) for the hearing impaired. Two sheets of 6-inch silicon wafer were each fabricated into a vibration membrane and back plate, after which, wafer bonding was performed. A certain amount of charge was created between the bonded vibration membrane and the back plate electrodes, and a MEMS microphone that functioned through the capacitive method that uses change in such charge was fabricated. In order to evaluate the characteristics of the prepared MEMS microphone, the frequency flatness, frequency response, properties of phase between samples, and directivity according to the direction of sound source were analyzed. The MEMS microphone showed excellent flatness per frequency in the audio frequency (100 Hz-10 kHz) and a high response of at least -42 dB (sound pressure level). Further, a stable differential phase between the samples of within -3 dB was observed between 100 Hz-6 kHz. In particular, excellent omnidirectional properties were demonstrated in the frequency range of 125 Hz-4 kHz.

• International Journal of Internet, Broadcasting and Communication
• /
• 제7권2호
• /
• pp.73-78
• /
• 2015

Touch panel is mainly applied to pressure type touch panel but it occur a low recognition rate and error during long-term use. So, it is partly applied to capacitive touch panel to compensate for these problems but it also can occur a same problems via pollutions. Touch technology has developed a various method but it is not used because of high costs and difficult installation process. So, in this paper, we proposed an input method of touchless panel using IrDA matrix. This method is conducted using an IrDA Matrix composed of depth sensor. It is possible to offer a various contents for multi user. The proposed technology need a development of a high sensitivity sensing method and high-speed processing method of position information for Seamless operation control. And, it is required high-precision drive technology. Also, we proposed a Seamless user recognition for interactive contents service through a touchless panel using IrDA matrix.

• 한국자동차공학회논문집
• /
• 제13권6호
• /
• pp.13-20
• /
• 2005

The most typical fuel control devices of motorcycle engines have carburetors, they are simple in structure and reliable in work. Most of the motorcycle engines have used carburetors in the fuel system, but the fuel economy and the emissions of those engines are bad when we compared with automobile engines. According to stricter emission regulations and higher requirements for fuel economy, the application of the carburetor on the motorcycle engines would be limited. In this paper, we studied about the ECU of motorcycle engine controled by indirect method. A new engine system was designed and experiments were carried out. The experimental results for both carburetor type and ECU type were compared. Maximum torque of $1.053kg{\cdot}m$ at 6500rpm was measured. The engine torque controled using ECU was increased by $10\%$ compared with the carburetor type.

• 대한전자공학회논문지SD
• /
• 제49권2호
• /
• pp.1-8
• /
• 2012

본 논문은 자동차용 타이어 공기압 모니터링 시스템(TPMS)의 핵심 부품인 가속도센서에 관한 연구이다. 일반적으로 압저항형 가속도센서는 정전용량형 가속도센서에 비하여 제조 비용이 적고 출력 특성이 선형적이며 주변 잡음에 면역성이 강한 장점을 갖는다. 그래서 TPMS용으로 압저항형을 선택하였고, ANSYS 프로그램을 이용하여 3가지 타입의 구조를 설계하여 공진주파수 특성을 비교하여 가장 안정적인 구조인 질량체 가장자리의 가운데에 있는 4개의 빔에 의하여 지지되는 브릿지 타입의 실리콘압저항형 가속도센서를 선택하였다. 그리고 센서 크기를 고려하여 빔의 길이는 $200{\mu}m$로 정하였으며, 빔 길이에 따른 최대응력과 최대변위를 시뮬레이션하여 센서를 설계하였다. TPMS용 4 빔 실리콘 미세 압저항형 가속도센서의 크기는 $3.0mm{\times}3.0mm{\times}0.4mm$의 크기로 제작 되었다. 휠 각도에 따른 출력 특성과 온도 특성을 측정하여 센서의 특성을 분석 하였다. 그 결과 가속도센서의 옵셋 전압은 43.2 mV 이고 감도는 $42.5{\mu}V/V/g$ 이다. 센서의 특징으로 내충격성은 1500 g 이고, 측정 범위는 0 ~ 60 g, 사용온도는 $-40^{\circ}C{\sim}125^{\circ}C$ 를 갖는다.