• ETRI Journal
• /
• v.27 no.1
• /
• pp.122-125
• /
• 2005

A polymer-based planar-lightwave-circuit-type variable optical attenuator (VOA) was fabricated using a hot embossing process. With an optimized one-step embossing process, forty micro-channels for the guidance of light were defined on a polymer thin film with an accuracy of ${\pm}0.5{\mu}m$. The fabricated polymeric thermo-optic VOA shows 30 dB attenuation with 110 mW electrical input power at $1.55{\mu}m$. The rise and fall times are less than 5 ms.

• BMB Reports
• /
• v.51 no.4
• /
• pp.167-173
• /
• 2018

Experimental results obtained from research using only one sex are sometimes extrapolated to both sexes without thorough justification. However, this might cause enormous economic loss and unintended fatalities. Between years 1997 and 2000, the US Food and Drug Administration suspended ten prescription drugs producing severe adverse effects on the market. Eight of the ten drugs caused greater health risks in women. Serious male biases in basic, preclinical, and clinical research were the main reason for the problem. This mini-review will describe why and how funding organizations such as the European Commission, the Canadian Institutes of Health Research, and the US National Institutes of Health have tried to influence researchers to integrate sex/gender not only in clinical research, but also in basic and preclinical research. Editorial policies of prominent journals for sex-specific reporting will also be introduced, and some considerations in integrating sex as a biological variable will be pointed out. To produce precise and reproducible results applicable for both men and women, sex should be considered as an important biological variable from basic and preclinical research.

• Progress in Superconductivity and Cryogenics
• /
• v.14 no.4
• /
• pp.46-49
• /
• 2012

The selection of the temperature sensor in the cryogenic system depends on the temperature range, shape and accuracy. The accuracy of the temperature sensor is essential to improve the reliability of experiment. We have developed the variable temperature cryostat using a two-stage cryocooler. In order to reduce heat load, thermal shield is installed at the first stage with MLI (Multiple layer insulation). We have also developed the sensor holder calibrating more than twenty sensors at the same time for saving time and money. The system can calibrate sensor at variable temperature by controlling electric heater. In this paper, we present design and fabrication of variable temperature cryostat and representative result of Cernox sensor calibration.

• Communications of the Korean Mathematical Society
• /
• v.37 no.1
• /
• pp.207-212
• /
• 2022

In this paper, an interesting integral involving the Ī-function of one variable introduced by Rathie has been derived. Since Ī-function is a very generalized function of one variable and includes as special cases many of the known functions appearing in the literature, a number of integrals can be obtained by reducing the Ī function of one variable to simpler special functions by suitably specializing the parameters. A few special cases of our main results are also discussed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.10 s.181
• /
• pp.2477-2486
• /
• 2000

A planetary gear assembly is a key component to combine and/or split a power from the source. With a planetary gear assembly, a continuously variable unit extends its capacity by means of power bra nching mechanism. Power branching with one planetary gear assembly and one continuously variable unit is categorized into 12 basic types. Each type represents peculiar power transmitting characteristics. Additionally, a multi-mode (range) continuously variable transmission can be designed with accompanying clutches. A multi-mode continuously variable transmission changes the path through which the source power is transmitted. Each path has its own features, such as high efficiency. In this paper, some design principles are examined such as, criteria to guarantee the minimum power efficiency, and constraints to guarantee the smooth mode shift after discussing well-known features of multi-mode M mathematically.

• Journal of the Korean Data and Information Science Society
• /
• v.7 no.2
• /
• pp.219-226
• /
• 1996

Basic objective in cluster analysis is to discover natural groupings of items or variables. In general, variable clustering was conducted based on some similarity measures between variables which have binary characteristics. We propose a variable clustering method when variables have more categories ordered in some sense. We also consider some measures of association as a similarity between variables. Numerical example is included.

• Proceedings of the Korean Society for Quality Management Conference
• /
• 2009.10a
• /
• pp.3-10
• /
• 2009

When the measurement method for a performance variable is destructive or expensive, it is profitable to replace the performance variable with a highly correlated surrogate variable. In this paper we propose screening procedures using a surrogate variable with specified producer's and consumer's risks. Blending the basic concepts of acceptance sampling plans and screening procedures, the proposed model can be used effectively by quality professionals. Two models are considered: the normal model with dichotomous performance and continuous surrogate variables, and the bivariate normal model with continuous performance and surrogate variables. It is assumed the surrogate variable given the performance variable is normally distributed in the normal model, and performance and surrogate variables are jointly normally distributed in the bivariate normal model. For the two models, Producer's and consumer's risks are derived, and methods of finding the optimal screening procedures are presented. Numerical examples are also given.

• Journal of Korean Society for Quality Management
• /
• v.37 no.4
• /
• pp.23-30
• /
• 2009

When the measurement method for a performance variable is destructive or expensive, it is profitable to replace the performance variable with a highly correlated surrogate variable. In this paper we propose screening procedures using a surrogate variable with specified producer's and consumer's risks. Blending the basic concepts of acceptance sampling plans and screening procedures, the proposed model can be used effectively by quality professionals. Two models are considered: the normal model with dichotomous performance and continuous surrogate variables, and the bivariate normal model with continuous performance and surrogate variables. It is assumed the surrogate variable given the performance variable is normally distributed in the normal model, and performance and surrogate variables are jointly normally distributed in the bivariate normal model. For the two models, producer's and consumer's risks are derived, and methods of finding the optimal screening procedures are presented. Numerical examples are also given.

• International journal of advanced smart convergence
• /
• v.11 no.1
• /
• pp.87-93
• /
• 2022

In each country, efforts are being made to replace engine-driven cars and motorcycles using fossil fuels with electric drive. Electrically driven vehicles have the advantage of no harmful gas or environmental pollution and low noise. In the motorcycle market, China accounts for more than 95% of the world, and the electric motorcycle market is being revitalized due to the strengthening of regulations. Japan is actively preparing to include electric motorcycles in ISO 26262, forming a TF team centered on electric motorcycle producers. Therefore, it is necessary to respond to standardization targeting China and Japan in Korea. In this study, we propose a proprietary transmission model that can be applied to small electric vehicles that can be operated in hilly domestic terrain. The proposed continuously variable transmission model is a continuously variable transmission system which moves the pin between the basic disk and the rotary disk using a spline to perform shifting. The proposed continuously variable transmission model is used in the pulley configuration by connecting the linear type spline and the inclined spline with the central axis of the basic disk and the rotational disk, respectively. In addition, it can be divided into two types according to the application of the auxiliary disk, and the production drawing is completed for the practical use of the model.

• Journal of the Korean housing association
• /
• v.26 no.4
• /
• pp.75-82
• /
• 2015

Although the government has revised the child welfare act, institutionalized the establishment of local children's centers, and given financial support for them, there are a number of problems with respect to their operation. Specifically, one of main problems is their limited space. Diverse problems that go with the arrangement of limited space and usability have occurred, however there are only a few strategies to use limited space flexibly. This study assumed variability as one of the methods to solve spatial problems. As a basic research for the assumption, Analyzing the variable method and characteristics of domestic and foreign child-care facility guidelines was performed trying to take advantage of as a basic data in order to seek a variable scheme of local children centers' indoor space. For this purpose, study analysed the methods and characteristics of variability centering on aspects related to variability which are environmental design elements required by local children's centers as suggested in previous studies. The results are as follows. First, the variability of space should be planned according to activity and time, and consider the methods of division, storage, and other facilities necessary. Second, methods of variability in space can be classified into creating areas and structures that are variable. Third, as a result of analysing the environmental design elements required by local children's centers, this study discovered the following characteristics: multi-purpose usability through a combination of variable devices, transition through a variable space medium and setting up areas and expansion of indoor variability assuming usability through internal and external connections.