• Journal of the Korean Wood Science and Technology
• /
• v.27 no.3
• /
• pp.17-22
• /
• 1999

The effect of microwave irradiation on wood bending was investigated in this study. The specimens irradiated with microwave were bent around a form by using pedestal-steel and clamps. The specimens, korea red pine (Pinus densiflora), for this test were water-soaked for 78 hours. Saturated specimens were boiled in water for an hour. The size of specimens was 350mm(L) by 20mm(R) by 10mm(T). These specimens were heated by microwave of 2,450MHz. The most suitable time for microwave irradiation seems to range from 60 to 90 seconds. Wood moisture content decreased remarkably with the increase of irradiation time. When a softened wood piece is bent, its convex side was stretched while the concave side was compressed. It can be compressed considerably, but stretched very little. Therefore the failure will be governed by the tensile breaking strain and occur mainly on the convex face. So we obtained results from three different bending process methods as follows : 1) When bending with a pedestal-steel, convex face had not tensile breakings, but concave face had compression fails. 2) When bending with a clamp, bending time increased more than pedestal-steel and occurred tensile breaking. 3) Bending with a pedestal-steel and a clamp was found to be the most excellent operation method in this study.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.10 no.11
• /
• pp.5476-5496
• /
• 2016

Energy efficiency of resource-constrained wireless sensor networks is critical in applications such as real-time monitoring/surveillance. To improve the energy efficiency and reduce the energy consumption, the time series data can be compressed before transmission. However, most of the compression algorithms for time series data were developed only for single variate scenarios, while in practice there are often multiple sensor nodes in one application and the collected data is actually multivariate time series. In this paper, we propose to compress the time series data by the Lasso (least absolute shrinkage and selection operator) approximation. We show that, our approach can be naturally extended for compressing the multivariate time series data. Our extension is novel since it constructs an optimal projection of the original multivariates where the best energy efficiency can be realized. The two algorithms are named by ULasso (Univariate Lasso) and MLasso (Multivariate Lasso), for which we also provide practical guidance for parameter selection. Finally, empirically evaluation is implemented with several publicly available real-world data sets from different application domains. We quantify the algorithm performance by measuring the approximation error, compression ratio, and computation complexity. The results show that ULasso and MLasso are superior to or at least equivalent to compression performance of LTC and PLAMlis. Particularly, MLasso can significantly reduce the smooth multivariate time series data, without breaking the major trends and important changes of the sensor network system.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.11 no.1
• /
• pp.31-37
• /
• 1991

Acoustic emission(AE) signals detected during metal cutting were applied as the experimental test to sensing tool wear and chipping on the NC vertical milling machine. The in-process detection of cutting tool wear including chipping, cracking and fracture has been investigated by means of AE in spite of vibration or noise through intermittent metal cutting, then the following results were obtained 1) When the tool wear is increased suddenly, or the amplitude of AE signals changes largely, it indicates chipping or breaking of the insert tip. 2) It was confirmed that AE signal is highly sensitive to the cutting speed and tool wear. 3) At the early period of cutting, the wear were large and RMS value increased highly by the influence of minute chipping and cracking, etc. Therefore, the above situations should be considered for the time when the tool would be changed.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2002.11a
• /
• pp.37-41
• /
• 2002

Lap splice is used in building construction up to recently. As buildings become higher and larger, the use of high tensile bar is increasing due to increasing in the use of high compression concrete. However the using of high tensile bar in lap splice causes eccentricity and difficulty in placing of concrete inside the form, therefore not allowing enough intervening material. Various mechanical connection are being developed but the coupler of today needs either a secondary intervening material or secondary processing that consumes much time. Therefore a coupler, needing neither a secondary intervening material nor secondary processing, was made in this study which lead to following results. (1) Breaking occurred in all experimented rebar. (2) Acquirement of tension exceeding the standard requirement. (3) Acquirement of elongation percentage within the standard requirement.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.2
• /
• pp.202-207
• /
• 2012

Multi-stage deploying beams are useful for transporting parts or products handling in production lines. However, such multi-stage beams are often exposed to unwanted vibration due to the presence of their flexibility and time-varying properties. This paper is concerned with dynamic modeling and analysis of 2-stage axially deploying beams under gravity by using the finite element method. A variable domain finite element method is employed to develop the dynamic model. A rigorous method to account for engagement of two-stage beams during the deploying procedure is introduced by breaking the entire domain into three variable domains. Several deploying strategies are tested to analyze the residual vibrations. Several examples are illustrated to investigate the self-induced damping and the effects of deploying strategy on the vibrations.

• Journal of Dairy Science and Biotechnology
• /
• v.14 no.1
• /
• pp.33-42
• /
• 1996

Food-borne illnesses remain a world-wide public heath problem, Codex food standards, codes of practice and other guidelines protect consumers from unsafe food. Codex Alimentarius helps to reach this goal by combining consumer protection with food production and trade. Codex provides reassurance to anyone anywhere that foods produced according to its codes of hygienic practice and complying with its standards are safe and nutritious and offer adequate health protection. The Codex Alimentarius Commission is a science-based, international organization. Its standards, guidelines and recommendations are recognized world-wide for their vital role in protecting the consumer and facilitation international trade. At the same time they allow food producers, processors and traders access to markets by breaking down artificial nontariff barriers to trade.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.3
• /
• pp.64-74
• /
• 2007

The continuous chip in turning operation deteriorates precision of workpiece and causes a hazardous condition to operator. Thus the chip form control becomes a very important task for reliable machining process. So, grooved chip breaker is widely used to obtain reliable discontinuous chip. However, developing new cutting insert having chip breaker takes long time and needs lots of research expense due to a couple of processes such as forming, sintering, grinding and coating of product and many different evaluation tests. In this paper, performance of commercial chip breaker is evaluated with neural network which is learned with a back propagation algorithm. For the evaluation, several important elements(depth of cut, land, breadth, radius) which directly influence the chip formation were chosen among commercial chip breakers and were used as input values of neural network. With the results of these input values, the performance evaluation method was developed and applied that method to the commercial tools.

• Journal of the Korean Applied Science and Technology
• /
• v.22 no.3
• /
• pp.234-240
• /
• 2005

In this study, we have prepared three kinds of enteric tablet coating formulations for prevention the crack incidence and enhanced process improvement of enteric tablet using aqueous system. we determined the mechanical strength of three formulatons on the enteric film-coating process. The compared experiment of one-layer and two-layer (A), (B) coating treated having placebo tablets without breakline and logo. In result, the breaking force time of two-layer (B) film strength was found to increase 0.8min than two-layer (A). We confirmed the half reduction of working hour and the simplification in the one-layer coating process, and the coating troubles was solved as setting up a dehumidifier in inlet of coater. In result, we recovered that optimum running capacity(g/kg) of dehumidifier is 10g/kg and below.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.5
• /
• pp.626-634
• /
• 2018

These days, widespread use of sensitive loads and distributed generators makes static transfer switch (STS) an essential component in power circuits to achieve a good power quality for AC Grids. In case of a short-circuit fault, previous STS cannot break the fault current. However, the proposed STS has the capability of breaking it quickly as a circuit breaker. Also if there are power quality problems such as Sag/Swell, the proposed STS can quickly transfers the load to the good quality source. Furthermore it is proved that the transfer time of the proposed STS is within one half of period of 3-phase source frequency regardless of the type of load. It is anticipated that the proposed STS may be utilized to realize many stable and reliable AC grid systems.

• Current Research on Agriculture and Life Sciences
• /
• v.27
• /
• pp.29-33
• /
• 2009

Liquefied-wood polymer composite was prepared and mechanical properties was evaluated to develop potential utility of liquefied wood. The liquefied wood was made from waste wood and chemical modified with acetic anhydride and maleic anhydride (MA), phtalic anhydride (PA). The composite sheet was prepared from modified liquefied-wood and polymer(PE). The mechanical, chemical and microscopical properties composite sheet were investigated. The results were summarized as follows, 1. The tensile strength was increased and breaking elongation of composite sheet was decreased with the time of acetylation and the dosage of MA. 2. The Young's modulus of composite sheet was gradually decreased with the dosage of PA. 3. The peak intensity of 1737cm-1 in FT-IR spectra of chemical modified liquefied woods was increased. 4. The dispersity of liquefied woods with PE was improved with chemical modification.