• 한국군사과학기술학회지
• /
• 제15권3호
• /
• pp.231-240
• /
• 2012

During the past two decades, Metal Injection Molding(MIM) has become a very competitive technology to fabricate small, precise and complex-shaped parts in large quantities. In this research, the applicability of MIM technology in the mass-production of the high precision fuze parts to save manufacturing cost was investigated. The water-atomized 17-4PH stainless steel powder, one of the best corrosion-resistant high strength materials, was injection-molded into real-shape fuze part and flat tensile specimens. The injection-molded parts were thermally debound in hydrogen gas flow without solvent extraction. Sintering of the debound parts was carried out in vacuum at temperatures ranging from $1150^{\circ}C$ to $1370^{\circ}C$. The sintering behavior, mechanical properties, dimensional precision, corrosion resistance of the MIMed 17-4PH stainless parts were investigated. It was found that almost all the properties of the MIMed parts were comparable to those of the mechanically machined parts. Also, actual military field tests using both MIMed and mechanically machined fuze parts were performed as well and were found to be very successful.

• Fisheries and Aquatic Sciences
• /
• 제3권1호
• /
• pp.1-7
• /
• 2000

Different substrata fixed as the roof (for shadow) on artificial iron reef had been developed as a tool for valuable fishery resources. The experiment was set up on a sandy bottom substratum at 8m depth in Muronohana, Ikata, Japan. Within one month of placement of the plates, diatoms dominated the experimental plates with a coverage of $100\%$ approximately. Enteromorpha intestinalis and Colpomenia sinuosa dominated within three months after the placement. E. intestinalis coverage on substrata was estimated $7\%$ on the plate shaped iron bar, $12-14\%$ on concrete plates, $18\%$ on the plate fixed pebble, $61\%$ on the plate to accumulated wood, and 80-100% on the steel materials plate. Whereas after four months of placement, C. sinuosa coverage on plates became $1-36\%$ on different plates, and $100\%$ on the plate to accumulated wood. The differences in E. intestinalis and C. sinuosa colonization on the different substrata were probably due to variations in their surface roughness influencing the settlement of zoospores, and thus gametophyte. development. After five months of placement, the above two species slowly disappeared.

• 열처리공학회지
• /
• 제22권3호
• /
• pp.162-168
• /
• 2009

A horizontal tube furnace with a wide uniform-temperature zone was developed using isothermal characteristics of a heat pipe. The heat pipe heating system consists of a concentric annular shaped stainless-steel container, sodium as a working fluid and a screen mesh wick structure. The performance test of the heat pipe revealed that temperature changes along seven consecutive positions of the heat pipe outer wall were less than${\pm}0.1^{\circ}C$, thereby ensuring the high isothermal property. The isothermal property of the heat pipe-adapted tube fumace was investigated and compared to a conventional non-heat pipe type tube furnace. The temperature distribution measurement showed that the uniform temperature zone, in which temperature change is less than${\pm}$1$^{\circ}$C, of the heat pipe employed tube furnace system was about three times longer compared to the conventional tube furnace system.

• 한국강구조학회 논문집
• /
• 제29권2호
• /
• pp.111-122
• /
• 2017

본 연구에서는 1900mm급의 춤이 깊은 콘크리트 채움 U형 메가 합성보의 합성보통모멘트골조에 대한 적용성을 검토하였다. 대형 합성보의 실물대 내진성능실험에 대한 현실적 제약으로 인하여 작은 규모의 실험체에 대해 수행된 기존 실험결과의 분석과 수치해석연구의 보완을 통해 연구를 수행하였다. 이러한 형태의 합성보는 부모멘트 작용시의 웨브국부좌굴이 가장 중요하므로 선행 실물대 실험결과로부터 웨브의 판폭두께비와 층간변형능력 사이의 관계를 분석하였다. 그 결과, 25mm 두께의 U형 강재단면을 지닌 1900mm급의 대형 합성보라 하더라도 층간변위각 2% 이후 웨브국부좌굴을 경험하고 3% 이후 최대변형에 도달하는 것으로 확인되었다. 이는 합성보통모멘트골조의 요구조건을 상회하는 것으로 AISC 기준에 따른 웨브 판폭두께비 제한이 본 연구의 U형 단면에는 보수적임을 시사하기도 한다. 유한요소해석을 통해서는 합성보의 휨성능 및 웨브국부좌굴에 대한 수평스티프너의 영향을 분석하였다. 대형 합성보는 스티프너 보강과 관련없이 부모멘트 방향으로 공칭소성모멘트 이상의 휨성능을 발휘하였으며, 스티프너를 보강할 경우에는 웨브국부좌굴이 상당히 지연되는 긍정적인 효과가 있었다. 이상의 실험결과 분석 및 해석연구에 의하면 1900mm급의 춤이 깊은 콘크리트 채움 U형 메가 합성보는 합성보통모멘트골조에 보수적으로 적용가능한 것으로 판단된다.

• Smart Structures and Systems
• /
• 제31권3호
• /
• pp.213-227
• /
• 2023

A passive prismatic-shaped isolation platform (PIP) is proposed to realize enhanced quasi-zero stiffness (QZS) effect. The design concept uses a horizontal spring to produce a tunable negative stiffness and installs oblique springs inside the cells of the prismatic structure to provide a tunable positive stiffness. Therefore, the QZS effect can be achieved by combining the negative stiffness and the positive stiffness. To this aim, firstly, the mathematical modeling and the static analysis are conducted to demonstrate this idea and provide the design basis. Further, with the parametric study and the optimal design of the PIP, the enhanced QZS effect is achieved with widened QZS range and stable property. Moreover, the dynamic analysis is conducted to investigate the vibration isolation performance of the proposed PIP. The analysis results show that the widened QZS property can be achieved with the optimal designed structural parameters, and the proposed PIP has an excellent vibration isolation performance in the ultra-low frequency due to the enlarged QZS range. Compared with the traditional QZS isolator, the PIP shows better performance with a broader isolation frequency range and stable property under the large excitation amplitude.

• Journal of Biosystems Engineering
• /
• 제35권2호
• /
• pp.108-115
• /
• 2010

This study was conducted to estimate the optimum temperature and required time for soil sterilization when heated water was circulated through underground heating pipes in the greenhouse which solar heat was influenced to the temperature of soil during the summer day. Two different types of heating pipes were used for the experiment. One was a polyethylene pipe(XL) and the other was a corrugated ring shaped stainless steel pipe(STS). The results of the studies were summarized as follows; By measuring the thermal characteristics of the XL and STS, it was examined that the average temperature differences of the inlet and outlet were $8.5^{\circ}C$ and $13.3^{\circ}C$, the average flowrates were 15.3 L/min and 5.6 L/min, and the average radiation powers were 9.1 kW and 4.1 kW, respectively. As results of the regression analysis of underground temperatures, when average soil temperature was$35^{\circ}C$, an average water temperature was $80^{\circ}C$, and XL was used, it was estimated that the possible heat transfer distance, the required time for heat transfer and heat flux to reach the underground temperature of $60^{\circ}C$ were 300 mm, 230 hours, and $7.57kW/m^2$, respectively.

• Corrosion Science and Technology
• /
• 제13권2호
• /
• pp.41-47
• /
• 2014

The isothermal corrosion tests of several types of stainless steels, Ni-based alloys, and ferritic-martensitic steels (FMS) were carried out at the temperature of 550 and $650^{\circ}C$ in SFR S-$CO_2$ environment (200 bar) for 1000 h. The weight gain was greater in the order of FMSs, stainless steels, and Ni-based alloys. For the FMSs (Fe-based with low Cr content), a thick outer Fe oxide, a middle (Fe,Cr)-rich oxide, and an inner (Cr,Fe)-rich oxide were formed. They showed significant weight gains at both 550 and $650^{\circ}C$. In the case of austenitic stainless steels (Fe-based) such as SS 316H and 316LN (18 wt.% Cr), the corrosion resistance was dependent on test temperatures except SS 310S (25 wt.% Cr). After corrosion test at $650^{\circ}C$, a large increase in weight gain was observed with the formation of outer thick Fe oxide and inner (Cr,Fe)-rich oxide. However, at $550^{\circ}C$, a thin Cr-rich oxide was mainly developed along with partially distributed small and nodular shaped Fe oxides. Meanwhile, for the Ni-based alloys (16-28 wt.% Cr), a very thin Cr-rich oxide was developed at both test temperatures. The superior corrosion resistance of high Cr or Ni-based alloys in the high temperature S-$CO_2$ environment was attributed to the formation of thin Cr-rich oxide on the surface of the materials.

• 한국주조공학회지
• /
• 제33권5호
• /
• pp.215-225
• /
• 2013

The alloys required for fossil power plants are altered from stainless steel that has been used below $600^{\circ}C$ to Ni-based alloys that can operate at $700^{\circ}C$ for Hyper Super Critical (HSC) steam turbine. The IN740 alloy (Special Metals Co. USA) is proposed for improved rupture strength and corrosion resistance at high temperature. However, previous studies with experiments and simulations on stable phases at about $700^{\circ}C$ indicated the formation of the eta phase with the wasting of a gamma prime phase, which is the most important reinforced phase in precipitation hardened Ni alloys, and this resulted in the formation of precipitation free zones to decrease the strength. On the basis of thermodynamic calculation, the new Ni-based superalloy named LESS 1 (Low Eta Sigma Superalloy) was designed in this study to improve the strengthening effect and structure stability by depressing the formation of topologically close packed phases, especially sigma and eta phases at high temperature. A thermal exposure test was carried out to determine the microstructure stability of LESS 1 in comparison with IN740 at $800^{\circ}C$ for 300 hrs. The experimental results show that a needle-shaped eta phase was formed in the grin boundary and it grew to intragrain, and a precipitation free zone was also observed in IN740, but these defects were entirely controlled in LESS 1.

• 대한소아치과학회지
• /
• 제26권2호
• /
• pp.339-349
• /
• 1999

본 연구에서는 수복에 따른 치질 내부 구조물의 열적변화를 평가하기 위하여 와동이 형성된 인공 치아모형에 아말감충전, 아말감과 스테인레스 스틸관 수복, 금인레이와 금관수복, ZOE 이장 및 아말감충전 등으로 수복한 후 온도변화를 관찰하였다. 각 실험군에 $4^{\circ}C$와 $60^{\circ}C$로 2초와 4초 동안 자극을 가한 후 치아내부의 온도분포를 2차원적으로 분석하였고, 치수 중앙부에서 외측으로 층을 형성하여 3차원적인 해석을 시행한 결과, 다음과 같은 결론을 얻었다. 1. $4^{\circ}C$의 자극이 2초간 가해진 아말감 충전 경우, 아말감 충전과 스테인레스 스틸관을 장착한 경우에서는 $1^{\circ}C$ 내외의 차이를 보였으며, 치수와 상아질 경계면에서 3초 경과시에 $29^{\circ}C$까지 급격한 온도 하강을 보였으며 9초 후에 $25^{\circ}C$에 도달하였다. 또한 금으로 수복한 경우에서는 3초 후 $25^{\circ}C$까지 하강하여 그 온도를 유지하였으며, ZOE 이장 경우에서는 최저온도가 $4^{\circ}C$ 이상 높게 나타났다. 2. $4^{\circ}C$ 자극을 4초간 가한 경우에서는 9초 후에서 2초 자극시보다 $2-3^{\circ}C$ 낮았으며, 금 수복 경우에는 5초 후에 $21^{\circ}C$의 최저온도를 보인 후 점차 회복되었다. 3. 아말감 충전 및 스테인레스 스틸관을 같이 장착한 경우에 $60^{\circ}C$, 2초간 자극에는 3초 후 $40^{\circ}C$의 온도로서 상승하였으나 9초 후에 $30^{\circ}C$로 하강 하였으며, 금 수복에서는 2초 후 $41^{\circ}C$까지 온도가 상승하였고, 9초 후 $28^{\circ}C$를 보여 $13^{\circ}C$의 차이가 있었다. ZOE 이장 경우에는 온도차이가 $5^{\circ}C$로서 안정된 양상을 보였다. 4. $60^{\circ}C$, 4초 자극에 대한 아말감 충전 및 스테인레스 스틸관을 같이 장착한 경우에서 5초 후 $42^{\circ}C$, 9초 후 $35^{\circ}C$를 보였으나 금 수복 경우에서는 3초 후 $49^{\circ}C$, 9초 후 $31^{\circ}C$의 온도변화를 나타내었다. 5. 3차원 분석에서 치수 중앙부에서 멀어질수록 온도변화가 심하였다.

• 한국안전학회지
• /
• 제21권3호
• /
• pp.73-80
• /
• 2006

Generally beam design depends on the yielding and maximum strength of each member varying with its section shape. Web plate of H-shape beam has not been substituted with glass plate, because it is known that its strength and heat properties are different and it is limited to substitute the existing steel web with glass element. Ceiling height of each room should be decreased with more than 60-80cm due to the beam. Differently from this condition, glass web beam has a good point to see through it and sunshine can be penetrate into the other size especially when it is installed as of outside wall. And also, it can be safer due to controlling room inside easier, if the strength is applicate. This study is to show some applicability after finding out the properties using the test. The test members with a size of $1,600{\times}200{\times}300{\times}9mm$ being SS41 rolled steel having THK 9mm flange while having 8,10mm and reinforced glass 12mm thickness is bonded with epoxy bond under the condition of temperature $28^{\circ}C$, humidity 50%, bonding power 24Mpa. It is show reinforced glass has 5 times of fracture stress more than the common glass but $50{\sim}150%$ difference between these 2 kinds of glass was shown. Reinforce glass did not support the original upper flange after fracture but the common glass did the upper flange after unloading. Generally reinforced glass is stronger than the common one but the common glass having a part of crack on it, compared with reinforced glass having the overall fracture could be more useful in case of needing ductility.