• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.143-144
• /
• 2010

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.877-878
• /
• 2011

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.12
• /
• pp.1327-1333
• /
• 2013

Air bearings are widely used in precision stages because of low friction and high motion accuracy, however, they suffer from low stiffness in comparison with rolling bearings or hydrostatic bearings. So, several preloading methods using weight, magnet and vacuum force, and opposing pads have been used to increase the stiffness of the air bearings. In this paper, pressure distributions of the vacuum preloaded porous air bearings are calculated using the proposed method. And then, the load capacity and stiffness are analyzed. For the vacuum preloaded air bearings, the stiffness is increased owing to reduced bearing clearance by vacuum force. The simulation results indicate that variation of vacuum pressure with clearance in the vacuum pocket gives rise to low stiffness, so the vacuum pocket should be designed for pressure to be constantly maintained regardless of the bearing clearance by means of large effective pumping speed.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.4 s.181
• /
• pp.29-36
• /
• 2006

Micro drilling by high-speed air bearing spindle is very useful manufacturing technology in electronic industry For the design of high speed air bearing spindle, there are considered stability of air bearing spindle, allowable load of air bearing, run out and tooling system design for micro drill's attach and remove. According to suggested details, we designed and manufactured high-speed air bearing spindle and carried out performance estimation such as run out, temperature change in running air bearing spindle, stiffness, chucking torque. Results are follows; Run out was measured under $5{\mu}m$ at air bearing spindle revolution $20,000\sim125,000rpm$. High speed air bearing spindle's temperature rose about $20^{\circ}C$ after 5 minutes from running and then was fixed. Allowable thrust load of spindle was 17kgf. Chucking torque of collet was 15kgfcm.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.816-821
• /
• 2005

The cycloid reducer has very high efficiency, high ratios, high stiffness and small size, in comparison with a conventional gear mechanism, which makes it an attractive candidate for limited space and precision application such as industrial robot. There are several publications on analysis and design of the cycloid reducer, however, it was assumed that the contact stiffness of pin rollers and cycloid disk is constant regardless of their contact geometry. Moreover, the torsional stiffness of the cycloid reducer couldn't be calculated due to the assumption. In this paper, we present a new procedure of calculating torsional stiffness of the cycloid reducer using Hertz contact theory. First, conventional force analysis of the cycloid reducer is briefly reviewed. Then, iterative numerical calculation procedure of the contact stiffness is proposed based on the Hertz contact theory where the contact stiffness depends on the contact force. In addition, total torsional stiffness of the cycloid reducer is estimated considering its rolling element bearing stiffness. The torsional stiffness of the cycloid reducer is dominated by the rolling element bearing stiffness since the contact stiffness of the cycloid disk is too large.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.1
• /
• pp.10-17
• /
• 2009

Spindle design is very important for the improvement of the competitive power in production cost of high quality machine tools. The important factor in spindle design is not only to improve the natural frequency of spindle but also to reduce displacement of spindle end. In this paper, parameters those influence on static and dynamic stiffness of high-speed spindle have selected form preceding studies. And those selected parameters are applied to Taguchi Method. To perform FEM analysis, bearing conditions are selected with optimized condition. To know how to improve static and dynamic stiffness of machine tool spindle, natural frequency and displacement of spindle end are obtained by FEM analysis. The Taguchi Method was used to draw optimized condition of bearing position and it's stiffness. From these results, amplitude of vibration is enough good less than $3{\mu}m$ pk-pk of the spindle of 40,000rpm manufactured in this work by the optimal design.

• Tribology and Lubricants
• /
• v.20 no.4
• /
• pp.197-203
• /
• 2004

As the rotational speed and the track density are increased, the vibration of disk/spindle system becomes critical issue in order to reduce the track mis-registration. In this work, we propose a simple inclined air bearing (20${\times}$20 mm) system which is located very near to the rotating poly-carbonate disk, and investigate suppressing effect for the disk vibration mode (0,0) both experimentally and numerically. We find dynamic stiffness and damping coefficients of air bearing and then apply those values to the disk vibration analysis. Numerical results show about 10 percent difference comparing to the experimental results. Also we investigate the reduction of disk vibration and power consumption with two different kinds of inclined bearing for the normal disk drive system experimentally. We find inclined air bearing can reduce about 30 percents of the transverse disk vibration.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.1
• /
• pp.23-29
• /
• 2001

Cylindrical type of self-controlled restrictor are designed for hydrostatic bearing of grinding wheel spindle. Typical hydrostatic journal bearing with the designed restrictor is analytically model. According to the model, the affect of oper-ation parameters, such as, initial cross distance, supply pressure, diameter of two supply holes, pre-load of spring, and clearance between spindle and housing, on bearing stiffness are analyzed. From the results of the analysis, the optimum conditions of operation parameters that maximize the bearing stiffness are estimated.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.6
• /
• pp.767-772
• /
• 2011

The thermal deformation of machine tool spindle influences the performance of the manufacturing systems for precision products. According to previous studies, major factors that will affect the stiffness of the spindle include spindle diameter, elasticity of the material, bearing stiffness and bearing span. It is difficult to change spindle diameter or elasticity of the material. but change of bearing position is easy in the given range compared to other factors. In this paper, we will find a solution to minimize thermal deformation through Change the span of the bearing.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.4
• /
• pp.522-527
• /
• 2008

On designing of hydrostatic bearing, load, quantity of oil, stiffness and friction load are considered as basic characteristics. For the analysis of these basic characteristics, pressure distribution by oil film is obtained. Speed of piston, clearance, leakage of oil, eccentricity, shape and roughness of bearing affect the results which are the analysis of basic characteristics of load, quantity of oil, stiffness and friction load. The relationship among those factors are required for optimum designing of hydrostatic bearing for machining tool. Reynold's Equation is calculated through finite element method. Load, leakage of quantity and pressure distribution as variation of length, land length ratio, eccentricity and axial velocity of bearing are investigated. Then optimum design variables are obtained.