• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2016.05a
• /
• pp.189-190
• /
• 2016

Lightweight concrete is currently used at apartment buildings or housing construction sites causes some uneconomical problems due to excessive cracks and subsidences. So, it is in the situation that it is necessary to set up countermeasures against such subsidences. Therefore, in this study, it is intended to analyze the prevention of a subsidence inducing the expansion of the aluminum components depending on the changes of substitution rate and bubble mixing ratio by using the bubble-based Leavening Agent that Aluminum slag as an industrial by-product is substituted into some desulfurized plaster. As the results, it was found that the blending ratios, such as, the substitution ratio of bubble-based leavening agent (1%) and the bubble mixing ratio (65%) are appropriate while the flow property, subsidence depth and compression strength are considered.

• Fibers and Polymers
• /
• v.7 no.3
• /
• pp.295-304
• /
• 2006

High-bulk worsted yams with different shrinkable and non-shrinkable acrylic fibers blend ratios are produced and then single jersey weft knitted fabrics with three different structures and loop lengths are constructed. The physical properties of produced yams and compression properties of produced fabrics at eight pressure values (50, 100, 200, 500, 1000, 1500 and $2000 g/cm^2$) were measured using a conventional fabric thickness tester. Then, weft-knitted fabric compression behavior was analyzed using a two parameters model. It is found that at 40 % shrinkable fibre blending ratio the maximum yam bulk, shrinkage, abrasion resistance and minimum yarn strength are obtained. It is also shown that high-bulk acrylic yarn has the highest elongation at 20 % shrinkable fibre blend ratio. The statistical regression analysis revealed that the compression behavior of acrylic weft-knitted fabrics is highly closed to two parameter model proposed for woven fabrics. It is also shown that for weft-knitted structure, there is an incompressible layer (V') which resists against high compression load. Acrylic weft-knitted fabrics with knit-tuck structure exhibit higher compression rigidity and lower softness than the plain and knit-miss structures. In addition, at 20 % shrinkable fibre blend ratio, the high-bulk acrylic weft-knitted fabrics are highly compressible.

• Geomechanics and Engineering
• /
• v.10 no.5
• /
• pp.689-707
• /
• 2016

Soil stabilization is one of the useful method of ground improvement for soil with low bearing capacity and high settlement and unrequired swelling potential. Generally, the stabilization is carried out by adding some solid materials. The main objective of this research was to investigate the feasibility of stabilization of organic soils and sewage sludge to obtain low cost alternative embankment material by the addition of two different slags. Slags were used as a replacement for weak soil at ratios of 0%, 25%, 50%, 75% and 100%, where sewage sludge and organic soil were blended with slags separately. The maximum dry unit weights and the optimum water contents for all soil mixtures were determined. In order to investigate the influence of the slags on the strength of sewage sludge and organic soil, and to obtain the optimal mix design; compaction tests, the California bearing ratio (CBR) test, unconfined compressive strength (UCS) test, hydraulic conductivity test (HCT) and pH tests were carried out on slag-soil specimens. Unconfined compressive tests were performed on non-cured samples and those cured at 7 days. The test results obtained from untreated specimens were compared to tests results obtained from soil samples treated with slag. Laboratory tests results indicated that blending slags with organic soil or sewage sludge improved the engineering properties of organic or sewage sludge. Therefore, it is concluded that slag can be potentially used as a stabilizer to improve the properties of organic soils and sewage sludge.

• Macromolecular Research
• /
• v.12 no.3
• /
• pp.303-310
• /
• 2004

We have prepared an aqueous dispersion of poly(aniline-dodecyl benzene sulfonic acid complex) (PANI-DC) that has an intrinsic viscosity (〔η〕) near 1.3 dL/g using aniline as a monomer, dodecyl benzene sulfonic acid(DBSA) as a dopant/emulsifier, and ammonium peroxodisulfate(APS) as an oxidant. We found that the electrical conductivity of a PANI-DC pellet was 0.7 S/cm. A waterborne-polyurethane (WBPU) dispersion, obtained from isophorone diisocyanate/polytetramethylene oxide glycol/dimethylol propionic acid/ethylene diamine/triethylene amine, was used as a matrix polymer. We prepared blend films of WBPU/PANI-DC with variable weight ratios (from 99/1 to 66/34) by solution blending/casting and investigated the effects that the PANI-DC content has on the mechanical and dynamic mechanical properties, hardness, electrical conductivity, and antistaticity of these films. The tensile strength, percentage of elongation, and hardness of WBPU/PANI-DC blend films all decreased markedly upon increasing the PANI-DC content. The antistatic half-life time ($\tau$$\sub$$\frac{1}{2}$/) of pure WBPU film was about 110 s, but we found that those of WBPU/ultrasound-treated PANI-DC blend films decreased exponentially from 1.2 s to 0.1 s to almost 0 s upon increasing the PANI-DC content from 1 wt% to 15 wt% to > 15 wt%, respectively.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.05a
• /
• pp.294-299
• /
• 2003

The efficiency of complex slurry preparation route for the development of high performance RS-SiCf/SiC composites has been investigated. The green bodies for RS-SiC and RS-SiCf/SiC composite materials prior to the infiltration of molten silicon were prepared with various C/SiC complex matrix slurries, which associated with both different sizes of starting SiC particles and blending ratios of starting SiC and carbon particles. The reinforcing materials in the composite system were uncoated and C coated Tyranno SA SiC fiber. The characterization of RS-SiC and RS-SiCf/SiC composite materials was examined by means of SEM, EDS and three point bending test. Based on the mechanical property-microstructure correlation, process optimization methodology is discussed.

• Fashion & Textile Research Journal
• /
• v.25 no.1
• /
• pp.62-71
• /
• 2023

Recently, interest in natural fabric materials that are not harmful has increased, and hemp is being studied as a new eco-friendly product. This study produced hemp fabric with improved flexibility and increased antibacterial properties by blending it with Hanji yarn. Various weaving methods were proposed to overcome the rough physical properties of hemp, and the functions of the developed products were evaluated through antibacterial tests. The mixing ratios of hemp and Hanji yarns was 50% hemp: 50% Hanji weft, 70% hemp: 30% Hanji weft, 30% hemp: 70% Hanji weft, and 100% hemp. Overall, the higher the ratio of Hanji yarn, the higher the fastness property, and the higher the ratio of hemp yarn, the higher the flexibility of the fabric, which was evaluated to be comfortable to wear. The 99.9% antibacterial properties of hemp products were considered to contribute to maintaining the health of modern people. Owing to its high intensity and high air permeability, it is considered highly usable in the production of children's clothing with a lot of activity. It was evaluated as an advantage that the disadvantage of hemp, which was limited as a material for summer clothing, was broadened to use for all seasons due to the fusion of Hanji. Otherwise, low consumer satisfaction as an outdoor wear is a disadvantage because hemp products had low elasticity and wrinkles.

• Journal of Hydrogen and New Energy
• /
• v.35 no.1
• /
• pp.97-104
• /
• 2024

In this study, combustion experiments were conducted to assess engine performance and exhaust gas characteristics using four blends of 1-pentanol and diesel as fuel in a naturally aspirated 4-stroke diesel engine. The blending ratios of 1-pentanol were 5, 10, 15, and 20% by volume. The experiments were carried out under four different engine torque conditions (6, 8, 10, and 12 Nm) while maintaining a constant engine speed of 2,000 rpm for all fuel types. The results showed that the use of 1-pentanol/diesel blended fuel generally led to a decrease in brake thermal efficiency, attributed to the low calorific value of the blend and the cooling effect due to the latent heat of vaporization. Additionally, both brake specific energy consumption and brake specific fuel consumption increased. However, the use of the blended fuel resulted in a general decrease in NOx concentration, a decrease in CO concentration except some conditions, and a reduction in smoke opacity across all conditions.

• Nuclear Engineering and Technology
• /
• v.56 no.2
• /
• pp.477-484
• /
• 2024

Experimental investigations on gamma - rays attenuation parameters and dielectric spectroscopic properties were done on a polymeric mixture with chemical composition (100-x) polyethylene + x basalt, where x = 0, 1, 3, 5, 10, and 20 wt%. Using the melting blending technique,six nanocomposite polymeric samples were prepared. The linear attenuation coefficient µ of each prepared set of samples was measured using a gamma-ray spectrometer including High Purity Germanium detector (HPGe) at energies 662.5, 1173.24, and 1332.51 keV. Based on the measured values of (µ) and sample density, the other effective shielding parameters were calculated. The values of µ showed an increase with increasing the dopant ratios from 0.0 up to 20.0 wt%. In addition, the µ values decreased with the photon's energy. The µ values were found 0.0847 up to 0.1175 cm^-1, 0.0571 up to 0.0855 cm^-1, and 0.0543 up to 0.075 cm^-1 at 662.5, 1173.24, and 1332.51 keV. for B0 up to B20, respectively. The ATR spectroscopy was done on the prepared samples, and a good evidence of adding the filler to the pure polyethylene (HDPE) was obtained. Besides, an enhancement in dielectric constant by insertion of basalt NPs also recorded and can be attributed to the large dielectric constant of basalt compared to pure HDPE.

• Korean Journal of Food Science and Technology
• /
• v.37 no.3
• /
• pp.405-411
• /
• 2005

Chitosan, second largest biomass after cellulose on earth, has potential for use as functional food package due to its antibacterial activity. However, due to high melting temperature of chitosan, chitosan films have been made by casting method. Because gelatin has relatively low molting temperature depending upon amount of plasticizer added, it was added to chitosan to produce commercially feasible film. The objective of the current study was to determine optimum blend ratio and amount of chitosan/gelatin blend solutions against antibacterial activities for extruder resin. Gram-positive bacteria (Bacillus cereus ATCC 14579 and Listeria monocytogenes ATCC 15313) and -negative bacteria (Escherichia coli ATCC 25922 and Salmonella enteritidis IFO 3313) were used. Paper (8 mm) diffusion and optical density methods were used to evaluate effect of different blending ratio solutions on the inhibition of bacterial growth. Measured clear none size ranged from 8 mm to 18.07 mm in paper diffusion test. For B. cereus, E. coli, and S. enteritidis, addition of $50\;{\mu}L$ blend solution (chitosan/gelatin = 2/8: 0.3 mg) resulted in clear zone on paper disc. In L. monocytogenes, inhibition effect was observed with 0.6 mg chitosan (chitosan/gelatin=4/6). Minimum inhibitory concentration (MIC) values of B. cerues, L. monocytogenes, E. coli, and S. enteritidis with addition of chitosan were 0.1461, 0.2419, 0.0980, and 0.0490 mg/mL, respectively, These results indicate possibility of producing commercially feasible film with addition of optimum chitosan/gelatin amount.

• Asian Journal of Turfgrass Science
• /
• v.24 no.2
• /
• pp.205-210
• /
• 2010

This study was conducted to investigate the effect of the mixed ratio of the soil amendments, peat, humate, peatmoss and zeolite, on the soil physicochemical properties. The mixed ratios of soil amendments were 0%, 3%, 5%, 7% and 10% (v/v) incorporated with sand which met to the USGA (United State of Golf Association) recommendation. It was measured pH, EC and CEC as a chemical properties. Porosity, capillary porosity, air-filled porosity, bulk density and hydraulic conductivity were also measured to analyze the changes of physical properties. Chemical properties were significantly different by mixture ratios of peat, humate, peatmoss and zeolite. When the results were applied to the USGA standard of the soil physical properties, the optimum mixture ratios of peat, humate and peatmoss were 5%, 3% and 7%, respectively. Air-filled porosity was factor involved in soil physical properties by blending with soil amendments and it was affected on volume of porosity and hydraulic conductivity. To analyze the corelation of mixture ratio versus to physical characters, the ratio of peat and peatmoss was significantly related to capillary porosity and hydraulic conductivity (P<0.05), that of humate hydraulic conductivity (P<0.01), and that of zeolite air-filled porosity and volume of porosity (P<0.05). These results could be used as a basic data for construction USGA sand green.