• Journal of the Korean Society of Industry Convergence
• /
• v.17 no.4
• /
• pp.194-202
• /
• 2014

Bonding Machine is new concept of semi industry. In this study, bonding machine is designed with aximatic design, then manufactured based on it. Axiomatic design offers a scientific base for design in an efficient way. Many application of the independence axiom have been pulished, however, the information axiom has been mainly applied to FR - DP problems except for few case studies.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.389-396
• /
• 2002

Engineers should be careful in the design of bonding piles into pile caps because they are weak points in the pile foundation. Therefore in this study, the mechanism of bonding piles into pile caps was explained, and the design method of the composite bonding method was proposed. And the proposed design method was verified in comparison with the result of the full scale test. Also, the characteristic for the bearing capacity and the mechanism of compressive load of bonding method were analyzed.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.12
• /
• pp.92-98
• /
• 2010

The design of press bonding tool in LCD module equipment is a very complex and difficult task because many design able variables are involved while their effects are not known. It takes longtime experiments and much expenses to verify the effects of these design variables. However the optimization of bonding tool using OLB(outer lead bonding) and PCB Bonding is a very important problem in LCD manufacturing process, so much design efforts have been made for improving the bonding tool performance. In this paper, a reasonable and fast process which gives optimized solution under the design requirements has been presented. Both analytical and statistical methods are employed in this process. A reliable analytic model using experiment-oriented FE analysis can be obtained, in which the regression equations that predict the tool efficiency from various DOE method are found. Improvement of tool efficiency could be estimated by the regression equations using meaningful factors converged by RSM(Response Surface Method). With this process a reasonable optimized solution that meets a variety of design requirements can be easily obtained.

• Journal of Welding and Joining
• /
• v.30 no.6
• /
• pp.113-119
• /
• 2012

Ultrasonic bonding is the novel packaging method for flip-chip with high yield and low-temperature bonding. The bonding module is a core part of the bonding machine, which can transfer the ultrasonic energy into the bonding spot. In this paper, we propose topology optimization technique which can make new design of boding modules due to the constraints on resonance frequency and mode shapes. The designed bonding module using topology optimization was fabricated in order to evaluate the bonding performance and reliable operation during the continuous bonding process. The actual production models based on the proposed design satisfied the target frequency range and ultrasonic power. The bonding test was performed using flip-chip with lead-free Sn-based bumps, the results confirmed that the bonding strength was sufficient with the designed bonding modules. Also the performance degradation of the bonding module was not observed after the 300-hour continuous process with bonding conditions.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.12
• /
• pp.84-91
• /
• 2010

The bonding process of LCD panel is attaching an inner lead to an outer lead in the production line of LCD panel module. It is composed of an OLB process and a PCB bonding process. Since bonding tool assembly is one of the core parts of the bonding equipment that determines the durability and performance of the final product, much design efforts to enhance uniformity and efficiency of the process have been made. In this paper, FE analyses have been employed to determine the bonding tool size. Bonding tool of long bar shape has been simplified as a piece with same heater pitch, and appropriate boundary conditions such as convection and radiation are considered. Thermal analysis results by the FEM have been validated by the experiments. With the use of FE analysis varies design parameters and the corresponding effects have been evaluated. It was observed that the approach presented in this paper could be employed for the design of LCD module bonding tool.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.1
• /
• pp.11-15
• /
• 2001

We present the design and strength evaluation of an anodically bonded pressurized cavity array, based on the energy release rate measured from the anodically bonded plates of two dissimilar materials. From a theoretical analysis, a simple fracture mechanics model of the pressurized cavity array has been developed. The energy release rate (ERR) of the bonded cavity with an infinite bonding length has been derived in terms of cavity pressure, cavity size, bonding length, plate size and material properties. The ERR with a finite bonding length has been evaluated from the finite element analysis performed for varying cavity and plate sizes. It is found that, for an inter-cavity bonding length greater than the half of the cavity length, the bonding strength of cavity array approaches to that of the infinite plate. For a shorter bonding length, however, the bonding strength of the cavity array is monotonically decreased with the ratio of the bonding length to the cavity length. The critical ERR of 6.21J/㎡ has been measured from anodically bonded silicon-glass plates. A set of critical pressure curves has been generated for varying cavity array sizes, and a design method of the pressurized cavity array has been developed for the failure-free wafer-level packaging of MEMS devices.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.4
• /
• pp.653-659
• /
• 2008

This paper describes the design of high power transistor packages using high power chip transistor dies, chip capacitors and a new wire bonding technique. Input impedance variation and output power performances according to wire inductance and resistance for internal matching are also discussed. A multi crossing type(MCT) wire bonding technique is proposed to replace the conventional stepping stone type(SST) wire bonding technique, and eventually to improve the output power performances of high power transistor packages. Using the proposed MCT wire bonding technique, it is possible to design high power transistor packages with highly improved output power compared to SST even the package size is kept to be the same.

• Journal of Welding and Joining
• /
• v.23 no.6
• /
• pp.77-86
• /
• 2005

Low temperature bonding of the silicon and glass using the Spin-on Glass (SOG) has been conducted experimentally to figure out the effects of the SOG solution composition and process variables on bond strength using the Design of Experiment method. In order to achieve the high quality bond interface without rack, sufficient reaction time of the optimal SOG solution composition is needed along with proper pressure and annealing temperature. The shear strength under the optimal SOG solution composition and process condition was higher than that of conventional anodic bonding and similar to that of wafer direct bonding.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.4
• /
• pp.109-114
• /
• 2021

We investigated the effects of atmospheric hydrogen plasma treatment on Cu-Cu direct bonding. Hydrogen plasma was effective in reducing the surface oxide layer of Cu thin film, which was confirmed by GIXRD analysis. It was observed that larger plasma input power and longer treatment time were effective in terms of reduction and surface roughness. The interfacial adhesion energy was measured by DCB test and it was observed to decrease as the bonding temperature decreased, resulting in bonding failure at bonding temperature of 200℃. In case of wet treatment, strong Cu-Cu bonding was observed above bonding temperature of 250℃.

• Journal of the Korean Society of Industry Convergence
• /
• v.15 no.1
• /
• pp.37-42
• /
• 2012

Trends in semiconductor equipment industry are to reduce the cost of producing semiconductor, semiconductor process development, facility development, and the minimum investment in terms of cost and quality. Semiconductor equipments are being considered to review and development is proceeding at the same time. In the first part of the semiconductor assembly process, in which the importance of die bonding process is emerging, a wide leadframe type die bonding machine is demanded for productivity. Die bonding machine was designed through experiments and by trial and error. It costs a lot of time and financial burden. The purpose of this study is to solve these problems by using the CAE tool 3G. By using finite element method, thermal analysis of die bonding machine to the various widths leadframe die bonder machine rail is performed for design.