• Journal of the Earthquake Engineering Society of Korea
• /
• v.3 no.3
• /
• pp.1-8
• /
• 1999

The bridges for Korea High-Speed Railway(KHSR) under construction are supported with pot bearings on the middle pier and with pad bearings on the side piers, respectively. The dynamic analysis on these bridges due to trains with high speed, however, has been performed neglecting the effects of bearings. The objective of this study is investigation on the dynamic behavior of bridge supported by pad bearings. The effects of pad bearings with various flexibilities on the dynamic responses of bridges are studied. From the results of this study, the effects of elastomeric bearing on the dynamic responses of bridge(especially vertical accelerations) may cause undesirable behaviors.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.247-250
• /
• 2000

This paper presents the dynamic analysis and experiment for a shaft system supported by angular contact ball bearings. Among others, the dynamic characteristics of bearings are significantly affected by axial preload and radial load applied. This paper rigorously analyzes the dynamic characteristics of a shaft system with angular contact ball bearings subject of axial preload so as to result in eigenvalues as well as bearing stiffness characteristics. Experiments are also performed to identify natural frequencies and stiffness characteristics of bearings implemented. Comparison is made on the theoretical and experimental results.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2003.04a
• /
• pp.427-439
• /
• 2003

A previous study evaluated the seismic response of typical multi-span simply supported (MSSS) and multi-span continuous (MSC) steel-girder bridges in the central and southeastern United States. The results showed that the bridges were vulnerable to damage resulting from impact between decks, and large ductility demands on nonductile columns. Furthermore, fixed and expansion bearings were likely to fail during strong ground motion. In this paper, several retrofit measures to improve the seismic performance of typical multi-span simply supported and multi-span continuous steel girder bridges are evaluated, including the use of elastomeric bearings, lead-rubber bearings, and restrainer cables. It is determined that lead-rubber bearings are the most effective retrofit measure for reducing the seismic vulnerability of typical bridges. While isolation provided by elastomeric bearings limits the forces into the columns, the added flexibility results in pounding between decks in the MSSS steel-girder bridge. Restrainer cables, which are becoming a common retrofit measure, are only moderately effective in reducing the seismic vulnerability of MSSS and MSC steel girder bridges.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1993.12a
• /
• pp.77-84
• /
• 1993

Systems with journal bearings generally operate in large scale and under severe loading conditions such as steam generator turbines and internal combustion engines, in contrast to the machineries using rolling element bearings. Failure of the bearings in these machineries can result in the system breakdown. To avoid the time consuming repair and considerable economic loss, the detection of incipient failure in journal bearings becomes very important. In this experimental approach, acoustic emission monitoring is employed to the detection of incipient failure caused by intervention of foreign particles most probable in the journal bearing systems. It has been known that the intervention of foreign materials, insufficient lubrication and misassembly etc. are principal factors to cause bearing failure and distress. The experiment was conducted under such designed conditions as inserting alumina particles to the lubrication layer in the simulated journal bearing system. The results showed that acoustic emission could be an effective tool to detect the incipient failure in journal bearings.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.3
• /
• pp.355-362
• /
• 2015

Test procedure for the design verification of wind turbine pitch and yaw bearings has been developed. Test items were selected to evaluate operational reliability of pitch and yaw bearings by considering loading and operational conditions, and by analyzing the design criteria of pitch and yaw bearings. The developed test items consisted of preliminary test, fatigue load test, extreme load test, low temperature environmental test and dismantling inspection after all the test were completed. Because it reflects the actual operational conditions of the pitch and yaw bearings, the developed test procedure has high reliability and can verify the basic design considerations in the international standard and guidelines.

• Tribology and Lubricants
• /
• v.33 no.5
• /
• pp.187-201
• /
• 2017

This paper presents the impact of couple stress lubricant on performance of slot-entry hydrostatic/hybrid journal symmetric/asymmetric bearings. Reynolds Equation using Finite Element Technique has been solved for the flow of couple stress and Newtonian lubricants in bearings. The results have been computed for concentric design pressure ratio(${\beta}^{\ast}=0.5$), slot width ratio (SWR = 0.25) and chosen parameters of couple stress lubricant ${\bar{l}}=5$, 10, 15. It is observed that numerically simulated outcomes for slot-entry journal bearings, considering the influence of couple stress lubricant indicate a substantial improvement in the performance of the bearing.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.4
• /
• pp.608-613
• /
• 2003

In this paper, the effect of interconnected boundary between journal and thrust bearings on the performance of self-acting air-lubricated bearings is investigated. When journal and thrust bearings have common boundary, conventional boundary condition which assumes that the boundary pressure is equal to atmosphere is no more valid. Instead, new boundary condition by mass conservation at interconnected boundary is needed. To do this, a duct model satisfying mass conservation at interconnected boundary is developed. Using this model, pressure distribution at interconnected boundary is numerically analyzed with changing the volume of interconnecting part. As a result, it is shown that load capacity of thrust bearing can be greatly increased when journal and thrust have a common boundary.

• Tribology and Lubricants
• /
• v.18 no.5
• /
• pp.364-370
• /
• 2002

In this paper, numerical analyses were undertaken to calculate the static and dynamic performances of step-pocket, inward pumping spiral grooved, outward pumping spiral grooved and herringbone grooved bearings. For each bearing, optimal values for various design parameters were obtained to maximize the load capacity and the stiffness and bearing performances were calculated. The optimized performances of these bearings were compared to conclude that the performance of step-pocket bearing is better than the other bearings.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.94-99
• /
• 2003

As the rotating speed of rotors is increased, the instability and power loss become serious problems. Gas bearings are introduced as a good solution to those problems. But in the development of gas bearings, high load capacity and high damping force to vibrations are required. In this study a new air bearing using leaf spring pad is introduced to improve load capacity and damping force. The experimental results of the leaf spring pad air bearings show high load capacity and high damping forces. And the results show that leaf spring pad air bearings can be simultaneously acted as radial and thrust bearings

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 1999.04a
• /
• pp.161-168
• /
• 1999

The concept of seismic design was induced in our country which was poor in it for the scarcity of recognition and insufficiency of funds. Recently many specialists are enforcing the provisions of seismic design. But because seismic force of seismic design is very great and all the seismic force are concentrated on the fixed bearings and substructure the bearings are the seismic force are concentrated on the fixed bearings and substructure the bearings are destroyed so that seismic design lose its basic concept. In addition when the earthquake which exceeds seismic design force takes place the bridge is collapsed. For these reasons the developed seismic isolation design concept was appeared which diminishes seismic force itself by period shift and additional damping distributes it to each superstructures evenly. Therefore this study introduced the method which combines PC-LEADeR(design program for L.R.B) with SAP 2000(linear elastic analysis) and performs the seismic isolation design more elaborately and simply verified the propriety of that method and examined the force control of L. R. B.