• Journal of IKEEE
• /
• v.15 no.1
• /
• pp.57-63
• /
• 2011

This paper presents a tunable band pass filter (BPF) for multi bio-signal detection. The bandwidth can be controlled by the bias current of transconductance (gm), while conventional BPF exploited switchable capacitor array for band selection. With this design technique, the die area of proposed BPF reduced to at least one tenth the area of conventional design. The simulation results show the high cut-off frequency tuning range of from 100Hz to 1Khz. The circuit was implemented with a 0.18um CMOS standard technology. Total current consumption is 1uA at the supply voltage of 1V with sub-threshold design technique.

• Journal of the Korean Society of Costume
• /
• v.56 no.4 s.103
• /
• pp.48-64
• /
• 2006

The purpose of the study was to demonstrate how to recreate spencer jacket in the empire style in an attempt to apply this historic style to theatrical costumes and other high fashion items in modern times. The study was carried out through 2 steps. (1)Block patterns of spencer jacket of its basic design were developed through draping based on the design characteristics mentioned above. (2)Spencer jackets of three designs, which were the typical designs of each category have been made of velvet to find out more specific structural characteristics. The structural characteristics of Spencer jacket in draping were as follows: (1)Jacket length position was suitable 9cm below body's bust line and neckline should be enlarged front & side neck point 2cm, back neck point 1.5cm. (2)Cut out the front bodice after CF line moved 1cm outwards and bust dart amount should not exceed 2-3cm. Shoulder point moved inwards. (3)Side back grain line was parallel to princess line of the back bodice. Add 0.5cm ease to the under arm of the front and side bark bodice, it was good for the activity of arm. (4)Armhole line was trued as maintaining to across back width 14-15cm at least. Shoulder line was to connect from the point 2cm depart shoulder point along armhole line to point 2cm side neck point along neck line. (5)Sleeve length was suitable 70cm, cut out the bias direction to move forwards the grain line from shoulder point. Puff position was good from the 2cm depart shoulder point to shoulder line.

• Journal of the Korean Society of Costume
• /
• v.53 no.3
• /
• pp.137-154
• /
• 2003

The purpose of this study is firstly to survey the social and cultural background of 20th century and women's status, and to identify what the ideal body is like and what the elements of outer garment and underwear are and the techniques to incarnate the ideal beauty. Various papers are referenced for theoretical study and the elements and techniques of underwear are analyzed based on photographical materials. This paper concludes as follows. In 1910's, ideal beauty has changed to H-style. In other words, the outer garment has confined the lower part of the body with plain H-type Hobble silhouette to express plump bust, somewhat slim waist, and small hips, As the underwears, cylindrical corsets which fasten from under the bust down to lap, brassiere which are helpful for plump bust, and artificial busts were worn. In 1920's, outer garment were Straight box silhouette style which were cut as tubular without dart, and the underwears were corselets which have been tubular from the bust to hip and the tubular chemi-knickers. The former corsets which had been hard-boned and been fastened with strings have been replaced by the hook closure due to the development of elastic joining method. In 1930's, women pursued perfect body showing the line of bust, waist, and hip. In order to express elegant beauty of female of Slim and long silhouette, Doter and underwear have been cut with bias and gore, and soft and flexible materials were flowed along the body. World war II in 1940's has made the women as social. Ideal beauty has changed to Short straight box silhouette which no more shows body line. Outer and underwears were simple and Practical style. In 1950's, ideal beauty was well-matured, elegant Women which were represented by round shoulder, conical breast, tiny waist and round hip. Outer garment showed Hourglass silhouette representing the body-tight suits with round shoulder pad and the wide flare skirts. As the underwears, conical brassiere by top circular stitch were preferred for plump and bulged bust and tight corsets for tiny waist and magnificent petticoats were worn.

• Fashion & Textile Research Journal
• /
• v.16 no.3
• /
• pp.421-433
• /
• 2014

The aim of this study was to provide compression wear manufacture brands with information needed for product development. 8 tops and 7 bottoms from widely recognized compression wear manufacture brands were selected, and their product structural elements were analyzed, too. The results showed that most compression wear designs were applications of cutting lines designed considering muscle movements of the human body. The average number of cutting lines for patterns and designs were 14 for tops and 15 for bottoms. Different colored material was mainly used on the top for areas that require ventilation or high movement during sports for tops, and for areas that require muscle and joint support during sports for bottoms. The functionality of top materials were found to be stretch, muscle support, moisture absorption and high speed drying, warmth and ventilation for tops, in order of frequency, and stretch, muscle support, moisture absorption and high speed drying, and pressure for bottoms, in order of frequency. Tops were cut in the direction of the lengthwise grain, and bottoms were not only cut in the direction of the lengthwise grain, but also in the direction of the crosswise grain and bias for many products. Tops consisted of an average of 13 organically connected panels, and bottoms consisted of an average of 18 organically connected panels, which was analyzed to improve functionality. The average clothing surface area stretch rate was 85.7% for tops and 70.0% for bottoms, indicating that bottoms were designed to have higher strain rates compared to tops.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.10
• /
• pp.1159-1165
• /
• 2008

In this paper, a single-feed equilateral-triangular microstrip antenna with truncated corners is used for achieving diverse radiation polarization. The proposed antenna is excited by a microstrip line, which is place parallel to an oblique side of the equilateral-triangular patch. Depending on whether the three identically-sized comers of the triangular patch are cut or not, the equilateral-triangular microstrip antenna shows linear polarization(LP) or left-hand circular polarization(LHCP) or Tight-hand circular polarization(RHCP). Based on the equilateral-triangular microstrip antenna with truncated corners, a novel reconfigurable microstrip antenna with switchable polarization sense is also proposed. The proposed reconfigurable antenna has a simple structure, consisting of a corner-truncated triangular patch, a small triangular conductor, and a microstrip line. Using a biased PIN diode between the patch and the small triangular conductor, it can produce LP or RHCP according to bias voltages. From the measured results, low cross polarization level when operated in the linear state and good axial ratio in the circular state are observed.

• Journal of the Korean Vacuum Society
• /
• v.12 no.4
• /
• pp.239-250
• /
• 2003

The reliability degradation phenomena in the SiGe hetero-junction bipolar transistor (HBT) are investigated in this review. In the case of the SiGe HBT the decrease of the current gain, the degradation of the AC characteristics, and the offset voltage are frequently observed, which are attributed to the emitter-base reverse bias voltage stress, the transient enhanced diffusion, and the deterioration of the base-collector junction due to the fluctuation in fabrication process, respectively. The reverse-bias stress on the emitter-base junction causes the recombination current to rise, increasing the base current and degrading the current gain, because hot carriers formed by the high electric field at the junction periphery generate charged traps at the silicon-oxide interface and within the oxide region. Because of the enhanced diffusion of the dopants in the intrinsic base induced by the extrinsic base implantation, the shorter distance between the emitter-base junction and the extrinsic base than a critical measure leads to the reduction of the cut-off frequency ($f_t$) of the device. If the energy of the extrinsic base implantation is insufficient, the turn-on voltage of the collector-base junction becomes low, in the result, the offset voltage appears on the current-voltage curve.

• Journal of The Korean Astronomical Society
• /
• v.38 no.2
• /
• pp.179-182
• /
• 2005

We conducted an extremely wide field survey of z ${\~}$ 6 Lyman break galaxies (LBGs) to precisely derive their bright end surface density overcoming the bias due to cosmic variance. We selected out LBG candidates in the Subaru/ XMM-Newton Deep Survey Field (SXDS) over the total of ${\~}1.0\;deg^2$ sky area down to $z_{AB} = 26.0 ({\ge}3{\sigma},\;2'.0 aperture)$ using i' - z' > 1.5 color cut. This sample alone is likely to be contaminated by M/L/T dwarfs, low-z elliptical galaxies, and z ${\~}$ 6 quasars. To eliminate these interlopers, we estimated their numbers using an exponential disk star count model, catalogs of old ellipticals in the SXDS and other field, and a z${\~}$6 quasar luminosity function. The finally derived surface density of z ${\~}$ 6 LBGs was 165 $mag^{-1}\;deg^{-2}$ down to $z_{AB}$ = 26.0 and shows good agreement with previous results from the narrower field survey of HST GOODS.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.4
• /
• pp.178-184
• /
• 2005

In this paper, using diplexer structure and varactor diode controlled by reverse bias voltage for diplexer switch gives possibilities to improve isolation and current characteristics. 1 have newly designed switch with high isolation by application varactor diode corresponding to capacitor of diplexer. The low-pass filter for proposed tunable diplexer passes the microwave signal in the bandwidth for wireless cellular network systems and high-pass filter passes it in the bandwidth for wireless personal communication services (PCS) network systems. As the capacitance of the low-pass filter increases, the cut-off frequency can be moved to low frequency, so that the switch is on state in cellular bandwidth and off state in the PCS bandwidth, in contrast to, as the capacitance for attenuation characteristic of high-pass filter increases, it can be moved to high frequency, so that the switch is off state and on state in the cellular bandwidth. it is possible to improve isolation and current consumption characteristics by application diplexer design methods and varactor diode. 1 expect that the tunable diplexer circuit and design methods should be able to find applications on MMIC and low temperature copired ceramic (LTCC).

• ETRI Journal
• /
• v.38 no.2
• /
• pp.235-243
• /
• 2016

A low-noise readout integrated circuit (ROIC) for a microelectromechanical systems (MEMS) microphone is presented in this paper. A positive feedback signal amplification technique is applied at the front-end of the ROIC to minimize the effect of the output buffer noise. A feedback scheme in the source follower prevents degradation of the noise performance caused by both the noise of the input reference current and the noise of the power supply. A voltage booster adopts noise filters to cut out the noise of the sensor bias voltage. The prototype ROIC achieves an input referred noise (A-weighted) of -114.2 dBV over an audio bandwidth of 20 Hz to 20 kHz with a $136{\mu}A$ current consumption. The chip is occupied with an active area of $0.35mm^2$ and a chip area of $0.54mm^2$.

• The Research Journal of the Costume Culture
• /
• v.16 no.2
• /
• pp.249-262
• /
• 2008

The purpose of this study is to contemplate evening dress in contemporary fashion, thereby to analyze aesthetic characteristics of evening dress. For such purposes, this thesis first provides the historical survey of evening dresses, and to conduct a case study of survey of fashion photographs covering $pr{\hat{e}}t-{\acute{a}}t$-porter design products from 2000 to 2007 presented by Valentine. Based upon the historical survey, there are five representative styles in evening dress. Flapper chic looks could be characterized by frequent usage of sleeveless straight silhouette with long or mini hemlines, expressing sensuality, luxury, and ethnicity. Satin Siren looks were characterized by bias-cut, slim, long silhouette, expressing sensuality and luxury. Feminine Ideal looks were characterized by hourglass silhouette and decolltage with feminine details such as bow, pleats and frills, expressing historicism, luxury and sensuality. Freedom and fantasy looks were characterized by ethnic details or modern silhouette with transparent, printed materials, expressing ethnicity, sensuality, and luxury. Finally, postmodern glamourous looks were characterized by body-conscious silhouette with transparent, shiny, or stretch materials, expressing sensuality, experimentalism and luxury.