• Design & Manufacturing
• /
• v.6 no.1
• /
• pp.84-89
• /
• 2012

Silicone is recently used for LED chip encapsulment due to its good thermal stability and optical transmittance. In order to predict residual stress which causes optical briefringence and mechanical warpage of silicone, finite element analysis was conducted for both curing and cooling process during silicone molding. For analysis of curing process, a cure kinetics model was derived based on the differential scanning calorimetry(DSC) test and applied to the material properties for finite element analysis. Finite element simulation result showed that the curing as well as the cooling process should be designed carefully so as to reduce the residual stress although the cooling process plays the bigger role than curing process in determining the final residual stress state. In addition, birefringence experiment was carried out in order to observe residual stress distribution. Experimental results showed that cooling-induced birefringence was larger than curing-induced birefringence.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.294-295
• /
• 2006

Field sequential liquid crystal display (FSLCD) has advantages such as a high transmittance due to no use of color filter and high color reproductivity because of LED backlight for a luminance source. However, to realize FSLCD response time of the LCD must be below 5ms. In this paper, we have chosen electrically controlled birefringence (ECB) mode for this application and studied film compensation to improve the operating voltage and viewing angle and to achieve a fast response time optimizing the condition of the discotic film and TAC film, operating voltage decreases to 5V, and viewing angle range is $160^{\circ}$ at horizontal and vertical direction, respectively and $120^{\circ}$ in diagonal direction. (contrast ratio > 10:1) and optimized cell exhibits a fast response time of 4ms in most grey levels.

• Composites Research
• /
• v.17 no.4
• /
• pp.32-39
• /
• 2004

Among many fiber optic sensors, FBG sensors are being studied more actively than any other sensor due to good multiplexing capabilities. Recently, the application fields of FBG sensors are mainly focused on the composite materials through embedding rather than attaching on the surface. However, there are many limitations on the embedding FBG sensors into composite materials because of the birefringence effects which is induced when FBG sensors are not embedded parallel to the reinforcing fiber. In this study, the fabrication method of FBG sensors with various grating length that are easy to fabricate with good multiplexing capabilities and more stable from the birefringence effects are investigated. The signal characteristics of the FBG sensors are also verified through the cure monitoring of 2 kinds of composite materials.

• Electrical & Electronic Materials
• /
• v.8 no.2
• /
• pp.190-195
• /
• 1995

Temperature dependences of the dielectric constant K(T), remanent polarization $P_{r}$, (T), effective birefringence overbar .DELTA.n(T), transmitted light intensity and quadratic electro optic coefficient R(T) of the two-stage sintered xBa(L $a_{1}$2/N $b_{1}$2/) $O_{3}$-(1-x)Pb(Z $r_{y}$ $Ti_{1-y}$) $O_{3}$(x=0.085, 0.09, 0.40.leq.y.leq.0.70) ceramics were investigated. Increasing the PbZr $O_{3}$ contents, the crystal structure of a specimen was changed from a tetragonal phase to a rhombohedral and cubic phase, and the phase transition was showed a diffuse phase transition(DPT) characteristics. In the compositions which located on the PE-FE phase boundary, the discrepancy was observed between the Curie temperature and temperature which a microscopic polarization and effective birefringence were disappeared.red.d.

• Polymer(Korea)
• /
• v.35 no.5
• /
• pp.493-498
• /
• 2011

Reactive mesogens were used to prepare photo-cured liquid crystal films in which orientations of liquid crystal molecules were preserved by crosslinked networks of cured reactive mesogens. The molecular orientations of liquid crystal mixtures of photo-reative mesogens and non-reactive nematic liquid crystals were studied and compared before and after curing reactions. The effects of temperature and the amount of the non-reactive nematic liquid crystal in the mixture on birefringence of the liquid crystal films were investigated. It was found that optical compensation films with different birefringence could be prepared by controlling the amount of the nematic liquid crystals in the reactive mesogen mixtures.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05a
• /
• pp.109-113
• /
• 2005

We have studied a field sequential liquid crystal display (FSLCD) with electrically controlled birefringence (ECB). The ECB mode exhibiting fast response time, high transmittance, low operating voltage and adequate viewing angle. The positive liquid crystal (LC) is better than negative LC on dielectric anisotropy, birefringence and rotational viscosity. Because $K_{11}$ value out of the elastic coefficient of LC is also larger than $K_{22}$ value, decay time of VA-ECB is advantage. However, the transmittance & response time reduced with decreasing the cell gap. This drawback can be overcome by using LC with high ${\Delta}n$ but VA-ECB is occured loss of light efficiency because the $\gamma$ value increased by high ${\Delta}n$ of LC. Consequently, the HA-ECB mode is one of strongest candidate for FSLCD application.

• Journal of Biomedical Engineering Research
• /
• v.26 no.1
• /
• pp.37-42
• /
• 2005

We construct and test the polarization-sensitive optical coherence tomography (PS-OCT) system for imaging porcine and human articular cartilages. PS-OCT is a new imaging technology that provides information regarding not only the tissue structures but tissue components that show birefringence such as collagen. In this study, we measure the cartilage thickness of the porcine joint and the phase retardation due to collagen birefringence. Also, we demonstrate that changes of the collagen fiber orientation could be detected by the PS-OCT system. Finally, differences between normal and damaged human articular cartilage are observed using the PS-OCT system, which is then compared with the regular histology pictures. As a result, the PS-OCT system is proven to be effective for diagnosis of the pathology related to the cartilage. In the future, this technology may be used for discrimination of the collagen types. When combined with endoscope technologies, the PS-OCT images may become a useful tool for in vivo tissue testing.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.11
• /
• pp.58-68
• /
• 1997

The residual stresses in injection-molded plastic parts can be divided into two, i.e., the flow-induced residual stress produced in flowing stage and the thermally-induced residual stress produced in cooling stage. Especially, the main source for the defect in the final parts, such as warpage, is known to be the thermally-induced stresses. For the freely quenched samples the structures of residual stresses and bire-fringence have been investigated by many researchers extensively. However, the boundary condition for free quenching was found to be improper to study actual injection molding process. In the present study a datailed structure of the residual stresses and birefringence produced under constrained quenching has been investigated experimentally. In constrained quenched samples a similar pattern but much less stress values than that for the freely quenched samples has been found in the case of the thickness of 1.0 mm. Howvere, in the case of the thickness of 4.0mm, totally different stress profile has been found experimentally. Suprisingly uniform birefringence throughout whole thickness has been found for all the cases of constrained quenching. Finally, to explain the mechanism to produce the final residual stresses and bire-fringence some preliminary numerical results including free volume theory have been introduced briefly.

• Proceedings of the Optical Society of Korea Conference
• /
• 1999.08a
• /
• pp.108-109
• /
• 1999

• Proceedings of the Optical Society of Korea Conference
• /
• 1996.09a
• /
• pp.52-52
• /
• 1996