• 한국세라믹학회지
• /
• 제36권11호
• /
• pp.1228-1234
• /
• 1999

In order to form a uniform oxidation layer and spinel crystalline phase that was supposed to help strong bonding in Kovar(Fe-29Ni-17Co)to-glass sealing the humidified nitrogen (2.3%H2O/N2) was used as an oxidation atmosphere. Kovar oxidation was diffusion-contolled and the activation energy was 2.51 kcal/mol at 600-900$^{\circ}C$ After oxidation at 600$^{\circ}C$ the oxidation layer was under 1$\mu\textrm{m}$ thickness and crystalline phase was spinel which was found to be suitable for the Kovar-to-glass sealing.

• Journal of Electrical Engineering and information Science
• /
• 제2권6호
• /
• pp.167-170
• /
• 1997

Magnetostrictions of metallic glass ribbons were measured by fiber-optic Mach-Zehnder interferometry. The saturation magnetostrictions measured here are accurate to within 10%. For accurate measurements the fibers in the ribbons were uncoated, the ribbons were flattened before bonding, and two passes of fiber in the sensing arm were bonded to a single layer metallic glass ribbon at the ends only. Various factors affecting the accuracy of the measurements were also discussed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.298-299
• /
• 2006

공통의 glass를 이용한 LTCC 이종소재의 무수축 접합 가능성을 확인하기 위하여 2종의 상용 glass를 이용하여 소결온도를 변화시키면서 미세구조 및 결정구조, x-y축 방향의 수축율을 관찰하였다. 실험 결과 GA-12 glass는 강유전체 $BaTiO_3$와 glass의 composite개념을 이용한 접합에 적절하지 않은 것으로 판단되었으며, GA-1 glass의 경우는 $750^{\circ}C$와 $800^{\circ}C$ 사이에서 glass의 충분한 침투조건이 확인되며, 결정구조 에서도 glass/$BaTiO_3$ composite이 형성되므로 layer 간의 delamination은 발견되지만 x-y축 방향의 무수축 접합의 가능성이 확인되었다.

• Structural Engineering and Mechanics
• /
• 제85권5호
• /
• pp.573-592
• /
• 2023

This paper presents a careful theoretical investigation into interfacial stresses in composite aluminum-slab reinforced concrete beam bonded by a prestressed hybrid carbon-glass composite material. The model is based on equilibrium and deformations compatibility requirements in and all parts of the strengthened beam, i.e., the aluminum beam, the slab reinforced concrete, the hybrid carbon-glass composite plate and the adhesive layer. The theoretical predictions are compared with other existing solutions. Numerical results from the present analysis are presented both to demonstrate the advantages of the present solution over existing ones and to illustrate the main characteristics of interfacial stress distributions. It is shown that the stresses at the interface are influenced by the material and geometry parameters of the composite beam. This research is helpful for the understanding on mechanical behaviour of the interface and design of the hybrid structures.

• 대한소아치과학회지
• /
• 제25권2호
• /
• pp.285-291
• /
• 1998

The purpose of this study was to asses the shear bond strengths of 3 types of glass ionomer cement and 1 type of composite resin to dentinal surface with or without ZOE pretreatment. 80 extracted tooth specimens are divided into two groups; the control group (40 specimens) is not treated with ZOE and the other(40 specimens) is ZOE pretreated during 24 hours before bonding procedure. Shear bond strengths were measured with universal testing machine (Instron, Model 4301) and statistically processed by ANOVA and t-test. The results were as follows: 1. Bond strength of the ZOE treated experimental group showed lower than the control group, except chemical cured glass ionomer cement(p<0.05). 2. After ZOE surface treatment, the bond strength of composite resin was superior than glass ionomer cement and all experimental group was decreased (p<0.05). 3. It has nothing to do with ZOE surface treatment, that chemical curing glass ionomer cement was showed lowest bond strength.

• Composites Research
• /
• 제19권3호
• /
• pp.15-22
• /
• 2006

유리섬유로 강화된 폴리프로필렌 복합재료를 이축압출장치를 이용하여 제조하였으며 폴리프로필렌 수지와 유리섬유간의 결합성을 증대시키고 가공성을 향상시킬 목적으로 말레익 안하이드라이드(maleic anhydride) 결합기를 가지는 상용화제를 첨가하였다. 제조된 폴리프로필렌/유리섬유 복합재료에 대한 전단유동과 신장유동의 특성을 조사하였으며, 특히 상용화제 첨가와 유리섬유의 함량에 대한 영향을 주로 평가하였다. 전단유동에서 상용화제는 폴리프로필렌과 유리섬유간의 결합력을 증대시키고, 흐름성을 개선시키는 역할을 하였으며, 신장유동에서는 유리섬유의 함량이 증가됨에 따라서 신장점도를 더욱 증가시켜주는 역할을 하였다. 그러나 신장속도가 증가함에 따라서 유리섬유 사이에서 형성되는 미세한 전단유동의 영향으로 오히려 신장점도는 감소하였다.

• Journal of the Korean Wood Science and Technology
• /
• 제44권1호
• /
• pp.40-47
• /
• 2016

구조용 집성재 라멘 접합부에 일반적으로 사용되는 접합철물을 대신하여 단판과 GFRP (Glass Fiber Reinforced Plastic)를 복합시킨 GFRP 보강적층판과 삽입 접착형 GFRP rod를 접합물로 사용하였다. 이들을 적용시킨 접합부에 대한 모멘트저항 성능평가 결과, 접합철물을 이용한 실험체(Type-1)와 비교하여 GFRP 보강적층판과 GFRP rod 핀을 사용한 실험체의 항복모멘트는 4% 낮게 측정되었으나 회전강성은 29% 높게 측정되었다. 또한 GFRP 보강적층판과 목재(Eucalyptus marginata)핀을 사용한 실험체는 Type-1 실험체와 비교하여 항복모멘트 11%, 회전강성 56% 높게 측정되며 가장 양호한 성능을 나타냈었다. 파괴형상과 완전탄소성 분석을 통해서도 핀에 의한 전단내력으로부터의 취성파괴가 아닌 연성거동을 나타내며, 접합내력이 상승하고 부재의 일체화가 이루어짐을 확인하였다. 반면, GFRP rod를 삽입 접착한 실험체는 접착 불량으로 측정이 불가하거나 접합성능이 매우 낮게 측정되었다.

• 한국도로학회논문집
• /
• 제19권3호
• /
• pp.31-43
• /
• 2017

PURPOSES : The objective of this study is to verify the effect of fiber grid reinforcement on the long-term performance of asphalt pavement overlaid on old concrete pavement by performing field investigation, laboratory test, and finite element analysis. METHODS : The reflection cracking, roughness, and rutting of fiber grid reinforced overlay sections and ordinary overlay sections were compared. Cores were obtained from both the fiber grid reinforced and ordinary sections to measure bonding shear strength between the asphalt intermediate and asphalt overlay layers. Fracture energy, displacement after yield, shear stiffnesses of the cores were also obtained by analyzing the test results. Finite element analysis was performed using the test results to validate the effect of the fiber grid reinforcement on long-term performance of asphalt pavement overlaid on the old concrete pavement. The fatigue cracking and reflection-cracking were predicted for three cases: 1) fiber grid was not used; 2) glass fiber grid was used; 3) carbon fiber grid was used. RESULTS : The reflection-cracking ratio of fiber grid reinforced sections was much smaller than that of ordinary sections. The fiber grid reinforcement also showed reduction effect on rutting while that on roughness was not clear. The reflection-cracking was not affected by traffic volume but by slab deformation and joint movement caused by temperature variation. The bonding shear strength of the fiber grid reinforced sections was larger than that of the ordinary sections. The fracture energy, displacement after yield, and shear stiffnesses of the cores of the fiber grid reinforced sections were also larger than those of the ordinary sections. Finite element analysis results showed that fatigue cracking of glass or carbon fiber grid reinforced pavement was much smaller than that of ordinary pavement. Carbon fiber grid reinforcement showed larger effect in elongating the fatigue life of the ordinary overlay pavement compared to glass fiber grid reinforcement. The binder type of the overlay layer also affected the fatigue life. The fiber grid reinforcement resisted reflection-cracking and the carbon fiber grid showed the greater effect. CONCLUSIONS :The results of field investigation, laboratory test, and finite element analysis showed that the fiber grid reinforcement had a better effect on improving long-term performance of asphalt pavement overlaid on the old concrete pavement.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 춘계학술대회 및 기술 세미나 논문집 디스플레이 광소자
• /
• pp.42-42
• /
• 2008

Considerable attention has been focused on the applications of flexible liquid crystal (LC)-based displays because of their many potential advantages, such as portability, durability, light weight, thin packaging, flexibility, and low power consumption. To develop flexible LCDs that are capable of delivering high-quality moving images, like conventional glass-substrate LCDs, the LC device structure must have a stable alignment layer of LC molecules, concurrently support uniform cell gaps, and tightly bind two flexible substrates under external tension. However, stable LC molecular alignment has not been achieved because of the layerless LC alignment, and consequently high-quality images cannot be guaranteed. To solve these critical problems, we have proposed a PDMS pixel-wall based bonding method via the IB irradiation was developed for fasten the two substrates together strongly and maintain uniform cell gaps. The effect of the IB irradiation on PDMS with PI surface was also evaluated by side structure configuration and a result of x-ray photoelectron spectroscopic analysis of PDMS interlayer as a function of binder with substrates. large number of PDMS pixel-walls are tightly fastened to the surface of each flexible substrate and could maintain a constant cell gap between the LC molecules without using any other epoxy or polymer. To enhance the electro-optical performance of the LC device, we applied an alignment method that creates pretilt angle on the PI surface via ion beam irradiation. Using this approach, our flexible LCDs have a contrast ratio of 132:1 and a response time of about 15 ms, resulting in highly reliable electro-optical performance in the bent state, comparable to that of glass-substrate LCDs.

• 마이크로전자및패키징학회지
• /
• 제10권3호
• /
• pp.57-65
• /
• 2003

본 연구에서는 웨이퍼 레벨 진공 패키징된 MEMS자이로스코프 소자의 신뢰성 시험 및 분석을 통하여 웨이퍼 레벨 진공 패키징의 파괴 메카니즘을 연구하였다. 진공 패키징의 주된 파괴 모드는 누설, 가스투과, 그리고 outgassing이다. 누설은 접합 계면이나 재질의 결함을 통하여 주로 발생되며, 접합폭을 증가시키거나 단결정 실리콘을 사용하면 누설이 감소한다. Outgassing은 실리콘 및 유리기판의 표면 및 내부에서 발생하며 주로 $H_2O$와, $CO_2$, $C_3H_5$ 및 유기 오염물질이었다. Epi-poly의 경우 SOI 웨이퍼보다 약 10배의 outgassing을 발생시킨다. 또한 유리기판을 샌드블라스트 공정을 사용하여 가공한 경우, 약 2.5배의 outgassing 양이 증가한다. Outgassing 제거를 위해서는 접합 전에 웨이퍼를 pre-baking하는 과정이 필수적이며, outgassing의 발생을 최대로 하기 위한 최적의 pre-baking조건은 실리콘과 유리 웨이퍼를 $400^{\circ}C$와 $500^{\circ}C$ 사이에서 pre-baking하는 것이다.