• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.1
• /
• pp.85-91
• /
• 1998

In this paper, an influence of inlet pressure on the running characteristics of tilting pad thrust bearing is studied by a numerical analysis. The inlet pressure is obtained from the extended Bernoulli equation including the loss coefficient which is varied with the operating conditions. The running characteristic parameters such as the minimum film thickness, the film pressure and the film thickness ratios are calculated for various runner speeds with constant load in particular two pivot positions. The results are shown that the inlet pressure has a large influence on the minimum film thickness and other running characteristic parameters.

• 한국공간정보시스템학회:학술대회논문집
• /
• 2004.05a
• /
• pp.275-278
• /
• 2004

This paper focused on problems of design, construction, and maintenance caused by construction implementation processes. They were analyzed through case study of structure safety diagnosis projects. From the case study, it is expected that the introduction of Construction Management from the first stage of procurement will improve construction cost increase or burden on small design company. It strengthens coherent management from design and source contractor selection to build review of responsibility. The coherency will prevent changes in designing or infirm unreliable construction. It is desirable that expert opinions are considered when structure changes and establishment occur and that, if necessary, actions such as source selection, periodic audits, and diagnosis arc checked and fed back to maintenance.

• Korean Journal of Computational Design and Engineering
• /
• v.5 no.4
• /
• pp.301-311
• /
• 2000

For effective part modifications which is necessary in the design process frequently, variational geometric modeling with constraint management being used in a wide. Most variational geometric modeling methods, however, manage just the constraints about sketch elements used for generation of primitives. Thus, not only constraint propagation but also re-build of various modeling operations stored in the modeling history is necessary iota part geometry modifications. Especially, re-build of high-cost Boolean operations is apt to deteriorate overall modeling efficiency abruptly. Therefore, in this paper we proposed an algorithm that can handle all geometric entities of the part directly. For this purpose, we introduced eight type geometric constraints to the various geometric calculations about all geometric entities in sweepings and Boolean operations as well as the existing constraints of the sketch elements. The algorithm has a merit of rapid part geometric modifications through only constraint propagation without rebuild of modeling operations which are necessary in the existing variational geometric modeling method.

• The Journal of the Convergence on Culture Technology
• /
• v.6 no.3
• /
• pp.361-367
• /
• 2020

This paper proposes the battery-less ultra-low-power self-powered cooperating artificial neural networks device for embedded and IoT systems. This device can work without extraneous power supplying and can cooperate with other neuromorphic devices to build large-scale neural networks. This device has energy harvesting modules, so that can build a self-powered system and be used everywhere without space constraints for power supplying.

• Textile Coloration and Finishing
• /
• v.17 no.5 s.84
• /
• pp.13-19
• /
• 2005

Dyeing and fastness properties of direct spun type PET microfiber fabrics have been investigated. The dye uptake of finer microfibers commenced at lower temperatures and showed faster rate of dye uptake. The build-up and wet fastness properties of disperse dyes on finer microfbers were relatively poor since the more dye was needed to achieve a given depth of shade due to the large surface area.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1993.05a
• /
• pp.70-78
• /
• 1993

Heat pipes, applied to flat plate solar collectors, have a long and slender configuration with relatively low heat flux on the evaporator. Such a heat pipe has a tendency to build-up a liquid pool at the lower half of evaporator zone, and at this pool occurs such complicated phenomena of evaporation and fluid dynamics as superheat, sudden generation of bubble, its likely explosive growth process and flooding etc. In the present study, we tried to solve those problems by means of adjusting the two principle design parameters, liquid fill charge and wick length, using 4 heat pipes and 3 thermosyphons, with different values of parameter respectively. The corresponding results can be summarized as followings, - The thermal conductance of heat pipes was largely improved by el eliminating wick from adiabatic and condenser zone. - But on evaporator zone wick is inevitable to reduce behavior of the build -up of liquid pool , where arise diverse internal complex phenomena. - The liquid fill charge should have to be increased by 10∼20％ more than the quantity to saturate the wick.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.11 s.176
• /
• pp.202-209
• /
• 2005

In this paper, benchmark tests of Rapid Prototyping(RP) are presented to evaluate characteristics of various RP Systems and Processes, and several decision-support systems are developed to select RP Machine/Process suitable to user's requirements. Results of the RP benchmark tests are applied to the recently developed RP machines for the purpose of analyzing attributes such as dimensional accuracy, surface roughness, build cost, build time, and etc. Decision-making support systems are also developed, which contain not only new LCE (Linear Confidence Equation) algorithm but also modified PRES and MDS algorithm. Those algorithms are proved to be effective in that reasonably acceptable results are obtained on several cases of different inputs.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.10
• /
• pp.147-155
• /
• 2002

In the stereolithography process, the accuracy of product depends on laser power, scan speed, scan width, scan pattern, layer thickness, resin characteristics and so on. Therefore, appropriate process parameters are required for an accurate prototype. This paper presents a method to determine the key process parameters, i.e., laser scan speed, hatching space, and layer thickness based on scan length, scan area, and layer slope. In order to determine these parameters, three neural networks are employed to represent operator’s experience and knowledge. Optimum values on scan speed, hatching space and layer thickness are recommended to improve the surface roughness and build time on the developed SLA machine.

• Tribology and Lubricants
• /
• v.20 no.6
• /
• pp.330-336
• /
• 2004

In this paper, thermohydrodynamic characteristics of large tilting pad journal bearings which have $3\~8$ tilting pads were numerically analyzed. The turbulent lubrication equation and the energy equation were solved. The regime of operation of this bearing is laminar, turbulent and transitional. Also viscosity of working fluid was considered as function of only temperature and inlet pressure build-up was considered. Numerical results for a large tilting pad journal bearing showed pressure distribution, temperature distribution, eccentricity ratio, and friction torque. The effects of pad number on the static performances of a large tilting pad journal bearing are discussed.

• Journal of Korean Association for Spatial Structures
• /
• v.17 no.4
• /
• pp.141-148
• /
• 2017

In this study, an advanced form-finding method of tensegrity unit modules is presented to apply on renovation building. Here a fitness function of maximum natural frequency which can lead to a maximum stiffness status was used for a genetic algorithm. To apply the lightweight pin-jointed structure to the renovation project is more economical over to build new structures. In this paper, two types of tensegrity unit are presented to build expanded structures, and their force densities are shown using the proposed form-finding method. The expanded structures which may influence renovation projects are presented by using the tensegrity units.