• Steel and Composite Structures
• /
• v.26 no.6
• /
• pp.771-791
• /
• 2018

This paper deals with the low velocity impact response and dynamic stresses of composite sandwich truncated conical shells (STCS) with compressible or incompressible core. Impacts are assumed to occur normally over the top face-sheet and the interaction between the impactor and the structure is simulated using a new equivalent three-degree-of-freedom (TDOF) spring-mass-damper (SMD) model. The displacement fields of core and face sheets are considered by higher order and first order shear deformation theory (FSDT), respectively. Considering continuity boundary conditions between the layers, the motion equations are derived based on Hamilton's principal incorporating the curvature, in-plane stress of the core and the structural damping effects based on Kelvin-Voigt model. In order to obtain the contact force, the displacement histories and the dynamic stresses, the differential quadrature method (DQM) is used. The effects of different parameters such as number of the layers of the face sheets, boundary conditions, semi vertex angle of the cone, impact velocity of impactor, trapezoidal shape and in-plane stresses of the core are examined on the low velocity impact response of STCS. Comparison of the present results with those reported by other researchers, confirms the accuracy of the present method. Numerical results show that increasing the impact velocity of the impactor yields to increases in the maximum contact force and deflection, while the contact duration is decreased. In addition, the normal stresses induced in top layer are higher than bottom layer since the top layer is subjected to impact load. Furthermore, with considering structural damping, the contact force and dynamic deflection decrees.

• Journal of the Korean Vacuum Society
• /
• v.7 no.2
• /
• pp.118-126
• /
• 1998

A study to improve filling of semiconductor contact holes by enhancement of the directionality of the source beams has been undertaken. The collimation of source beams was improved by the ionized cluster beam deposition technique with modification of the cell geometry. The collimation tested with neutral beam was excellent. But, the Cu flims were grown in a columnar mode due to the lack of surface mobilit of the impinged clusters. A shadow effect also caused cleavage and consequent discontinuity at the steos as films grow. By applying acceleration voltage, the columnar growth in a contact hole of 0.5 $\mu$m diameter and 1 $\mu$m height disappeared and considerable coverage at the side wall of the contacts as well as perfect bottom coverage were observed. These are all due to the assistants of the accelerated ionized clusters with high kinetic energy. Thus we demonstrated that the ICB deposition technique can be used to completely fill sub-half-micron contact holes with high aspect ratio.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.905-910
• /
• 2003

One of the methods that are used to compare and verify the supporting performance of the spacer grids developed is the vibration characteristic test. A modal test in this paper is performed for a dummy rod 3,847mm tall supported by eight New Doublet (ND) spacer grids. For the vibration test in air, nine accelerometers, one displacement sensor and one shaker are used for acquiring signals, and an I-DEAS TDAS software is employed for analyzing the signals. Also, a finite element (FE) analysis is performed by a beam-spring simple model and a contact model simulating the contact phenomenon between the rod and the fm spring. And then, the result of the FE analysis is compared with that of the modal test. The natural frequencies as well as the mode shapes calculated by the proposed contact models have a greater similarity to the test results than those by the previous beam-spring model. In addition, for grasping whether or not the modal parameters are influenced by where shaking spot is, two kinds of tests are performed; one is for the shaker attached at the fourth span (center), the other is for the shaker at the fifth span that is one span nearer to the bottom of the rod. The latter shows higher MAC than the former. Finally, the vibration displacements are measured in the range of 0.112-0.214mm for the excitation force of 0.25-0.75 N.

• Transactions on Electrical and Electronic Materials
• /
• v.8 no.1
• /
• pp.36-40
• /
• 2007

Inorganic layers, such as SiOxNy and SiOx deposited using plasma sublimation method, were tested as passivation layer for organic thin-film-transistors (OTFTs). OTFTs with bottom-gate and bottom-contact structure were fabricated using pentacene as organic semiconductor and an organic gate insulator. SiOxNy layer gave little change in characteristics of OTFTs, but SiOx layer degraded the performance of OTFTs severely. Inferior barrier properties related to its lower film density, higher water vapor transmission rate (WVTR) and damage due to process environment of oxygen of SiOx film could explain these results. Polyurea and polyvinyl acetates (PVA) were tested as organic passivation layers also. PVA showed good properties as a buffer layer to reduce the damage come from the vacuum deposition process of upper passivation layers. From these results, a multilayer structure with upper SiOxNy film and lower PVA film is expected to be a superior passivation layer for OTFTs.

• Journal of Ocean Engineering and Technology
• /
• v.23 no.1
• /
• pp.67-73
• /
• 2009

This study presents the results of a slamming experiment using a pneumatic cylinder. The employment of the pneumatic cylinder showed a relatively good repeatability when the results were compared with those of other slamming devices. The experiment was done for various incident angles. An air pocket was believed to cause a reduction in the magnitude of the impact pressure with an incident angle of $0^{\circ}$ for the water entry. A high speed camera was used in an attempt to locate the time of the contact between the bottom of the specimen and the free surface. It seemed that the maximum pressure occurred before the water contacted the bottom of the specimen.

• KIEAE Journal
• /
• v.10 no.1
• /
• pp.25-31
• /
• 2010

An experimental investigation of composite beams composed of wide flange steel and precast concrete is presented. The bottom flange of the steel section is encased in precast concrete. The composite beams tested in this study were designed to reduce the depth of the slab and beam. The slabs are constructed on top of the edges of the Structural Composite Hybrid System, instead of on top of the steel flange, decreasing the depth of the beams. When concrete is cast on the metal deck plate located on the edges of the precast concrete, the weight of the concrete slabs and other construction loads must be supported by the contacts between the steel and the precast concrete. This interface must not exhibit bearing failures, shear failures, and failures caused by torque due to the loading of the precast concrete. When the contact area between the concrete and the bottom flange of the steel beam is small, these failures of the concrete are likely and must be prevented. The premature failure of precast concrete must not also be present when the weight of the concrete slabs and other construction loads is loaded. This paper presents a load carrying capacity of Structural Composite Hybrid System in order to observe the failure mode. The symmetrically distributed loading that caused the failure of the composite beam was found. The paper also provides design recommendations of such type of composite structure.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.63-63
• /
• 2000

Deep submicron device contact hole에서의 bottom step coverage의 향상 및 SALICIDE공정의 필요성에 의해 collimated sputtering 및 ionized sputtering 등의 다양한 증착방법이 연구되어왔다. 반도체소자의 고집적화 및 미세화에 따라서 기존의 증착방법보다 더 높은 throughput을 가진 새로운 증착방법의 필요성이 대두되고 있다. Collimated sputtering방식으로 증착한 박막의 경우에는 증착속도가 느리고 collimator의 사용기간에 따른 공정조건의 변화가 단점으로 작용하였고 새로이 ionzied sputtering방식이 개발되었다. ionzied sputtering방식은 증착되는 금속 입자를 이온화시키고 기판에 바이어스를 걸어서 증착되는 입자의 방향성 및 증착속도의 향상을 얻을 수 있었다. 하지만 고집적도가 더욱 증가함에 따라서 더 높은 박막의 증착속도, bottom step coverage의 향상, 방향성의 향상과 더불어 증착되는 입자의 이온화 율의 증가 및 기존의 증착방식에 의한 박막보다 향상된 물성을 가진 박막증착의 필요성에 의해 hollow cathode magnetron sputtering방식이 연구되었다. HCM방식으로 titanium 박막을 증착하여 collimated sputtering 및 ionize sputtering 방식으로 증착한 titanium 박막과 물성을 비교해서 증착방식에 따른 박막물성의 차이를 연구하였다. 증착전에 기판온도는 30$0^{\circ}C$를 유지하였고 base pressure는 5.0$\times$10-9torr, working pressure는 5.7m torr로 유지하였다. power는 30kW를 가하여 50nm두께의 titanium박막을 증착하였다. 증착된 박막의 미세구조는 TEM 및 XRD로 분석하였다. HCM방식으로 증착한 titanium박막은 5nm두께의 비정질 층이 관찰되었고 ionized sputtering방식으로 증착한 titatnium박막에서 나타나는 것으로 보고된 silicon (002)와 titanium (0002) eledtron diffraction spot사이의 (10-10)spot은 관찰되지 않았다. 박막은 크고 작은 grain의 연속적 분포를 가졌고 HCM방식으로 증착한 titanium박막의 in-plane grain size가 다른 증착방식으로 증착한 박막에 비해 크게 관찰됨을 Plan-view TEM 분석을 통해서 확인되었다.

• International conference on construction engineering and project management
• /
• 2017.10a
• /
• pp.52-61
• /
• 2017

Considering its significant impact on the cost and schedule of construction projects, formwork as one part of temporary facility categories in construction should be arranged precisely. Current practice in the formwork planning is often conducted manually and repetitively, causing low efficiency and time waste. This study proposes an automated framework to generate more accurate and detailed formwork plans by utilizing information from building information modeling (BIM) considering the adequate geometric and semantic information provided by the BIM model. The dimensions and quantities information of elements in a building can be extracted automatically. Then, a rule is prepared for calculating the required forms erected around elements based on the contact areas. Finally, an algorithm of integrating first fit decreasing (FFD) with coordinated bottom left (CBL) is applied to automatically generate the formwork plan. The BIM-based automated planning framework is demonstrated by an illustrative example. The results show that the proposed framework can generate the formwork plan accurately and automatically, and significantly improve the efficiency in the formwork plan and reuse.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.2
• /
• pp.89-96
• /
• 2020

In this study, we developed a finite element model for the built-in bottom-freezer type refrigerator and then used the structural analysis method to analyze and evaluate the deflection of the doors. We tested the validity of the developed analytical model by measuring the deflection of the hinge when loads were applied to the upper and lower hinges of the refrigerating compartment and compared these with the analysis results. The comparison of the vertical displacement of the measured result and the analysis result showed an error ratio of up to 12.8%, which indicates that the analytical model is consistent. Using the analytical model composed of the cabinet, hinges and doors, we performed analyses for two cases: both doors closed, and the refrigerating door open. Since the maximum vertical displacement of the refrigerating compartment door (R-door) with the food load is smaller than the gap between the lower surface of the R-door and the upper surface of the freezer compartment door (F-door), it is judged that the R-door and the F-door do not contact when the doors are opened or closed. In addition, the analysis result showed that the difference between the vertical displacement at the hinge on the opposite side and the hinge side of the R-door is favorably smaller than the management criterion of the refrigerator manufacturer.

• Current Photovoltaic Research
• /
• v.8 no.2
• /
• pp.45-49
• /
• 2020

Molybdenum (Mo) thin films are widely used as back contact in copper indium diselenide (CISe) solar cells. However, despite this, there are only few published studies on the properties of Mo and characteristics of CISe solar cells formed on such Mo substrates. In this studies, we investigated the properties of sputter deposited Mo bilayer, and fabricated non-vacuum CISe solar cells using bilayer Mo substrates. The changes in surface morphology and electrical resistivity were traced by varying the gas pressure during deposition of the bottom Mo layer. In porous surface structure, it was confirmed that the electrical resistivity of Mo bilayer was increased as the amount of oxygen bonded to the Mo atoms increased. The resulting solar cell characteristics vary as the bottom Mo layer deposition pressure, and the maximum solar cell efficiency was achieved when the bottom layer was deposited at 7 mTorr with a thickness of 100 nm and the top layer deposited at 3 mTorr with a thickness of 400 nm.