• Journal of Welding and Joining
• /
• 제9권3호
• /
• pp.26-33
• /
• 1991

As it takes very long time for the Transient Liquid Phase(TLP) bonding, we tried to reduce the bonding time by changing insert material for the high diffusivity element. On this study boron powder was doped as a insert material on the bonding surface of Rene 80 superalloy, and diffusion treated at 1150.deg.C under vacuum. On this method differently from the TLP bonding the insert material was not melted during bonding but only the base metal reacted with the boron was inducedly melted. Therefore, as this bonding mechanism is different from the existing ones, it is suggested as a Melting Induced Diffusion Bonding. When this process was used for the diffusion bonding, the bonding time including homogenization decreased greatly compared to the conventional TLP bonding.

• 제어로봇시스템학회논문지
• /
• 제14권6호
• /
• pp.543-547
• /
• 2008

In the paper, we develop the ultrasonic bonding technique for LCD driver chips having small size and high pin-density. In general, the mounting technology for LCD driver ICs is a thermo-compression method utilizing the ACF (An-isotropic Conductive Film). The major drawback of the conventional approach is the long process time. It will be shown that the conventional ACF method based on thermo-compression can be remarkably enhanced by employing the ultrasonic bonding technique in terms of bonding time. The proposed approach is to apply the ultrasonic energy together with the thermo-compression methodology for the ACF bonding process. To this end, we design a bonding head that enables pre-heating, pressure and ultrasonic excitation. Through the bonding experiments mainly with LCD driver ICs, we present the procedures to select the best combination of process parameters with analysis. We investigate the effects of bonding pressure, bonding time, pre-heating temperature before bonding, and the power level of ultrasonic energy. The addition of ultrasonic excitation to the thermo-compression method reduces the pre-heating temperature and the bonding process time while keeping the quality bonding between the LCD pad and the driver IC. The proposed concept will be verified and demonstrated with experimental results.

• 한국전기전자재료학회논문지
• /
• 제22권8호
• /
• pp.625-631
• /
• 2009

In this thesis, lateral thermosonic bonding with ACFs was investigated as a process to make high reliability joints for FPD fabrication. Conditions for thermosonic and thermocompression bonding with ACFs were determined and used to make specimens in a driving test jig for testing of bond reliability by thermal shock. The results showed that thermosonic bonding temperature of $199\;^{\circ}C$ and bonding time of 1s produced bonds with good reliability. Additionally, thermosonic bonding temperature and time were reduced and thermal shock test results compared to this proposed curing condition. It is concluded that theromosonic bonding with ACFs can be effectively applied to reduce bonding temperature and time compared with that of thermocompression bonding.

• 대한기계학회논문집A
• /
• 제26권6호
• /
• pp.1187-1193
• /
• 2002

Anodic bonding process has been quantitatively evaluated based on the Taguchi analysis of the interfacial fracture toughness, measured at the interface of anodically bonded silicon-glass bimorphs. A new test specimen with a pre-inserted blade has been devised for interfacial fracture toughness measurement. A set of 81 different anodic bonding conditions has been generated based on the three different conditions for four different process parameters of bonding load, bonding temperature, anodic voltage and voltage supply time. Taguchi method has been used to reduce the number of experiments required for the bonding strength evaluation, thus obtaining nine independent cases out of the 81 possible combinations. The interfacial fracture toughness has been measured for the nine cases in the range of 0.03∼6.12 J/㎡. Among the four process parameters, the bonding temperature causes the most dominant influence to the bonding strength with the influence factor of 67.7%. The influence factors of other process parameters, such as anodic voltage and voltage supply time, bonding load, are evaluated as 18%, 12% and 2.3%, respectively. The maximum bonding strength of 7.23 J/㎡ has been achieved at the bonding temperature of 460$\^{C}$ with the bonding load of 45gf/㎠, the applied voltage of 600v and the voltage supply time of 25minites.

• Journal of Welding and Joining
• /
• 제13권2호
• /
• pp.132-138
• /
• 1995

Rene80 superalloy was liquid phase diffusion bonded by using boron(B) as an insert material, where B has high diffusivity and higher melting point as an insert material. Bonding procedure and bonding mechanism of Rene80/B/Rene80 joint were investigated. As results, liquid metal was produced by solid state reaction between base metal and insert material on bonding zone. The liquid metal was produced preferentially at the grain boundary. Except for production of liquid metal, other bonding procedure was nearly same as TLP(Transient Liquid Phase) bonding. Bonding time, however, was reduced compared to prior result of TLP bonding. By bonding S.4ks at l453K, Ren80/B/Rene80 joint was isothermally solidified and homogenized where thickness of insert material was 7.5.mu.m.

• Journal of Welding and Joining
• /
• 제23권2호
• /
• pp.52-58
• /
• 2005

This study was carried out to investigate the effect of bonding temperature and heating rate on transient liquid phase diffusion bonding of Ni-base superalloy. The heating rate was varied by $0.1^{\circ}C$/sec, $1^{\circ}C$/sec, $10^{\circ}C$/sec to the bonding temperatures $1100^{\circ}C,\;1150^{\circ}C,\;1200^{\circ}C$ under vacuum. As bonding temperature increased, maximum dissolution width of base metal increased, but a dissolution finishing time decreased. The eutectic width of insert metal in the bonded interlayer decreased linearly in proportion to the square root of holding time during isothermal solidification stage. The bonding temperature was raised, isothermal solidification rate slightly increased. As the heating rate decreased and the bonding temperature increased, the completion time of dissolution after reaching bonding temperature decreased. When the heating rate was very slow, the solidification proceeded before reaching bonding temperature and the time required for the completion of isothermal solidification became reduced.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 춘계학술발표대회 개요집
• /
• pp.285-287
• /
• 2002

This study is investigated in variations of micro-structures and mechanical properties of Ti/SUS321L joint with bonding temperature and time using brazing method. According to increasing bonding temperature and time, it was observed the thickness of their reaction layer increased. In tensile test, it was examined that the tensile strength had maximum value at the bonding time of 5min and decreased after bonding time over 5min because of increasing their oxides and intermetallic compounds.

• 한국재료학회지
• /
• 제5권2호
• /
• pp.191-196
• /
• 1995

비정질 PEEK 필름의 self-bonding강도는 접합시의 공정변수(시간, 온도, 그리고 압력)와 밀접한 관계가 있다. 본 연구에서는 이러한 공정변수의 효과를 규명하기 위하여 각기 다른 접합조건하에서 개발된 시편들의 self-bonding강도를 single lap-shear test를 통하여 측정된 각각의 전단 응력(shear strength)으로 나타내었다. 개발된 self-bonding강도는 접합온도가 증가함에 따라 증가하였으며, 접합시간의 1/4승에 일차함수적으로 비례증가하였다. 접합공정 중의 압력의 효과는 단지 초기 접합단계인 wetting에 기여하였을 뿐 self-bonding강도 자체에는 거의 영향을 미치지 않는 것으로 사려되었다. 결론적으로 비정질 PEEK 필름의 self-bonding현상은 현장에서의 실제 접합공정에서 어떠한 접착재료의 사용없이도 모재와 같은 강도를 개발하는데 무한한 가능성이 있는 것으로 판단되었다.

• 한국안전학회지
• /
• 제32권1호
• /
• pp.9-14
• /
• 2017

Diffusion bonding is a technique that has the ability to join materials with minimum change in joint micro-structure and deformation of the component. The quality of the joints produced was examined by metallurgical characterization and the joint micro-structure developed across the diffusion bonding was related to changes in mechanical properties as a function of the bonding time. An increase in bonding time also resulted in an increase in the micro-hardness of the joint interface from 55 VHN to 180 VHN, The increase in hardness was attributed to the formation of intermetallic compounds which increased in concentration as bonding time increased.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.1501_1502
• /
• 2009

Plasma treatment time was optimized to maximize the bonding strength between silicon and quartz. Bonding strength between the silicon and quartz is related to a surface energy which can be calculated by contact angle measurement. It was found that optimized time to get maximized surface energy was 15 sec. Silicon and quartz wafers were treated with $O_2$ plasma under different time splits and then bonded together. Bonding strength of the bonded wafers was measured by shear test. It was verified that the highest bonding strength was obtained when the silicon and quartz wafers were treated for 15 seconds. The maximum bonding strength exceeded the fracture strength of silicon.