• International Journal of Aeronautical and Space Sciences
• /
• v.7 no.1
• /
• pp.54-64
• /
• 2006

To augment weakly damped lag mode stability of a hingeless helicopter rotor blade in hover, piezoelectric shunt with a resistor and an inductor circuits for passive damping has been studied. A shunted piezoceramics bonded to a flexure of rotor blade converts mechanical strain energy to electrical charge energy which is dissipated through the resistor in the R-L series shunt circuit. Because the fundamental lag mode frequency of a soft-in-plane hingeless helicopter rotor blade is generally about 0.7/rev, the design frequency of the blade system with flexure sets to be so. Experimentally, the measured lag mode frequency is 0.7227/rev under the short circuit condition. Therefore the suppression mode of this passive damping vibration absorber is adjusted to 0.7227/rev. As a result of damping enhancement using passive control, the passive damper which consists of a piezoelectric material and shunt circuits has a stabilizing effect on inherently weakly damped lag mode of the rotor blades, at the optimum tuning and resistor condition.

• The KSFM Journal of Fluid Machinery
• /
• v.2 no.1 s.2
• /
• pp.15-21
• /
• 1999

Some sized centrifugal compressors were designed and their performance measured to investigate the effects of exit blade thickness, width and back swept angle. The impeller of larger blade thickness shows low pressure ratio compared with that of smaller ones. Backswept angle also have a large effect on the efficiency. Measured values of slip factor are quite different from the estimated values of the Wiesner-Busemann model and an increase in the flow late.

• International Journal of Fluid Machinery and Systems
• /
• v.8 no.4
• /
• pp.311-317
• /
• 2015

It is difficulty to calculate velocity circulation in centrifugal pump impeller outlet accurately. Velocity circulations of a double-blade pump impeller outlet were calculated with Stodola formula, Weisner formula and Stechkin formula. Simultaneously, the internal flow of impeller for the double-blade pump were measured with PIV technology and average velocity circulations at the 0.8, 1.0 and 1.2 times of design flow were obtained. All the experimental values were compared with the above calculation values at the three conditions. The results show that calculation values of velocity circulations with Weisner formula is close to the experimental values. On the basis of the above, velocity circulations of impeller outlet were corrected. The results of experimental verification show that the corrected calculation errors, whose maximum error is 3.65%, are greatly reduced than the uncorrected calculation errors. The research results could provide good references for establishment of theoretical head and multi-condition hydraulic optimization of double-blade pumps.

• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.2
• /
• pp.109-116
• /
• 2001

The paper presents a speed control algorithm for a full pitch-controlled wind turbine system. Torque of a blade generated by wind energy is a nonlinear function of wind speed, angular velocity, and pitch angle of the blade. The design of the controller, in general, is performed by linearizing the torque in the vicinity of the operating point assuming the angular velocity of the blade is constant. For speed control, however the angular velocity is on longer a constant, so that linearization of the torque in terms of wind speed and pitch angle is impossible. In this study, a reference pitch model is derived in terms of a wind speed, angular velocity, and pitch angle, which makes it possible to design a controller without linearizing the nonlinear torque model of the blade. This paper also suggests a method of designing a hydraulic control system for changing the pitch angle of the blade.

• Aerospace Engineering and Technology
• /
• v.10 no.2
• /
• pp.74-81
• /
• 2011

A numerical simulation is performed to study the ground effect of a rotating rotor blade on a whirl tower using unstructured overset mesh. The aerodynamic change of the rotor blade by the structure around the whirl tower is also considered. The calculated results showed good agreement with the experiment for the hover performance. The ground effect of the rotor blade is investigated by comparing with the calculated results for the out of ground condition and the results of an analytic model.

• Aerospace Engineering and Technology
• /
• v.10 no.2
• /
• pp.11-19
• /
• 2011

A localization development of Composite rotor blade for Smart Unmanned Aerial Vehicle(SUAV) has been conducted. Overall localization development encompassed selection of domestic composite material having similar properties to that of original one at its best, coupon tests for data base of new material properties, re-calculation of blade sectional properties, and validation of structural/dynamic design requirements such as isolation of rotor natural frequency from excitation, static and fatigue strength, aeroelastic stability. The results of all these activities are described. This paper briefly discusses the improved manufacturing process for the localization of SUAV blade.

• Solar Energy
• /
• v.6 no.2
• /
• pp.86-92
• /
• 1986

This paper presents the aerodynamic performances of horizontal axis wind turbines with non-twisted but taperd blades. Five configurations of blades, namely, one straight blade and four tapered blades with taper ratio of ranging from 0.1 to 0.7 have been simulated. The aerodynamic performances of the wind turbines have been determined over blade incidence angle of ranging from $2^{\circ}$ to $6^{\circ}$ and keeping same solidity and radius of them. The results are presented comparing straight blade from four tapered blades for maximum power coefficient and tip looses against variation of taper ratio. It also shows that the wind turbine with taper ratio of 0.5 has the highest maximum power coefficient than others. And wind turbines with taper ratio below 0.2 have lower values of maximum power coefficients than straight one. The tip loss of straight blade is the largest and reduces Slightly with the decrementation of taper ratio.

• 유체기계공업학회:학술대회논문집
• /
• 1999.12a
• /
• pp.69-77
• /
• 1999

The aim of this paper is to understand the unsteady flow phenomena in a high speed centrifugal compressor channel diffuser. Instantaneous pressures are measured at six locations in the diffuser using fast-response pressure transducers. Instantaneous pressure ratio decomposition was applied to analyze the pressure signal. In vaneless space where impeller-vaned diffuser interaction is strong, aperiodic unsteadiness is high and periodic pressure waveforms by blade passing are not clear at low flow rates, especially near vane suction side. High aperiodic unsteadiness decreases downstream of diffuser. The blade-to-blade pressure wave does not disappear in surge flow condition. In surge there exist not only large scale periodic surge wave but also blade-to-blade pressure wave.

• 한국기계연구소 소보
• /
• s.13
• /
• pp.27-43
• /
• 1984

In order to obtain the high resilience, low compression set and less of hardness change in the wiper blade rubber, vulcanization system and receipes must be controlled. To improve the above the above Physical properties, the system should be taken as follows. i) peroxide vulcanization system and sulfur vulcanization system. ii) rubber having more cis-form than trans-form. iii) moderate particle size cabon black. v) usage of other improvement agent. The rubber blade with 4.4% compression set, 76% resilience, Hs 0 $\pm$ 2 hardness change could be abtained through vulcanization system, In addition, the surface of wiper blade must be treated by chemically and physically to minimize for the skid and friction.

• Journal of Korea Foundry Society
• /
• v.35 no.3
• /
• pp.62-66
• /
• 2015

Tape casting is an important forming operation used to prepare flat sheets in the various industries. In this study, Doctor Blade tape casting of In-based low melting point alloy was carried out. The purpose of this investigation was to determine the possibility of applying the Doctor Blade tape casting process to the manufacture of low melting point alloy sheets that can be used as thermal fusible parts of battery safety systems. In-based molten alloy that has a melting point of $95^{\circ}C$ was produced; it's viscosity was measured at various temperatures. The molten alloy was used as a slip in the caster of the Doctor Blade tape casting system. The effects of the molten alloy temperatures and carrier speeds on the produced sheet shape were observed. For the casting conditions of 1.5 cm slip height, $120^{\circ}C$ slip temperature, 0.05 mm blade gap and 60 m/min. carrier speed, an In-based alloy thin tape well shaped with 0.16 mm uniform thickness was continuously produced.