• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2015년도 추계 학술논문 발표대회
• /
• pp.32-33
• /
• 2015

Depending on the industrialization, construction market has grown buildings are based on concrete will continue to increase. But the problems of environmental pollution come to the fore with the indiscriminate use of concrete and rapid development. In addition, carbon dioxide(CO₂) in the process of producing cement being emitted a large amount of has been caused a serious problem of environmental pollution. This trend is being actively conducted research to reduce the use of cement. In this study, eco-friendly materials, such as flats, Blast-furnace slag by mix and cement review the mechanical characteristics of the mudflats eco-friendly cement mortar to reduce the usability of the review were seen as a green building material.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1995년도 봄 학술발표회 논문집
• /
• pp.72-77
• /
• 1995

Blast-furnace slag cement has been used widely as a structural material due to the latent hydraulicity of granulated ground blast furnace slag(GGBS)for a long time as The wall as ordinary portland cement. In this study, based on the fundamental investigation on the high strength and high durable concrete using the high fineness GGBS the following remarks can be made. 1) The average desired strenth of concrete is Or=600~800kg/$\textrm{cm}^2$. 2) The above high strength concrete using the high fineness GGBS is more workable than those using only OPC. 3) The adiabatic temperature and drying shringkage decrease, so the density and resistance to sea water attack increase as results. 4)The unit cement content and unit air entrained admixture at the same desired strength of concrete decrease, so the economical high strength concrete can be manufactured from using the high fineness GGBS.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2017년도 추계 학술논문 발표대회
• /
• pp.161-162
• /
• 2017

As the use of cement increases with the development of modern society along with the increase of buildings, environmental pollution intensifies and researches on industrial byproducts are continuing. Research on blast furnace slag and fly ash as industrial byproducts is increasing, and research on industrial byproducts such as polysilicon sludge and paper ash used in this study is increasing. Blast furnace slag, which is one of the industrial byproducts, has been widely studied as a material used with cement. However, in this study, we fabricated lightweight matrix of polysilicon sludge and paper ash replaced based on blast furnace slag, and performed SEM analysis.

• 기술사
• /
• 제33권4호
• /
• pp.77-83
• /
• 2000

In this study, engineering characteristics of permeable mortar using water-quenched blast furnace slag as fine aggregates were analyzed by laboratory experiments to examine its suitability for permeable concrete pavement techniques. Engineering characteristics of mortar were investigated by performing both the compressive, flexural strength tests together with the constant head permeability tests for twenty-six types of mixing samples having different percetage of slag, cement and water. After 28days of curing, every performance was tested to find optimum mixture. When the go coefficient of permeability was 10$\^$-2/cm / sec and flexural strength was 30kg/㎠, we conclusion that the best mix design in permeable mortar was made in the condition,60% of cement and 20% of water percentage of unit slag contents. From the present investigations, it is concluded that suitability for permeable concrete pavement techniques using water-quenched blast furnace slag as fine aggregates may possibly be used to achieve effects on strength together with drainage effects.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2018년도 추계 학술논문 발표대회
• /
• pp.83-84
• /
• 2018

As the concentration of greenhouse gases in the atmosphere increases, the reduction of CO2 is gaining worldwide attention. In the construction industry, cement replacement materials such as fly ash and blast furnace slag were investigated to reduce CO2 emissions in cement production process. Precast concrete is used in the field after manufacturing in the factory in the form of pipes and bricks because of shortening construction period and cutting construction cost. According to the results of previous research, it is known that early CO2 curing in concrete using OPC or fly ash has an initial strength enhancement effect and can be used for precast concrete production. Therefore, the purpose of this study is to evaluate the strength improvement effect by confirming the initial strength improvement effect when blast furnace slag is mixed.

• 한국건설순환자원학회논문집
• /
• 제5권1호
• /
• pp.8-13
• /
• 2017

본 연구는 $CO_2$를 다량 발생시키는 시멘트의 사용량을 줄이기 위한 일련의 연구로서, 산업부산물인 고로슬래그 미분말을 다량 치환하고 기존 알칼리 자극제를 대체하여 전기분해한 알칼리 수용액을 사용한 하이볼륨 시멘트 경화체의 개발을 위한 기초적인 연구를 수행하였다. 즉, 일반적인 시멘트를 사용한 시험체와 고로슬래그 미분말 40%, 60%에 일반적인 물과 전기분해 알칼리 수용액을 사용한 시험체에 대하여 압축강도, XRD 및 SEM을 측정하였다. 그 결과, 고로슬래그 미분말을 사용하는 경화체에 있어서 알칼리 수용액을 사용할 시 강도가 증가하고 입자 표면에 수화물이 다량 생성되는 결과를 얻었다. 특히, 고로슬래그 미분말을 40% 치환하고 알칼리 수용액을 사용한 경우, 일반적인 시멘트 경화체 보다 높은 압축강도를 발현하였다. 그러나 본 연구는 재령 10일에 한정하여 실시한 연구로서, 고로슬래그 및 전기분해 알칼리 수용액을 사용한 시험체에 대한 추가적인 연구가 필요하다고 판단된다.

• 한국건축시공학회지
• /
• 제13권1호
• /
• pp.29-37
• /
• 2013

In this study, a zero-cement brick is manufactured by replacing cement with recycled aggregates and blast furnace slag powder. Experimental tests were conducted with standard sized samples of $190{\times}57{\times}90mm$ (KS F 4004), and this manufacturing technique was simulated in practice. Results showed that the zero-cement brick with 0.35 W/B had the highest compressive strength, but the lowest absorption ratio. This absorption ratio of zero-cement brick with 0.35 W/B was lower than the required level determined by KS F 4004. Hence, to increase the absorption ratio, crushed fine aggregate (CA) and emulsified waste vegetable oil (EWO) were used in combination in the zero-cement brick. It was found that the zero-cement brick with CA of 20% and EWO of 1% had the optimum combination, in terms of having the optimum strength development (12 MPa) and the optimum absorption ratio (8.4%) that satisfies the level required by KS. In addition, it is demonstrated that for the manufacturing of zero-cement brick of 1000, this technique reduces the manufacturing cost by 5% compared with conventional cement brick.

• Geomechanics and Engineering
• /
• 제29권3호
• /
• pp.237-247
• /
• 2022

To investigate the curing temperature effect on the engineering properties of ground granulated blast furnace slag-cement bentonite (GGBS-CB) slurry for cutoff walls, the laboratory experiments including the setting time, unconfined compressive strength, and permeability tests were carried out. The mixing procedure for GGBS-CB slurry was as follows: (1) montmorillonite-based bentonite slurry was first fabricated and hydrated for four hours, and (2) cement or GGBS with cement was added to the bentonite slurry. The dosage range of GGBS was from 0 to 90 % of cement by mass fraction. The GGBS-CB slurry specimens were cured and stored in environmental chamber at temperature of 14±1, 21±1, 28±1℃ and humidity of 95±2% until target days. The highest average temperature of three seasons in South Korea was selected and used for the tests. The experimental results indicated that in early age (less than 28 days) of curing the engineering properties of GGBS-CB slurry were primarily affected by the curing temperature, whereas the replacement ratio of GGBS became a main factor to determine the properties of the slurry as the curing time increased.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 봄 학술발표회 논문집
• /
• pp.124-128
• /
• 1997

In order tohave a betterunderstanding of thefavorable effect ofground granulated blast-furnace slag and fly ash, slump loss, temperature risingand compressive strength of concrete were investigated into diffrent conditions. When slag was mixed with ordinary portland cement as30%, slump loss gotto some 18% at 60min, maximum temperatureto some $43^{\cire}C$ at 180min, compressive strength similar to that of ordinary portland concrete at 28 days. Therefore it wasnoted thatslump loss andmaximum teaperaturerising of concrete were very reduced according to ground granulated blast-furnace slag and fly ash mixed with ordinary portland cement.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 추계 학술논문 발표대회
• /
• pp.251-252
• /
• 2011

This study is to investigate experimentally the strength properties of mortar using recycled fine aggregates(RA) and blast furnace slag powder(BS) without cement according to type of fine aggregate. In the results of the study, compressive strength of RA was the highest. It can be considered that the results are due to the reaction of the non-hydration cement in RA to the latent hydraulicity reaction of the BS.