• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3015-3020
• /
• 2007

An experimental study of the dynamic characteristics of the free rising oblate spherical bubble is investigated. As noted by Saffman, the characteristics of the spiral motion are defined with parameters of the spiral frequency, spiral radius, and rising velocity. High speed camera recorded every detail information of free rising bubble. The spiral number, the bubble rise velocity, and the angular velocities were measured for the bubble size between 1.0mm to 20.0mm in diameter. In order to make clear trajectory, we employed the Fast Fourier Transformation for the normal digital camera data to synchronize with the high speed camera data. It was found that the spiral number suggested here was monotonically decreased as the bubble size increases. The present observation, however tells us that previous Saffman's formulation shows a good agreement with the trend, but over estimated spiral number. Therefore, it is recommended that Saffman's theoretical study is needed to be improved.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1201-1206
• /
• 2004

Sonoluminescence (SL) characteristics such as pulse shape, radiance and spectrum radiance from submicron bubbles were investigated. In this study, a set of analytical solutions of the Navier-Stokes equations for the gas inside bubble and equations obtained from mass, momentum and energy equations for the liquid layer adjacent the bubble wall were used to estimate the gas temperature and pressure at the collapse point, which are crucial parameters to determine the SL characteristics. Heat transfer inside the gas bubble as well as at the liquid boundary layer, which was not considered in the most of previous studies on the sonoluminescence was taken it into account in the calculation of the temperature distribution inside the bubble. It was found that bremsstrahlung is a very possible mechanism of the light emission from either micron or submicron bubbles. It was also found that the peak temperature exceeding $10^{6}$ K in the submicron bubble driven at 1 MHz and 4 atm may be due to the rapid change of the bubble wall acceleration near the collapse point rather than shock formation.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.2 s.107
• /
• pp.190-197
• /
• 2006

It is well known that the acoustic characteristics of the sea are significantly affected by bubbles which have their own inherent characteristics at the undersea. In this study, the shape and acoustic characteristics of air bubbles generated by an underwater nozzle are calculated numerically, and are measured with a high speed camera and a hydrophone at various air flow rates in the experimental apparatus. As a result of analysis, the shape calculated numerically well matched with measured values at low flow rates, but in case of relatively higher flow rates. the use of correction coefficient is needed for more accurate estimation of the bubble shape. And also the rising velocity of a single bubble is constant regardless of both the bubble size and the flow rate. and the acoustic signal generated when the bubble is produced by an underwater nozzle has the same characteristic of natural frequency of the bubble pulsation, and is agreed with Minnaert's equation if the correction coefficient is considered in accordance with the flow rate.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.6 no.1
• /
• pp.69-76
• /
• 2000

Bubble boom may be a good alternative for the prevention of oil spill pollution due to its easy deployment and clean post-process tasks. The present work is focused on the experimental investigation of air bubble movement for the bubble boom by visualization and quantitative PIV measurements. Bubble plume was generated by adjusting the pressure of pressure vessel ranging 6.7 kpa to 14.7 kpa. The results showed at lower inlet velocity and higher supply air flow rate that bubble boom maintained its containing capability reasonably well up to the maximum containing limit.

• Journal of Korean Society of Water and Wastewater
• /
• v.16 no.6
• /
• pp.663-669
• /
• 2002

Electro-flotation (EF) has shown advantages, such as a high removal efficiency and easy control of bubble generation, over dissolved air flotation. However, the fundamental characteristics of the process have not been investigated in detail. According to recent modeling results from trajectory analysis, the size of the bubble is one of the most important factors that affect the efficiency of collision between bubble and particle. In this paper, the size characteristics of bubbles generated from EF under various conditions are measured using a new method for bubble size measurement, the Particle Counter Method (PCM). The size of the generated bubbles was found to be constant with respect to applied voltage but to vary with the electrode materials. These results and their implications are discussed.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.1
• /
• pp.55-61
• /
• 2011

This paper presents bubble wake measurement results generated by the planing hull. The bubble was generated by SNAME TMB model(No. 4876) with hard chine at the CWC(Circulating Water Channel). ABS(Acoustic Bubble Spectrometer) was used to measure bubble wake measurement. The manufactured model is one meter in length and uniform velocity to generate the bubble at CWC is 3m/s, relatively higher speed than conventional hull form. Measurements were performed successfully and measured results show well the general characteristics of bubble wake generated by planing hull. Furthermore, experimental equations are proposed for the practical use.

• Journal of the Korean Society of Visualization
• /
• v.20 no.2
• /
• pp.55-62
• /
• 2022

We experimentally investigate a rising toroidal bubble impacting a free surface. The toroidal bubble is created by releasing pulsed air. By adjusting the volume and circulation of the toroidal bubble, the characteristics of interactions between the toroidal bubble and the free surface are identified. Because of the impact by the toroidal bubble, the free surface is convexly deformed upwards above the center point of the toroidal bubble, while the edge of the deformed free surface is pulled down. When the circulation of the bubble becomes stronger, the surface which was pulled down breaks eventually, and air above the free surface is entrained into water, forming an unstable toroidal bubble. The deformations at the center and edge of the free surface are in a linear relationship with the Froude number and the Weber number, respectively.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.25 no.5
• /
• pp.246-254
• /
• 2013

Some characteristics of nitrogen-water slug flow were optically measured, in vertical acrylic tubes of 2, 5 and 8 mm diameter. Bubble velocity, bubble and unit cell lengths were measured, by analyzing the light intensity signals from two sets of dot laser-infrared sensor modules mounted along the transparent tubes. Optical images of the bubbles were also taken and analyzed, to measure bubble shapes and liquid film thickness. It was found that the measured bubble velocities were in good agreement with the empirical models in the literature, except for those measured under high superficial velocity condition in the 2 mm tube. Bubble length was found to be the longest in the 2 mm tube, being 4 to 5 times those of the other tubes. Liquid film was found to have developed early in the 2 mm tube, which made the blunt shape of the bubble head. Liquid film thickness in the 8 mm tube was measured at almost twice those of the other tubes.

• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.5
• /
• pp.617-623
• /
• 2003

In the present study, the characteristics of upward bubble flow were experimentally investigated in a liquid bath. The velocity of upward bubble flow was calculated for two different experimental conditions：1) bubble flow without kinetic energy 2) bubble flow with kinetic energy. Bubble flow without kinetic energy starts to undergo the effect of buoyancy l0cm away from the nozzle. Whereas. kinetic energy is dominant before 30 cm away from the nozzle in bubble flow but after this point kinetic energy and inertial force are applied on bubble flow at the same time In addition, as the flow rate increases the maximum velocity point moves to the nozzle. The velocity Profiles near free surface is extremely irregular due to surface flow. Gas volume fraction is high near the nozzle due to gas concentration. but decreases with the increasement of axial position. Gas volume fraction does not vary after the axial position, z=60 in spite of the increasement of flow.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.2105-2108
• /
• 2003

The characteristics of upward bubble flow were experimentally investigated in a liquid bath. In the present study, a thermal-infrared camera and high speed CCO camera were used to measure their temperature and local rising velocity, respectively. Heat transfer from bubble surface to water is largely completed within z=10mm from the nozzle, and then the temperature of bubble surface reaches that of water rapidly. The rising velocity of bubble was calculated for two different experimental conditions: 1) bubble flow without kinetic energy 2) with kinetic energy. Bubble flow without kinetic energy starts to undergo the effect of inertia force 10cm away from the nozzle. Whereas, kinetic energy is dominant before 30 cm away from the nozzle in bubble flow, but after this point, kinetic energy and inertial force are applied on bubble flow at the same time.