• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.879-884
• /
• 2007

Flywheel energy storage systems have advantages over other types of energy storage devices in such aspects as unlimited charge/discharge cycles and environmental friendliness. In this paper we propose a millimeter scale flywheel energy storage device. The flywheel is supported by a pair of passive magnetic bearings and rotated by a toroidally wound electric motor/generator. The geometry of the bearings is optimized for the maximum dynamic performance.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.799-802
• /
• 1995

Whale helical gears is used to transmit motion between parallel shafts, the shaft bearings are subjected to both radial and thrust loads. The reliability and life analysis are based on the two-parameter Weibull disribution lives of the component gears and bearings. Two methods of estimating the time between gear system overhauls and the number of replacement components needed were presented. The first method assumes replacement of all components during an overhaul of a failed gear system. the second method assumes replacement of failed comonents only. Renewal theory was presented to estimate the number of comonent replacements in a gear system for both methods.

• Tribology and Lubricants
• /
• 제14권3호
• /
• pp.65-73
• /
• 1998

A dynamic analysis and friction loss of non-variable swash plate compressor are studied theoretically. Rotating swash plate and reciprocating pistons are modelled kinematically, and forces and torques acting on rotor-bearing system are analyzed. Then, friction losses on 4 roller bearings, 10 sliding parts between swash plate and shoes, and 10 lubricating surfaces between cylinders and pistons are calculated. On each frictional element of sliding surfaces and roller bearings, the same friction loss is obtained, respectively.

• Tribology and Lubricants
• /
• 제12권1호
• /
• pp.47-55
• /
• 1996

In this study, steady state and perturbed pressures are experimentally measured under inherently compensated restrictors in externally pressurized air bearings. A piezo actuator is used for simulating small displacement perturbation in the air film. The pressures under the restrictors are measured by a miniature type pressure transducer and the height of the air film is measured by capacitance type gap sensors developed by Chapman's method. The perturbed pressure is obtained through Fourier transformation of the two signals. The measured perturbed pressures are in good agreement with the calculated values.

• Tribology and Lubricants
• /
• 제7권2호
• /
• pp.51-60
• /
• 1991

For the accurate run-out of a light rotor shaft the sliding bearings supplied with externally pressurized air are effectively applied, and it is important to predict the static and dynamic characteristics of rotor-bearing system. In this study direct numerical method is applied to solve the perturbed Reynolds' equation. To solve it the perturbed dimensionless mass flow rate is used as the boundary condition under the inherently-compensated restrictor. The dynamic characteristics of a rotor supported in the externally pressurized air bearings are analyzed, and as a result the orbit of the journal center is calculated. The theoretical results are investigated and discussed.

• Tribology and Lubricants
• /
• 제3권1호
• /
• pp.39-46
• /
• 1987

Frictional loss in turbulent regime is abnormally increased compared with in laminar regime. Thus the consideration of temperature rise across fluid film is significant in analysis and conventional isothermal theory loses its usefulness for performance prediction. This paper proposes to the three-dimensional thermohydrodynamic analysis of finite journal bearings operating under turbulent condition using two-equation model($\kappa-\varepsilon$ model) proposed by Hassid & Poreh. The equations are solved numerically by finite difference method. We make the analysis applicable even at large eccentricity when back flow of the lubricants occurs and axial flow is no longer ignored compared to circumferential flow.

• Journal of Mechanical Science and Technology
• /
• 제19권3호
• /
• pp.731-742
• /
• 2005

A magnetic bearing even with multiple coil failure can produce the same decoupled magnetic forces as those before failure if the remaining coil currents are properly redistributed. This fault-tolerant, force invariance control can be achieved with simply replacing the distribution matrix with the appropriate one shortly after coils fail, without modifying feedback control law. The distribution gain matrix that satisfies the necessary constraint conditions of decoupling linearized magnetic forces is determined with the Lagrange Multiplier optimization method.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1997년도 제25회 춘계학술대회
• /
• pp.190-197
• /
• 1997

The heat generation of angular contact ball bearings and deep groove ball bearings is studied with experiment and simulation. The temperature variation of inner, outer races and the temperature incresement distribution are measured by using thermocouples for the shaft speed, preload, viscosity of lubrucant and lubrication method. The measured values from experiment are used to estimate the heat generation rate. Oil-air lubrication using oils with different viscosities and grease lubrication are adopted.

• Tribology and Lubricants
• /
• 제11권1호
• /
• pp.44-49
• /
• 1995

Friction characteristic of an engine crankshaft bearing is affected by revolution speed, applied loads, and viscosity of lubrication. So, experimental investigation is required to observe the friction characteristics using these factors. Hydraulic cylinder, servo controller system which can be modified the applied load, and test rig for the observation of the characteristics of engine crankshaft bearings were designed and fabricated, and some experiments were performed. Friction torque, journal locus and circumferential temperature variation of crankshaft bearing were measured according to applied load, revolution speed, and oil inlet temperature.

• Tribology and Lubricants
• /
• 제9권1호
• /
• pp.22-31
• /
• 1993

The thermohydrodynamic performance of large tilting pad journal bearings is analyzed, taking into account the three dimensional variation of lubricant viscosity. The eddy viscosity model based on wall formula is applied. The effects of temperature rise and turbulence on the bearing performance are studied in comparision with the isothermal or the laminar analysis. It is shown that these effects have significant influence on temperature distribution, load capacity and power loss of the bearing.