• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.561-566
• /
• 2001

A long bar impact test to alumina plates(AD 85 and AD 90) was carried out by using fabricated impact testing apparatus. The apparatus adopting a long bar of 2.1m in length made it possible to measure directly the applied impact force to the specimen during bar impact. The dimension of specimens was $33{\times}33mm$ and thickness was 3.4mm. Confinement of D2=18mm outer diameter and D1=10.5mm inner diameter was used to provide contact pressure to the specimen. Contact pressure of p=100 or 200MPa was applied to specimen before impact test. Damage caused in those cases were compared with the case of without contact pressure. The damage of specimen was different depending upon the pressure level of confinement. The existence of confinement had suppressed the development of radial cracks from the bottom of specimen and reduced the extent of damage as compared with cases without contact pressure(p=0MPa). Because the application of contact pressure to the specimen increased the apparent flexural stiffness of specimen during bar impact, it had produced the change of developed damage in the specimen; from the radial cracks to the local contact stress dominant damage. It would contribute to the improvement of the ballistic property in ceramic plates.

• 한국소음진동공학회논문집
• /
• 제17권4호
• /
• pp.317-323
• /
• 2007

Non-contact underwater explosions against surface ships could cause extensive equipment damage and render the ship inoperative. As an analytical method, DDAM(dynamic design and analysis method) is used for ship shock design. In this paper, in order to verify the finite element model of large shipboard equipment, modal test of equipment was performed. Major objective of this paper is to describe shock analysis methodology for large shipboard equipment attacked to the top and bottom foundations.

• 한국반도체및디스플레이장비학회:학술대회논문집
• /
• 한국반도체및디스플레이장비학회 2007년도 춘계학술대회
• /
• pp.149-156
• /
• 2007

Non-contact transportation of the large-sized glass plate using air-cushion is considered for sputtering system of LCD panel. The Argon gas from second gas injection holes is injected to levitate and transport the glass plate. Low maximum pressure and uniform pressure distribution on the bottom surface of the glass plate must be maintained for stable levitation and transportation of the glass plate. Therefore, the analysis of fluid flow between the glass plate and the air-pad is numerically performed for varying space between the injection holes in this study. The pressure uniformity on the bottom surface of the glass plate is evaluated for overall glass plate. The distance between the injection holes must be designed below 90 mm for obtaining the low maximum pressure and uniform pressure distribution.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2008년도 International Meeting on Information Display
• /
• pp.1631-1633
• /
• 2008

We demonstrate 4-in QVGA active-matrix electrophoretic display based on ink-jet printed organic transistors on glass substrates. Our TFT array had a bottom-gate, bottom-contact device architecture. The organic semiconductor and gate dielectric were solution processed. The field-effect mobility of the printed devices, calculated in the saturation region, was $0.1{\sim}0.3cm^2/Vs$ at Vg=-20 V.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1609-1614
• /
• 2003

In this study, a practical holographic interferometric tomography system, which is instantaneous and non-contact for measuring three dimensional flow field, was developed. The system consists of holographic recording/reconstruction system, fringe analysis code and computational tomography code and it is developed with Gill environment for general users. The developed system was applied to three-dimensional natural convection from a discrete flush-mounted circular heat source on the bottom of a cubic enclosure. The heat source was located at the off-center of the bottom plate so that three-dimensional temperature field can be achieved. A set of multi-directional holographic interferograms was recorded by employing a double-reference beam, double-exposure holographic technique. Optical pathlength data were extracted from the recorded interferometric data and finally three dimensional temperature field inside the cube was reconstructed.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제55권1호
• /
• pp.26-29
• /
• 2006

Transparent ZnO thin films were prepared by KrF pulsed laser deposition (PLD) technique and applied to a bottom-gate type thin film transistor device as an active channel layer. A high conductive crystalline Si substrate was used as an metal-like bottom gate and SiN insulating layer was then deposited by LPCVD(low pressure chemical vapour deposition). An aluminum layer was then vacuum evaporated and patterned to form a source/drain metal contact. Oxygen partial pressure and substrate temperature were varied during the ZnO PLD deposition process and their influence on the thin film properties were investigated by X-ray diffraction(XRD) and Hall-van der Pauw method. Optical transparency of the ZnO thin film was analyzed by UV-visible phometer. The resulting ZnO-TFT devices showed an on-off ration of $10^6$ and field effect mobility of 2.4-6.1 $cm^2/V{\cdot}s$.

• 한국분말재료학회지
• /
• 제11권3호
• /
• pp.233-241
• /
• 2004

In this study, bottom-up type powder processing and top-down type SPD (severe plastic deformation) approaches were combined in order to achieve both full density and grain refinement of Al-20 wt% Si powders without grain growth, which was considered as a bottle neck of the bottom-up method using the conventional powder metallurgy of compaction and sintering. ECAP (Equal channel angular pressing), one of the most promising method in SPD, was used for the powder consolidation. The powder ECAP processing with 1, 2, 4 and 8 passes was conducted for 10$0^{\circ}C$ and 20$0^{\circ}C$ It was found by microhardness, compression tests and micro-structure characterization that high mechanical strength could be achieved effectively as a result of the well bonded powder contact surface during ECAP process. The SPD processing of powders is a viable method to achieve both fully density and nanostructured materials.

• 한국전산구조공학회논문집
• /
• 제36권3호
• /
• pp.165-171
• /
• 2023

건설기계와 특장차의 상부와 하부 구조를 연결하는 로터리 조인트는 축과 하우징이 회전하면서 유압을 전달하는데 오일의 유로에 누유를 방지하기 위해 여러 개의 시일이 조립된다. 시일재료는 강성이 커서 조립에 어려움이 있기 때문에 자른 후 조립하는 방법을 모색하였다. 절단면의 모양은 L형과 /형으로 하였고 유압이 작용할 때 누유 기준은 절단면에 발생하는 접촉압력으로 하였다. 시일의 구조와 재료는 이중 탄성중합체로 구성되며 강성이 큰 PE 재질만 절단한 경우에 대하여 비선형 접촉 구조해석을 수행하였다. 연구결과 절단 길이가 짧을수록 누유 방지에 유리하며 PE와 하우징이 접촉하는 윗면보다 NBR과 PE가 접촉하는 아랫면으로 누유될 가능성이 큰 것으로 나타났다.

• 센서학회지
• /
• 제22권1호
• /
• pp.49-53
• /
• 2013

In this paper, we proposed a laser-based non-contact temperature measuring method for high speed rotating polycarbonate (PC) disk using transparency change of thermocolor. The thermocolor has abilities to change color and transparency due to a change in temperature. The thermocolor is applied on one side of polyvinylidene fluoride (PVDF) membrane. The thermocolor applied membrane is attached to inside of reaction chamber in disk. An optical system consisted of a laser beam radiator and a laser photometer is installed. Laser is irradiated at the bottom side of disk and the transmitted laser beam is detected by the laser photometer at the opposite side of disk. During the disk is rotating, laser is irradiated and detected simultaneously. The laser photometer senses the transmitted laser power and generates voltage as output. The temperature of disk can be detected during the disk is rotating up to 3000 RPM.

• 한국공작기계학회논문집
• /
• 제15권3호
• /
• pp.32-38
• /
• 2006

During stereolithography processes, the shape errors such as curl distortion and distortion of side face are generated due to the shrinkage of liquid resins. In this study, the effects of dimension of part and structure of supports on the shape error are examined. Cubic specimens which have different thicknesses are manufactured and their deformations are measured with CMM. Thicker part generates smaller curl distortion of top face and larger of bottom face. Also thicker part generates larger distortion of side face until part thickness increases to about 20mm. Larger stiffness of supports which is obtained by shorter spacing of the supports and line type contact instead of point type contact generates smaller shape error of the part.