• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.2
• /
• pp.199-208
• /
• 2012

This paper proposes a quasi Z-source DVR(Dynamic Voltage Restorer) system with a series connection of the output terminals, to compensate the voltage variations in the 6.6[kV]/60[Hz] power distribution system. The conventional DVR using one quasi Z-source AC-AC converter has the advantage which it can compensate the voltage variations without the need for the additional energy storage device such as a battery, but it is impossible to compensate for the 50[%] under voltage sags. To solve this problem, a DVR system using two quasi Z-source AC-AC converters with the series connection of the output terminals is proposed. By controlling the duty ratio D in the buck-boost mode, the proposed system can control the compensation voltage. For case verification of the proposed system, PSIM simulation is achieved. As a result, in case that the voltage sags-swells occur 10[%], 20[%], 60[%] in power distribution system, and, in case that the 50[%] under voltage sags-swells continuously occur, all case could compensate by the proposed system. Especially, the compensated voltage THD was examined under the condition of the 10[%]~50[%] voltage sags and the 20[${\Omega}$]~100[${\Omega}$] load changes. The compensated voltage THD was worse for the higher load resistances and more severe voltage sags. Finally, In case of the voltage swells compensation, the compensation factor has approached nearly 1 regardless of the load resistance changes, while the compensation factor of voltage sags was related to the load variations.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.37 no.1
• /
• pp.86-92
• /
• 1992

Green buckwheat seedlings have been used as a pollution free vegetable and medicinal crop for a long time. Some of the reasons are the rapid growth rate, the high protein and rutincontent, and a more favorable ratio of leaf to stem than mature plants. Off-crop season cultivation techniques were developed for growing the young and green buckwheat vegetable of higher quality and yield, and for its increased value-added income. The effects of planting season, seeding rate, seed bed soil fertility and type, and seedling growth period on yield and rutin content were determined for vegetable and medicinal use. The young vegetable yields. in the off season culture ranged from 2.62t/ha to 22.7t /ha. The highest vegetable yield was 22.7t /ha for 25 days old seedlings grown in the polyethylene film tunnel from March 30 to April 25, 1991 where seedling rate was 360kg /ha. Buckwheat vegetable quality and income were dependent upon planting season, seeding rate, growing duration and temperature, and facilities of raising seedlings. Protein content of buck-wheat seedlings was from 21.5% to 17.2%. Rutin content of the vegetable was 53.9～31.7mg /100g for the whole plant in average. The protein and rutin content was significantly varied due to the different environmental conditions including fertility and type of seed bed soil, growing duration, temperature of the green house, and polyethylene film house and tunnel.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.10
• /
• pp.231-238
• /
• 2013

This paper describes a DC-DC converter IC for Flat Panel Displays. In case of operate LCD devices various type of DC supply voltage is needed. This device can convert DC voltage from 6~14[V] single supply to -5[V], 15[V], 23[V], and 3.3[V] DC supplies. In order to meet current and voltage specification considered different type of DC-DC converter circuits. In this work a negative charge pump DC-DC converter(-5V), a positive charge pump DC-DC converter(15V), a switching Type Boost DC-DC converter(23V) and a buck DC-DC converter(3.3V). And a oscillator, a thermal shut down circuit, level shift circuits, a bandgap reference circuits are designed. This device has been designed in a 0.35[${\mu}m$] triple-well, double poly, double metal 30[V] CMOS process. The designed circuit is simulated and this one chip product could be applicable for flat panel displays.

• Journal of Advanced Marine Engineering and Technology
• /
• v.41 no.1
• /
• pp.76-82
• /
• 2017

Since the introduction of electronically controlled engines and electric propulsion ships, the need for an uninterruptible power supply for emergency power supply devices that use batteries has gained importance. The bidirectional converter in such emergency power supply devices is a crucial component. This paper proposes, a topology for an improved DC-DC bidirectional converter that is characterized by a high voltage conversion ratio and low voltage stress of switches. To confirm the performance of the converter, a computer simulation was executed with PSIM software. The conversion ratio of the proposed converter was found to be four times higher than the conventional boost converter in step-up mode and one-fourth that of the conventional buck converter in step-down mode, and the voltage stress of the switches was one-fourth of the high-side voltage. Moreover, the proposed converter was confirmed to be able to distribute equal currents between two interleaved modules without using any extra current-sharing control method because of the charge balance of its blocking capacitors.

• Journal of Korean Institute of Industrial Engineers
• /
• v.28 no.2
• /
• pp.216-222
• /
• 2002

The ergonomic human model can be considered as a tool for the evaluation of ergonomic factors in vehicle design process. The proper anthropometric data on driver's postures are needed in order to apply a human model to vehicle design. Although studies on driver's posture have been carried out for the last few decades, there are still some problems for the posture data to be applied directly to the human model due to the lack of fitness because such studies were not carried out under the conditions for the human model application. In the traditional researches, the joint angles were evaluated by the categorized data, which are not appropriate for the human model application because it is so extensive that it can not explain the posture evaluation data in detail. And the human models require whole-body posture evaluation data rather than joint evaluation data. In this study a postural evaluation function was developed not by category data but by the concept of the loss function in quality engineering. The loss was defined as the discomfort in driver's posture and measured by the magnitude estimation technique in the experiment using a seating buck. Four loss functions for the each joint - knee, hip, shoulder, and elbow were developed and a whole-body postural evaluation function was constructed by the regression analysis using these loss functions as independent factors. The developed postural evaluation function shows a good prediction power for the driver's posture discomfort in validation test. It is expected that the driver's postural evaluation function based on the loss function can be used in the human model application to the vehicle design process.

• IE interfaces
• /
• v.23 no.2
• /
• pp.100-107
• /
• 2010

For proper ergonomic evaluation using a digital human model simulation (DHMS) system such as $RAMSIS^{(R)}$, the postures of humanoids for designated tasks need to be predicted accurately. The present study (1) evaluated the accuracy of driving postures of humanoids predicted by RAMSIS, (2) proposed a method to improve its accuracy, and (3) examined the effectiveness of the proposed method. The driving postures of 12 participants in a seating buck were measured by a motion capture system and compared with their corresponding postures predicted by RAMSIS. Significant discrepancies ($8.7^{\circ}$ to $74.9^{\circ}$) between predicted and measured postures were observed for different body parts and driving tasks. Two methods (constraints addition and user-defined posture) were proposed and their effects on posture estimation accuracy were examined. Of the two proposed methods, the user-defined posture method was found preferred, reducing posture estimation errors by 11.5% to 84.9%. Both the posture prediction accuracy assessment protocol and user-defined posture method would be of use for practitioners to improve the accuracy of predicted postures of humanoids in virtual environments.

• Archives of Plastic Surgery
• /
• v.35 no.5
• /
• pp.619-621
• /
• 2008

Purpose: By virtue of good nourishment, obese boys are increasing in Korea, which may result in prevalence of cryptopenis. As milieu of economy, culture, and society changes, increased attention to the external genitalia in children should encourage surgeon to do assertive treatment for cryptopenis. But various operative methods have been devised yet to need sophistication and revision. The author performed suprapubic lipectomy and operation according to the modification of the Johnston's principle. Methods: The patient was 5 years old, 32 kg, and 122 cm. He had no pain or tenderness. The operation was done under general anesthesia. It was done with excision of suprapubic fat, cutting of retracted dartos fascia instead of removing the fascia around penile base, and anchoring of dermis and the cutting margin of the fascia to the underlying fascia such as Buck's fascia, tunica albuginea and rectus fascia at penile base. And then circumcision was performed. Results: Postoperative complication was not observed. The clinical result of the operation was satisfactory to both surgeon and parents of the patient. Conclusion: Suprapubic lipectomy and anchoring of dermis and retracted cutting dartos fascia margin to the underlying fascia in all directions at the penile base through a single suprapubic incision provide this patient with complacency.

• Journal of Biosystems Engineering
• /
• v.43 no.2
• /
• pp.94-102
• /
• 2018

Purpose: In this study, a maintenance free super-capacitor battery charging system based on the photovoltaic module, to be used in agricultural electric carriers, was developed and its charging characteristics were studied in detail. Methods: At first, the electric carrier system configuration is introduced and the electric control components are presented. The super-capacitor batteries and photovoltaic module used in the experiment are specified. Next, the developed charging system consisting of a constant current / constant voltage Buck converter as the charging device and a super-capacitor cell as a balancing device are initiated. The proposed circuit design, a developed PCB layout of each device and a proportional control to check the current and voltage during the charging process are outlined. An experiment was carried out using a developed prototype to clarify the effectiveness of the proposed system. A power analyzer was used to measure the current and voltage during charging to evaluate the efficiency of the energy storage device. Finally, the conclusions of this research are presented. Results: The experimental results show that the proposed system successfully controls the charging current and balances the battery voltage. The maximum voltage of the super-capacitor battery obtained by using the proposed battery charger is 16.2 V, and the maximum charging current is 20 A. It was found that the charging time was less than an hour through the duty ratio of 95% or more. Conclusions: The developed battery charging system was successfully implemented on the agricultural electric carriers.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.1
• /
• pp.82-91
• /
• 2017

This paper is a study on the bi-directional DC-DC converter, one of the key elements of 48V-12V dual systems in mild hybrid electric vehicles. Mild hybrid electric vehicles require a bi-directional DC-DC converter that can efficiently transmit power in two directions between a 48V battery and a 12V battery. To develop a bi-directional DC-DC converter with better price competitiveness, upgraded fuel economy, excellent performance and smaller size, this study designed, produced and presented a circuit that improved on the existing one. In the proposed 8-phase bi-directional DC-DC converter, the size of the passive element was reduced through the 8-phase interleaved topology, whereas downscaling had previously posed a difficulty. This study also designed and produced a 2.5kW class prototype. Based on the proposed 8-phase interleaved topology, a size of 227.5 (W) * 172 (L) * 64.35 (H) was achieved. In the boost mode operation and buck operation modes, the maximum efficiency was recorded at 94.04 % and 95.78 %, respectively.

• Journal of Embryo Transfer
• /
• v.15 no.3
• /
• pp.287-293
• /
• 2000

This study was undertaken to access the effects of collection method, room temperature at oocyte recovery and culture media on the oocyte quality, fertilization and cleavage rates of in vitro matured and fertilized oocytes of Korean native goats. Ovaries obtained from a slaughterhouse were transported to the laboratory and were divided into 2 groups. One group of ovaries was maintained at 30 to 35$^{\circ}C$ of the room temperature and another group was remained at 20 to $25^{\circ}C$ during oocyte recovery. The oocytes were recovered by follicle aspiration, slicing and aspiration+slicing methods from 3 groups of follicles according to size; <2 mm, 2 to 6 mm and >6 mm. The matured oocytes were inseminated with buck epididymal spermatozoa at a concentration of 3~3.5$\times$10$^{6}$ m1 and fertilization was identified when 2 pronuclei were present in the cytoplasm. Although the recovery rate per ovary obtained by the combination of follicle aspiration + slicing(19.6$\pm$2.2) method was higher than aspiration(11.7$\pm$1.1) and slicing(14.8$\pm$1.8) collection, optimal recovery according to oocyte grades resulted form ovarian slicing compared to aspiration or combined methods(P<0.05). However, no significant differences were found in the mean number(2.5$\pm$1.8; 3.3$\pm$3.3; 2.9$\pm$2.4) and the proportion of favorable oocytes(Grades I, II and III) recovered(31.6%, 36.0%, 36.4%,) according to follicle size(<2 mm; 2 to 6 mm; >6 mm). Fertilization rate was 60.0%, 67.7%, 70.6% and 56.4% and the proportion of embryos/zygotes was 11.1%, 7.1%, 5.0% and 2.8% in 20~$25^{\circ}C$/BO, 30~35$^{\circ}C$/BO, 20~$25^{\circ}C$/TALP and 30~35$^{\circ}C$ /groups, respectively.