• Transactions on Electrical and Electronic Materials
• /
• 제3권3호
• /
• pp.1-7
• /
• 2002

The developed patterns by direct writing of electron beam are measured by AFM, FESEM and optical profiler of WYKO NT3300. From different measurement methods, the measured linewidths of the patterns are shown a little bit wider than designed pattern size due to electrons scattering effect during direct writing of electron beam. The optimized conditions of these experiments are suggested and explained for the forming of structures below 0.1 ㎛ dimension size. Because of electron scattering effects from the different under layers such as Si, Si$_3$N$_4$ and aluminum, the developed pattern size is also influenced by the accelerated energy of electrons, dose, resist and soft and hard bake conditions in PMMA. The distributions of electron beam and calculations of backscattering coefficient are demonstrated by Monte Carlo simulation. From the measured results, the developed linewidth of PMMA/Al /silicon is shown a little bit wider than that of PMMA/Si$_3$N$_4$/silicon structure due to the backscattering effects.

• 한국군사과학기술학회지
• /
• 제9권2호
• /
• pp.26-33
• /
• 2006

A sonar dome is basically designed and installed to protect sonar array from shocks, sea wave slaps and floating matters. The acoustic wave passing through sonar dome, however, can be distorted in magnitude and phase. This paper presents a numerical method for predicting the steady-state sound pressure on the surface of transducer array in the sonar dome and typical results of sonar beam pattern affected by sonar dome. A beam tracing model with phase information and a multi-layered elastic boundary model are involved. A full three-dimensional sonar dome is modeled as a GRP acoustic window, a rubber coated steel baffle and a rubber coated steel hull. A transducer array is modeled as thick steel cylinder. There are some assumptions such as incidence of plane wave, specular reflection on boundary and directionality of transducer element.

• 소음진동
• /
• 제10권1호
• /
• pp.123-128
• /
• 2000

This paper describes the optimization of the hexagonal array transducer using finite element method. The transducer consists of the disc type sensors. Three dimensional beam patterns of each element and the array transducer are analysed using the finite element code ATILA. Beam patterns were analyzed for the disc type transducer. To optimize beam patterns of the array transducer, Chebyshev polynomial weight is applied to each element. In case of applying optimized weight, a 30 degree width beam pattern is presented at 10kHz. This paper also includes the effect of rubber filling material instead of using the water inside the transducer array.

• The Journal of the Acoustical Society of Korea
• /
• 제25권1E호
• /
• pp.25-31
• /
• 2006

Two twin microphones may produce particular patterns of binaural directivity by time delays between the twin microphones. The boundary element method (BEM) was used for the simulation of the sound pressure field around the KEMAR head model in order to quantify the acoustic head effect. The sound pressure onto the microphone was calculated by the BEM to an incident sound pressure. Then a planar directivity pattern was formed by four sound pressure signals from four microphones. The optimal binaural directivity pattern may be achieved by adjusting time delays at each frequency while maintaining the forward beam pattern is relatively bigger than the backward beam pattern. The simulation results were verified by the experimental measurement.

• The Journal of the Acoustical Society of Korea
• /
• 제24권3E호
• /
• pp.115-122
• /
• 2005

Two twin microphones may produce particular patterns of binaural directivity by time delays between twin microphones. The boundary element method (BEM) was used for the simulation of the sound pressure field around the head model in order to quantify the acoustic head effect. The sound pressure onto the microphone was calculated by the BEM to an incident sound pressure. Then a planar directivity pattern was formed by four sound pressure signals from four microphones. The optimal binaural directivity pattern may be achieved by adjusting time delays at each frequency while maintaining the forward beam pattern is relatively bigger than the backward beam pattern.

• 전기전자학회논문지
• /
• 제24권2호
• /
• pp.626-631
• /
• 2020

본 논문에서는 컨포멀 어레이(Conformal Array) 빔 합성 기법에 관한 연구를 수행하였다. 일반적인 선형 배열에서의 빔 조향에 따른 성능 열화 없이 빔 조향을 수행할 수 있는 컨포멀 어레이는 다양한 레이다 시스템에 적용되고 있다. 평면형 선형 배열에서의 빔 합성 기법과 달리 컨포멀 배열은 곡면상에 복사소자가 위치하므로 복사소자별로 파면(Wave Front)까지의 위상을 보상해 주어야 한다. 또한 복사소자별 옵셋 각도(Offset Angle)를 계산하여 실제 q빔 합성 시 적용함으로서 정확한 빔 패턴을 예측할 수 있었다. 본 논문에서는 위상 보상 및 옵셋 각도를 계산하여 빔 패턴 합성 시 적용한 후 빔 패턴 비교를 수행하였으며, 수학적인 분석을 통해 성능을 비교하였다.

• 대한전자공학회논문지TC
• /
• 제40권10호
• /
• pp.150-158
• /
• 2003

라인 소스에 의한 빔 패턴 합성 문제에서 소스 분포함수와 빔 패턴간의 관계는 푸리에 변환쌍으로 표현 될 수 있다. 본 연구에서는 원하는 lobe형 빔 패턴을 만족시키는 라인 소스 분포함수를 반복 샘플링을 통한 비선형 역변환법을 사용하여 합성하는 일반적인 방법을 제안한다. 이 방법은 유전 매질에 TE 및 TM 평면파 입사시 원하는 역산란 반사계수를 갖도록 하는 연속적으로 분포된 유전율 합성에 적용될 수 있으며, 임의 반사계수를 갖는 전송선로 합성에도 적용될 수 있는 장점을 가진다. 대역저지 공간 필터 및 분산 특성을 갖는 전송선로 필터에 적용, 분석하므로서 제안한 방법의 타당성을 보인다.

• 한국정밀공학회지
• /
• 제15권10호
• /
• pp.156-164
• /
• 1998

Electronic Speckle Pattern Interferometry(ESPI) has been used to measure surface deformations of engineering components and materials in industrial areas. ESPI, a non-contact and non-destructive technique, is capable of providing full-field results with high spatial resolution and high speed. One of the important application using electronic speckle pattern interferometry is electronic speckle contouring of a diffused object for 3-D shape analysis and topography measurement. Generally the electronic speckle contouring is suitable for providing measurement range from millimeters to several centimeters. In this study, we introduce the contouring method by modified dual-beam speckle pattern interferometer and the shift of the two illumination beams through optical fiber in order to obtain the contour fringe patterns. We also describe formation process of depth contour fringes and grid contour fringes by shifting direction of the two illumination beams. Before the experiments, we performed the geometric analysis for dual-beam-shifted ESPI contouring, and then, the electronic speckle contouring experiment with various specimens. For quantitative analysis of the contour fringes, we used 4-frame phase shifting method with PZT Finally, good agreement between the geometric analysis and experimetal results is obtained.

• 한국ITS학회 논문지
• /
• 제3권1호
• /
• pp.21-30
• /
• 2004

본 논문에서는 자동요금 징수 시스템(ETCS : Electronic Toll Collection System)의 RSE와 OBU 간의 RF link설계와 도로의 폭과 진행 방향 길이에서 적절한 통신 영역을 얻기 위해 요구되는 안테나의 빔 패턴 특성을 분석하였다. 이 과정은 능동형 DSRC를 기반으로 하는 ITS 서비스의 시스템 요구 규격을 결정하기 앞서 수행되어져야 하며, ETCS 기지국 설계 및 구축에서 가장 기본적이고 중요한 기술적 분석을 위하여 고찰하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.263-266
• /
• 2002

An optical method for surface roughness estimation based on statistical analysis of the light intensity of a scattered laser beam pattern. The method is very simple but has a disadvantage that no more information than the averaged roughness is estimated. In this study a new try was conducted to derive more advanced surface information from the details of the light intensity distribution. Some periodic ripples among the light intensity distribution being assumed to relate with scratch left on the machined surface, a corresponding surface profile is estimated from the ripples using FFT and IFFT algorithm. IFFT technique is used to extract some dominant signal components among the intensity distribution. Compared to the measured profiles by a stylus type surf-tester, the profiles obtained through the proposed method are probably acceptable in a sense of the profile shape. Calibration of the amplitude needs more works in the future.