• 한국강구조학회 논문집
• /
• 제21권2호
• /
• pp.193-201
• /
• 2009

철골 Pre-Engineered Building System(PEBS)이 국내에서도 80년도 후반부터 상당히 일반화되었지만 변단면 PEBS는 대부분 국외에서 개발된 최적화 프로그램으로 구조설계가 수행되고 있다. 이 연구에서는 3차원 변단면 PEBS의 구조설계를 AISC2005의 허용응력설계법과 KBC 기준에 따라 주어진 여러 제약조건들을 만족하도록 수치해석법으로 최적화하는 프로그램을 개발하였다. 변단면 구조물의 최적화 설계는 구조해석과 최적 부재설계를 수행하는데, 구조물의 최소 중량화를 위해서 구조해석과 부재설계 과정을 허용응력조건과 변위조건이 만족될 때까지 반복 수행한다. 2, 3차원 변단면 구조물을 최적화 설계한 결과에 의하면 변단면 용접 H-형강으로 설계하는 것이 압연 H-형강보다 상당한 철골 절약효과가 있는 것으로 나타났다. 변단면 용접 H-형강으로 설계하는 경우 구조물의 종류에 따라 차이는 있지만 AISC2005 기준으로 설계하는 것이 AISC1989 기준보다 철골량이 줄어들었고, 부재 춤도 작게 설계되어 웨브 좌굴에 새 기준이 더 안전한 것으로 평가되었다.

• Steel and Composite Structures
• /
• 제1권1호
• /
• pp.17-32
• /
• 2001

The Rosette-joining system is a completely new press-joining method for cold-formed steel structures. One Rosette-joint has a shear capacity equal to that of approximately four screws or rivets. The Rosette thin-walled steel truss system presents a new fully integrated prefabricated alternative to light-weight roof truss structures. The trusses are built up on special industrial production lines from modified top hat sections used as top and bottom chords and channel sections used as webs which are joined together with the Rosette press-joining technique to form a completed structure easy to transport and install. A single web section is used when sufficient but can be strengthened by double-nesting two separate sections or by using two lateral profiles where greater compressive axial forces are met. An individual joint in the truss can be strengthened by introducing a hollow bolt into the joint hole. The bolt gives the connection capacity a boost of approximately 20%. A series of laboratory tests have been carried out in order to verify the Rosette truss system in practice. In addition to compression tests on individual sections of different lengths, tests have also been done on small structural assemblies and on actual full-scale trusses of a span of 10 metres. Design calculations have been performed on selected roof truss geometries based on the test results, FE-analysis and on the Eurocode 3 and U.S.(AISI) design codes.

• Steel and Composite Structures
• /
• 제29권1호
• /
• pp.23-37
• /
• 2018

In this paper, seismic provisions related to built-up special concentrically braced frames (BSCBFs) are investigated under cyclic loading using non-linear finite element analysis of a single-bay single-story frame. These braces, which contain double angle and double channel brace sections, are considered in two types of single diagonal and X-braced frames. The results of this study show that current seismic provisions such as observing the 0.4 ratio for slenderness ratio of individual elements between stitch connectors are conservative in BSCBFs, and can be increased according to the type of braces. Furthermore, such increments will lead to decreasing or remaining the current middle protected zone requirements of each BSCBFs. Failure results of BSCBFs, which are related to the plastic equivalent strain growth of members and ductility capacity of the models, show that the behaviors of double channel back-to-back diagonal braces are more desirable than those of similar face-to-face ones. Also, for double angle diagonal braces, results show that the failure of back-to-back BSCBFs occurs faster in comparison with face-to-face similar braces. In X-braced frames, cyclic and failure behaviors of built-up face-to-face models are more desirable than similar back-to-back braces in general.

• Advances in concrete construction
• /
• 제11권5호
• /
• pp.429-445
• /
• 2021

With regard to economic efficiency, composite fix beams are widely used to pass longitudinal shear forces across the interface. The current knowledge of the composite beam load-slip activity and shear capability are restricted to data from measurements of push-off. Modelling and analysis of the composite beams based on Euro-code 4 regarding to shear, bending, and deflection under differing loads were carried out using Finite Element through an efficient computer simulation and the final loading and sections capacity based on the failure modes was analysed. In bending, the section potential was increased by an improvement of the strength in both steel and concrete, but the flexural and compressive resistance growth is very weak (3.2% 3.1% and 3.0%), while the strength of the concrete has increased respectively from 25 N/mm² to 30, 35, and 40 N/mm² compared to the increment of steel strength by 27% and 21% when it was raised from 275 to 355 and 460 N/mm², respectively. It was found that the final flexural load capacity of fix beams was declined with increase in the fix beam span for both three steel strength. The shear capacity of sections was remained unchanged at constant steel strength and different length, but raised with final yield strength increment of steel sections by 29%, and 67% when it was raised from 275 N/mm² to 355 N/mm² and 460 N/mm², respectively.

• 한국강구조학회 논문집
• /
• 제26권6호
• /
• pp.499-509
• /
• 2014

본 연구에서는 해결방안으로 내부 콘크리트를 강섬유와 혼입하여 기둥자체의 연성과 인성을 증대시키는 것에 중점을 맞추고 있다. 즉, 강섬유 혼입량과 하중조건에 따른 내력 및 변형능력을 종합적으로 파악하여 강섬유 콘크리트와 용접조립각형 강관기둥의 상호작용을 구조, 내화측면에서 분석해 보고자 한다. 동일한 형상과 경계조건(하중비)에서 강섬유 혼입(0.375%)으로 내화성능은 약 1.1~1.3배 향상된 실험결과를 얻을 수 있었다. 강섬유 콘크리트의 균열 억제 특성은 열 하중에 의한 콘크리트의 변형저항 성능을 증가 시키면서 내화성능의 향상을 가져온 것으로 판단된다. 또한, 내부 리브의 열 변형에도 내부 콘크리트 단면은 건전한 상태로 남아있어 하중 분담능력이 증폭된 결과로 분석됐다.

• Steel and Composite Structures
• /
• 제19권5호
• /
• pp.1299-1319
• /
• 2015

This paper presents a detailed parametric study, conducted using finite element tools to cover a range of several geometric and material parameters, on the behaviour of thin-walled partially encased composite (PEC) columns. The PEC columns studied herein are composed of thin-walled built-up H-shaped steel sections with concrete infill cast between the flanges. Transverse links are provided between the opposing flanges to improve resistance to local buckling. The parametric study is confined to eccentrically-loaded columns subjected to major axis bending only. The parameters that were varied include the overall column slenderness ratio (L/d), load eccentricity ratio (e/d), link spacing-to-depth ratio (s/d), flange plate slenderness ratio (b/t) and concrete compressive strength ($f_{cu}$). The overall column slenderness ratio was chosen to be the primary variable with values of 5, 10 and 15. Other parameters were varied within each case of L/d ratio. The effects of the selected parameters on the behaviour of PEC columns were studied with respect to the failure mode, peak axial load, axial load versus average axial strain response, axial load versus lateral displacement response, moment versus lateral displacement behaviour and the axial load-moment interaction diagram. The results of the parametric study are presented in the paper and the influences of each of the parameters investigated are discussed.

• 한국구조물진단유지관리공학회 논문집
• /
• 제20권1호
• /
• pp.72-84
• /
• 2016

종래 브레이스시스템은 횡력저항 및 층변위제어에 효율적이며 골조물량 감소에 따른 경제성이 향상되어 일반적인 강구조 횡력저항시스템으로 적용되고 있다. 그러나 압축측에서 항복응력에 도달하기 전 가새의 좌굴이 발생하여 충분한 내력을 발휘하지 못하고, 내력열화형의 이력거동으로 불안정상태가 된다. 좌굴에 의한 내력저하 개선시스템으로 중심재를 구속하여 좌굴방지가 가능한 비좌굴가새는 심재의 항복 이후에도 안정적인 이력특성을 나타내어 종래 브레이스에 비하여 에너지흡수능력이 우수하다. 최근 10년간 미국, 일본 및 대만에서 매우 다양한 형상의 비좌굴가새가 제안되었으나, 기존의 실험연구에서는 그 형상이 매우 제한적인 경향을 보이고 있다. 본 연구에서는 조립형 Precast RC 보강재를 가지는 비좌굴가새를 제작하고 이력특성을 평가하기 위한 부재실험을 수행하였다. 또한 실험결과를 AISC(2005)의 요구조항과 비교하였다.

• 한국전산구조공학회논문집
• /
• 제27권2호
• /
• pp.79-86
• /
• 2014

본 논문에서는 범용 유한요소프로그램 ANSYS와 ABAQUS를 이용하여 냉간성형강으로 조립한 조립기둥의 전체좌굴과 뒤틀림좌굴에 대한 비선형해석을 위한 모델링 기법을 소개한다. 냉간성형강의 경우 두께가 얇아서 국부좌굴 등 비선형거동을 보이기 때문에 좌굴에 대한 해석에 매우 섬세한 모델링이 필요하다. ANSYS의 내연적정적모델링에 의한 해석은 좌굴 극한점 부근에서 수렴의 문제를 발생하였지만, ABAQUS의 외연적동적모델링의 경우에는 좌굴 및 좌굴이후의 부재 거동에 대해서 안정적인 결과를 제공하였다. 또한 수치해석 결과는 좌굴실험을 통해 얻어진 축내력에 비해 높은 내력을 보여주고 있다. 이는 실험과정에서 발생하는 편심에 의한 영향으로서 수치해석에 의한 좌굴내력에 적정한 보정치의 적용이 필요하며 본 논문에서는 기존 실험데이터와의 비교를 통해 0.88의 값을 제시한다.

• Steel and Composite Structures
• /
• 제13권3호
• /
• pp.239-258
• /
• 2012

In this paper, experimental investigations on high strength steel (HSS) stud connected steel-concrete composite (SCC) girders to understand the effect of shear connector density on their flexural behaviour is presented. SCC girder specimens were designed for three different shear capacities (100%, 85%, and 70%), by varying the number of stud connectors in the shear span. Three SCC girder specimens were tested under monotonic/quasi-static loading, while three similar girder specimens were subjected to non-reversal cyclic loading under simply supported end conditions. Details of casting the specimens, experimental set-up, and method of testing, instrumentation for the measurement of deflection, interface-slip and strain are discussed. It is found that SCC girder specimen designed for full shear capacity exhibits interface slip for loads beyond 25% of the ultimate load capacity. Specimens with lesser degree of shear connection show lower values of load at initiation of slip. Very good ductility is exhibited by all the HSS stud connected SCC girder specimens. It is observed that the ultimate moment of resistance as well as ductility gets reduced for HSS stud connected SCC girder with reduction in stud shear connector density. Efficiency factor indicating the effectiveness of high strength stud connectors in resisting interface forces is estimated to be 0.8 from the analysis. Failure mode is primarily flexure with fracturing of stud connectors and characterised by flexural cracking and crushing of concrete at top in the pure bending region. Local buckling in the top flange of steel beam was also observed at the loads near to failure, which is influenced by spacing of studs and top flange thickness of rolled steel section. One of the recommendations is that the ultimate load capacity can be limited to 1.5 times the plastic moment capacity of the section such that the post peak load reduction is kept within limits. Load-deflection behaviour for monotonic tests compared well with the envelope of load-deflection curves for cyclic tests. It is concluded from the experimental investigations that use of HSS studs will reduce their numbers for given loading, which is advantageous in case of long spans. Buckling of top flange of rolled section is observed at failure stage. Provision of lips in the top flange is suggested to avoid this buckling. This is possible in case of longer spans, where normally built-up sections are used.

• Journal of Radiation Protection and Research
• /
• 제47권2호
• /
• pp.99-106
• /
• 2022

Background: The radionuclide inventory calculation codes such as ORIGEN and FISPACT collapse neutron reaction libraries with energy spectra and generate an effective one-group cross-section. Since the nuclear cross-section data, energy group (g) structure, and other input details used by the two codes are different, there may be differences in each code's activation inventory calculation results. In this study, the calculation results of neutron-induced activation inventory using ORIGEN and FISPACT were compared and analyzed regarding radioactive waste classification and worker exposure during nuclear decommissioning. Materials and Methods: Two neutron spectra were used to obtain the comparison results: Watt fission spectrum and thermalized energy spectrum. The effective one-group cross-sections were generated for each type of energy group structure provided in ORIGEN and FISPACT. Then, the effective one-group cross-sections were analyzed by focusing on ⁵⁹Ni, ⁶³Ni, ⁹⁴Nb, ⁶⁰Co, ¹⁵²Eu, and ¹⁵⁴Eu, which are the main radionuclides of stainless steel, carbon steel, zircalloy, and concrete for decommissioning nuclear power plant (NPP). Results and Discussion: As a result of the analysis, ¹⁵⁴Eu and ⁵⁹Ni may be overestimated or underestimated depending on the code selection by up to 30%, because the cross-section library used for each code is different. When ORIGEN-44g, -49g, and -238g structures are selected, the differences of the calculation results of effective one-group cross-section according to group structure selection were less than 1% for the six nuclides applied in this study, and when FISPACT-69g, -172g, and -315g were applied, the difference was less than 1%, too. Conclusion: ORIGEN and FISPACT codes can be applied to activation calculations with their own built-in energy group structures for decommissioning NPP. Since the differences in calculation results may occur depending on the selection of codes and energy group structures, it is appropriate to properly select the energy group structure according to the accuracy required in the calculation and the characteristics of the problem.