• 심성연구
• /
• 제31권2호
• /
• pp.177-214
• /
• 2016

그림형제가 수집한 민담 <황금 새>를 분석심리학적 관점에서 해석하였다. 민담의 제시부에 나타난 문제점은 왕과 아들 세 명의 치우친 남성적 구조 속에서 이 왕국은 여성성이 결핍되어 있다. 황금 사과의 상실은 균형을 이루기 위해 더욱 더 여성적 요소를 보충할 필요성을 느낀다. 가장 어리고 바보스러운 막내의 모험과 여행은 분석심리학에서 말하는 새로운 자아의 개성화 과정으로 볼 수 있다. 자아는 여행의 경과 중에 단계마다 새로운 왕국이라는 특정 집단의식의 지배에 사로잡히고 죽음의 위기에서 어려운 과제를 수행한 후에 해방되어 다음 단계로 나아간다. 이 과정은 성인화 과정으로 자아의 높아진 의식성의 회복 뒤에 여성성의 보충이라 하는 공주와의 결혼 즉 대극의 합일이 가능한 수준으로 발전할 수 있다. 여성성의 보충으로 보이는 새, 말, 공주는 독립되어 있는 것처럼 보이지만 그들은 서로 하나로 연결되어 있다. 이들을 만난 자아가 아직은 온전한 성공에 이른 것은 아니다. 집단 지배의식의 지시에 따라 출발하는 두 형들의 실패 뒤에 주관적 의식이 적극적으로 개입한 새로운 자아(막내)가 나섰다고는 하지만 아직도 페르소나의 구분과 버림은 쉽지 않은 난관이다. 반복된 고난에 이어 형들을 사형에 처한 다음에 즉 지적인 능력이 제물로 바쳐진 다음에 상위의 의식성을 획득하고 그의 아니마인 공주와 일차적 결혼을 한다. 대개의 이야기는 결혼으로 끝나지만 여기서는 다음 단계가 남아있다. 여우가 자신을 죽여 머리와 발을 잘라 달라는 간절한 부탁을 주인공이 마지못해 행하자 여우는 마법이 풀려 왕자가 된다. 여우가 공주의 오빠로 변신한 것은 동물이 인간화한 것으로 또 다른 의식화를 경험한다. 비로소 대극의 합일이 이루어지고, 신성한 결합이 전체성을 획득하고 즉 개성화의 완성을 이루게 된다.

• 대한치과보철학회지
• /
• 제45권2호
• /
• pp.169-181
• /
• 2007

Statement of problem: Titanium is well known as a proper metal for the dental restorations, because it has an excellent biocompatibility, resistance to corrosion, and mechanical property. However, adhesion between titanium and dental porcelains is related to the diffusion of oxygen to the reaction layers formed on cast-titanium surfaces during porcelain firing and those oxidized layers make the adhesion difficult to be formed. Many studies using mechanical, chemical and physical methods to enhance the titanium-ceramic adhesion have been actively performed. Purpose: This study meant to comparatively analyse the adhesion characteristics depending on different titanium surface coatings after coating the casts and wrought titanium surfaces with Au and TiN. Material and method: In this study, the titanium specimens (CP-Ti, Grade 2, Kobe still Co. Japan) were categorized into cast and wrought titanium. The wrought titanium was cast by using the MgO-based investment(Selevest CB, Selec). The cast and wrought titanium were treated with Au coating($ParaOne^{(R)}$., Gold Ion Sputter, Model PS-1200) and TiN coating(ATEC system, Korea) and the ultra low fusing dental porcelain was fused and fired onto the samples. Biaxial flection test was done on the fired samples and the porcelain was separated. The adhesion characteristics of porcelain and titanium after firing and the specimen surfaces before and after the porcelain fracture test were observed with SEM. The atomic percent of Si on all sample surfaces was comparatively analysed by EDS. In addition, the constituents of specimen surface layers after the porcelain fracture and the formed compound were evaluated by X-ray diffraction diagnosis. Result: The results of this study were obtained as follows : 1. The surface characteristics of cast and wrought titanium after surface treatment(Au, TiN, $Al_2O_3$ sandblasting) were similar and each cast and wrought titanium showed similar bonding characteristics. 2. Before and after the biaxial flection test, the highest atomic weight change of Si component was found in $Al_2O_3$ sandblasted wrought titanium(28.6at.% $\rightarrow$ 8.3at.%). On the other hand, the least change was seen in Au-Pd-In alloy(24.5at.% $\rightarrow$ 9.1at.%). 3. Much amount of Si components was uniformly distributed in Au and TiN coated titanium, but less amount of Si's was unevenly dispersed on Al2O3 sandblasting surfaces. 4. In X-ray diffraction diagnosis after porcelain debonding, we could see $Au_2Ti$ compound and TiN coating layers on Au and TiN coated surfaces and $TiO_2$, typical oxide of titanium, on all titanium surfaces. 5. Debonding of porcelain on cast and wrought titanium surface after the biaxial flection is considered as a result of adhesion deterioration between coating layers and titanium surfaces. We found that there are both adhesive failure and cohesive failure at the same time. Conclusion: These results showed that the titanium-ceramic adhesion could be improved by coating cast and wrought titanium surfaces with Au and TiN when making porcelain fused to metal crowns. In order to use porcelain fused to titanium clinically, it is considered that coating technique to enhance the bonding strength between coating kKlayers and titanium surfaces should be developed first.

• 대한치과보철학회지
• /
• 제52권2호
• /
• pp.113-120
• /
• 2014

연구 목적: 본 연구는 근관치료된 치아에 레진 시멘트로 fiber reinforced composite post (FRC) post의 접착시 포스트의 다양한 표면처리를 비교하여, 새롭게 제안되고 있는 다용도 프라이머의 효용성에 대해 평가하고자 하였다. 연구 재료 및 방법: 근관치료된 소구치 중 치근길이 1.8 cm 이상 되는 치아만을 총 24개 선택하였다. 표면 처리하지 않은 대조군과 표면처리를 시행한 FRC posts (DT Light Post, Size3, Bisco Inc., Schaumburg, IL, US)를 다음과 같이 6개의 그룹으로 무작위 분류하였다: Group A: airborne-particle abrasion (Cojet sand, 3M ESPE), Group S: silanization (Bis-silane, Bisco Inc.), Group M: universal primer (Monobond-plus primer, Ivoclar Vivadent Inc.), Group AS: silanization after airborne-particle abrasion, Group AM: universal primer treatment after airborne-particle abrasion. 하였다. CEJ에서 1.5 cm 근관성형 후 레진 시멘트를 이용하여 표면처리된 총 24개의 FRC post를 접착하고 광중합하였다. 생리식염수에 24시간 보관한 후 포스트 장축에 수직으로 1 mm 두께로 절단하여 만능시험기로 push-out test를 시행하였다. 포스트가 탈락되는 접착 실패 강도를 측정하고 SEM을 관찰하여 접착 실패 양상을 분류하고, 접착 강도를 Kruskal-Wallis test와 Tukey HSD value of rank test를 이용하여 통계 분석하였다(${\alpha}=0.05$). 결과: Airborne-particle abrasion후 실란 처리한 실험군에서 유의할만하게 높은 접착 강도를 보였다. 실란 처리, airborne-particle abrasion후 다용도 프라이머를 처리한 실험군의 순서로 접착 강도가 높게 나타났다. FRC post의 표면에 특정 전처리를 하지 않은 대조군에서 가장 낮은 결합 강도를 보이고, 이어서 다용도 프라이머, airborne-particle abrasion 순으로 낮은 평균 접착 강도를 보였다. 결론: FRC post의 접착 전 표면 처리 과정으로서 실란 처리를 거친 실험군에서 높은 결합 강도를 보였으며, 다용도 프라이머를 이용한 표면 처리는 실란과 비교하여 유의성 있는 접착 강도의 변화를 보이지 않았다.

• 대한치과교정학회지
• /
• 제36권3호
• /
• pp.188-197
• /
• 2006

교정 치료 시 사용되는 섬유 강화 컴포지트(FRC, fiber reinforced composite)는 구강 내에서 저작압 등의 지속적인 응력과 수분 흡수 등의 이유로 파절이 일어나는 경우가 있다. 이 때 모든 FRC를 제거하지 않고 수리(repair)하는 경우에 적절한 강도를 얻기 위해 첨가해야 할 FRC의 양 및 그 파절 양상을 알아보고자 하였다. 두 개의 FRC strips를 1, 2, 3, 그리고 4mm 만큼 겹쳐(E1, E2, E3, E4군) 시편을 만드는 방법으로 수리를 재현한 후 light emitting diode 광중합기로 중합하고, 3점 굽힘 실험을 시행하여 겹침 길이와 접합 강도간의 관계에 대해 조사하였다. 최대 하중치는 E4군에서 2.67N으로 최대였고, 대조군(2.39N), E3군(2.35N), E2군(2.10N), 그리고 E1군(1.75N)의 순이었다. 강성 역시 최대 하중치와 같이 E4군(2.32 N/mm)에서 최대치를 기록하였으나, E3군(2.06N/mm)의 강성이 대조군(1.88N/mm)보다 더 큰 값을 보였다. 겹침 길이가 길수록 완전히 두 조각으로 파절되기 보다 가운데 또는 critical section 에서 굽힘 양상을 보였다. 반면 겹침 길이가 짧은 경우 두 조각으로 부러지는 파절 양상을 보였다. 이상의 실험에서 길이 10 mm인 연결자 형태의 FRC의 수리 시 적절한 강도를 얻기 위해서는 최소 3 mm의 strips를 겹쳐야 하고, 이 때 주로 나타나는 실패 양상인 굽힘을 최소화하기 위해 연결 부위에 바로 인접하여 두께가 급격하게 변하는 critical section의 보강이 필요할 것으로 사료된다.

• 한국농공학회지
• /
• 제26권1호
• /
• pp.52-72
• /
• 1984

This study was performed to obtain the basic data which can be applied to the use of epoxy resin mortars. The data was based on the properties of epoxy resin mortars depending upon various mixing ratios to compare those of cement mortar. The resin which was used at this experiment was Epi-Bis type epoxy resin which is extensively being used as concrete structures. In the case of epoxy resin mortar, mixing ratios of resin to fine aggregate were 1: 2, 1: 4, 1: 6, 1: 8, 1:10, 1 :12 and 1:14, but the ratio of cement to fine aggregate in cement mortar was 1 : 2.5. The results obtained are summarized as follows; 1.When the mixing ratio was 1: 6, the highest density was 2.01 g/cm$^3$, being lower than 2.13 g/cm$^3$ of that of cement mortar. 2.According to the water absorption and water permeability test, the watertightness was shown very high at the mixing ratios of 1: 2, 1: 4 and 1: 6. But then the mixing ratio was less than 1 : 6, the watertightness considerably decreased. By this result, it was regarded that optimum mixing ratio of epoxy resin mortar for watertight structures should be richer mixing ratio than 1: 6. 3.The hardening shrinkage was large as the mixing ratio became leaner, but the values were remarkably small as compared with cement mortar. And the influence of dryness and moisture was exerted little at richer mixing ratio than 1: 6, but its effect was obvious at the lean mixing ratio, 1: 8, 1:10,1:12 and 1:14. It was confirmed that the optimum mixing ratio for concrete structures which would be influenced by the repeated dryness and moisture should be rich mixing ratio higher than 1: 6. 4.The compressive, bending and splitting tensile strenghs were observed very high, even the value at the mixing ratio of 1:14 was higher than that of cement mortar. It showed that epoxy resin mortar especially was to have high strength in bending and splitting tensile strength. Also, the initial strength within 24 hours gave rise to high value. Thus it was clear that epoxy resin was rapid hardening material. The multiple regression equations of strength were computed depending on a function of mixing ratios and curing times. 5.The elastic moduli derived from the compressive stress-strain curve were slightly smaller than the value of cement mortar, and the toughness of epoxy resin mortar was larger than that of cement mortar. 6.The impact resistance was strong compared with cement mortar at all mixing ratios. Especially, bending impact strength by the square pillar specimens was higher than the impact resistance of flat specimens or cylinderic specimens. 7.The Brinell hardness was relatively larger than that of cement mortar, but it gradually decreased with the decline of mixing ratio, and Brinell hardness at mixing ratio of 1 :14 was much the same as cement mortar. 8.The abrasion rate of epoxy resin mortar at all mixing ratio, when Losangeles abation testing machine revolved 500 times, was very low. Even mixing ratio of 1 :14 was no more than 31.41%, which was less than critical abrasion rate 40% of coarse aggregate for cement concrete. Consequently, the abrasion rate of epoxy resin mortar was superior to cement mortar, and the relation between abrasion rate and Brinell hardness was highly significant as exponential curve. 9.The highest bond strength of epoxy resin mortar was 12.9 kg/cm$^2$ at the mixing ratio of 1:2. The failure of bonded flat steel specimens occurred on the part of epoxy resin mortar at the mixing ratio of 1: 2 and 1: 4, and that of bonded cement concrete specimens was fond on the part of combained concrete at the mixing ratio of 1 : 2 ,1: 4 and 1: 6. It was confirmed that the optimum mixing ratio for bonding of steel plate, and of cement concrete should be rich mixing ratio above 1 : 4 and 1 : 6 respectively. 10.The variations of color tone by heating began to take place at about 60˚C, and the ultimate change occurred at 120˚C. The compressive, bending and splitting tensile strengths increased with rising temperature up to 80˚ C, but these rapidly decreased when temperature was above 800 C. Accordingly, it was evident that the resistance temperature of epoxy resin mortar was about 80˚C which was generally considered lower than that of the other concrete materials. But it is likely that there is no problem in epoxy resin mortar when used for unnecessary materials of high temperature resistance. The multiple regression equations of strength were computed depending on a function of mixing ratios and heating temperatures. 11.The susceptibility to chemical attack of cement mortar was easily affected by inorganic and organic acid. and that of epoxy resin mortar with mixing ratio of 1: 4 was of great resistance. On the other hand, when mixing ratio was lower than 1 : 8 epoxy resin mortar had very poor resistance, especially being poor resistant to organicacid. Therefore, for the structures requiring chemical resistance optimum mixing of epoxy resin mortar should be rich mixing ratio higher than 1: 4.

• 한국광물학회지
• /
• 제19권1호통권47호
• /
• pp.15-29
• /
• 2006

2 Kbar, $375{\sim}700^{\circ}C$ 조건하에서, 드라바이트의 Mg를 전 구간 치환하는 Mn 조성(Mn%=0, 25, 50, 75, 및 100%)을 가지고 열수법으로 약 50일간 성장시켜 Mn-전기석(tsilaisite)을 합성하였다. 그 결과, 조성별로 생성온도가 다른 6개의 합성 전기석이 얻어졌으며, 앨바이트, 스페샤틴, 능망간석, 금운모 등 다양한 불순물이 함께 생성되었다. 합성 Mn-전기석의 X-자리의 자리결손($0.53{\sim}0.68$)이 천연산(약 $0.2{\sim}0.3$)보다 높게 나타났으며, Y-자리의 Mn mole wt.%는 예상보다 낮은 값을 보이며, 단종 성분의 tsilaisite를 합성하지 못했다. 다양한 복합상으로 이루어진 분말 합성 전기석에 대해 리트벨트 구조분석을 실시하였다. $R_{wp}$값은($R_{p}/R_{exp}$)은 $13.35{\sim}18.62%$의 범위를 보여주며, $R_{B}$ 값은 $4.85{\sim}6.25%$ (S-18: 8.57%), S (GofF) 값은 $1.31{\sim}l.59$ (S-18: 1.81)으로 각각 나타났다. 단위포의 평균값은 공간군 R3m (z=3)으로 ${\alpha}=15.8994\;{\AA},\;c=7.1846\;{\AA}$이며, S-18은 ${\alpha}=15.9491\;{\AA},\;c=7.1773\;{\AA}$이다. 평균 값은 $2.67{\sim}2.69\;{\AA}$ (S-18: $2.65\;{\AA}$), 평균 값은 $2.00{\sim}2.02{\AA}$ (S-18: $1.96\;{\AA}$)으로 각각 계산되었으며, 대칭도(ditrigonality)를 나타내는 ${\delta}$값을 보면 $0.022{\sim}0.031$ (S-18: 0.061)의 범위를 가지는데 Mn 함량이 높아지면서 대칭도가 낮아진다.