• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.669-674
• /
• 2004

In this study, the analytical method to evaluate the response of rotor-bearing system subjected to base excitation was presented. The equations of motion contain speed dependent gyroscopic terms, base rotation dependent parametric terms and several forcing function terms which depend on linear accelerations, rotational accelerations and a combination of linear and rotational combination. The study of rotor-bearing system excited by its base motion is not only able to predict the rotational performance, but provides the fundamental data for vibration isolation. In order to illustrate transient response, transient response analysis of a practical application sample were performed. The transient response was carried out for the given base excitation by using the state-space Newmark method that incorporates the average velocity concept.

• The Journal of Advanced Prosthodontics
• /
• 제9권4호
• /
• pp.278-286
• /
• 2017

PURPOSE. The aim of this study was to determine the influence of long base lengths of a fixed partial denture (FPD) to rotational resistance with variation of vertical wall angulation. MATERIALS AND METHODS. Trigonometric calculations were done to determine the maximum wall angle needed to resist rotational displacement of an experimental-FPD model in 2-dimensional plane. The maximum wall angle calculation determines the greatest taper that resists rotation. Two different axes of rotation were used to test this model with five vertical abutment heights of 3-, 3.5-, 4-, 4.5-, and 5-mm. The two rotational axes were located on the mesial-side of the anterior abutment and the distal-side of the posterior abutment. Rotation of the FPD around the anterior axis was counter-clockwise, Posterior-Anterior (P-A) and clockwise, Anterior-Posterior (A-P) around the distal axis in the sagittal plane. RESULTS. Low levels of vertical wall taper, ${\leq}10-degrees$, were needed to resist rotational displacement in all wall height categories; 2-to-6-degrees is generally considered ideal, with 7-to-10-degrees as favorable to the long axis of the abutment. Rotation around both axes demonstrated that two axial walls of the FPD resisted rotational displacement in each direction. In addition, uneven abutment height combinations required the lowest wall angulations to achieve resistance in this study. CONCLUSION. The vertical height and angulation of FPD abutments, two rotational axes, and the long base lengths all play a role in FPD resistance form.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.129.1-129
• /
• 2001

In this paper, we present an approach for matching images from finding interesting points and applying new image interpolation algorithm. New algorithms are developed that automatically align the input images match them and reconstruct 3-D surfaces. The interpolation algorithm is designed to cope with simple shapes. The proposed image interpolation algorithm generate a rotation image about vertical axes by an any angle from 4 base images. Each base image that was obtained from CCD camera has an angle difference of 90$^{\circ}$ The proposed image interpolation algorithm use the geometric analysis of image and depth information.

• 전자공학회논문지S
• /
• 제34S권2호
• /
• pp.63-70
• /
• 1997

This paper proposes a new algorithm for recognizing polyhedral objects using a single 2-D image. It is base don a new representation scheme having two level hierarchey. In the lower level, geometrical features of each primitive surface are represented using their signatures and the variation of signature due to rotation is represented suing the rotation map. In the higher level, topological features are represented in the inter-surface description table(SDT). Based on the proposed representaton scheme, loer level database searched to find a matching primitive surface. The srotation map determines the degree of rotation as well as the matchness. If all surfaces in a test object find their matching primitive surfaces, its structural information is compared with the SDTs of object models. If primitive surfaces of a test object equal to tha tof certain model and satisfy inter-surfaces relationship in SDT, a test object is recognized as the model.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.115-120
• /
• 2001

A gyroscope is a rotating body possessing one axis of symmetry and whose rotation about the symmetry axis is relatively large compared with the rotation about any other axis. Tuning fork is this type of structure that various modem gyro-sensors are based on. In this paper, dynamic behavior of a cantilevered beam subjected ta a base rotation with respect to the eccentric axis that is parallel to the beam axis is analyzed. The final equations of motion in terms of generalized coordinates can be solved with numerical scheme with various values of angular velocities and angular accelerations of the rotating axis. In contrast to the case of rotating cantilever beam like helicopter blade, the rotational motion with respect to the beam axis has effect to decrease the stiffness of the beam and has unstable region depending on the magnitude of the rotational angular velocity and angular acceleration.

• 대한치과교정학회지
• /
• 제20권2호
• /
• pp.355-361
• /
• 1990

This study was undertaken to finish the design of the adequate preadjusted bracket in Korean. The labio-lingual & bucco-lingual width of tooth & in-and-out of the bracket base was studied in normal occlusion of 17 males & 17 females. The following results were obtained. 1. The in-and-outs of the bracket base in Korean were obtained (table 2). 2. The in-and-outs of the premolar & molar were no significant due to variation according to arch wire shape in clinical practice, so the more adjustment of arch wire was required. 3. The more amount of offset was required at lateral-canine offset than at central-lateral offset in 1st order bending, due to difference of the in-and-out. 4. The degrees of the anti-rotation in molar were obtained (table 3).

• Earthquakes and Structures
• /
• 제9권4호
• /
• pp.831-849
• /
• 2015

Seismic-design procedures for walls require that the confinement in the critical (plastic hinge) regions should extend over a length in the compression zone of the cross section at the wall base where concrete strains in the Ultimate Limit State (ULS) exceed the limit of 0.0035. In a performance-based framework, confinement is linked to required curvature ductility so that the drift demand at the performance point of the structure for the design earthquake may be met. However, performance of flexural walls in the recent earthquakes in Chile (2010) and Christchurch (2011) indicates that the actual compression strains in the critical regions of many structural walls were higher than estimated, being responsible for several of the reported failures by toe crushing. In this study, the method of estimating the confined region and magnitude of compression strain demands in slender walls are revisited. The objective is to account for a newly identified kinematic interaction between the normal strains that arise in the compression zone, and the lumped rotations that occur at the other end of the wall base due to penetration of bar tension yielding into the supporting anchorage. Design charts estimating the amount of yield penetration in terms of the resulting lumped rotation at the wall base are used to quantify the increased demands for compression strain in the critical section. The estimated strain increase may exceed by more than 30% the base value estimated from the existing design expressions, which explains the frequently reported occurrence of toe crushing even in well confined slender walls under high drift demands. Example cases are included in the presentation to illustrate the behavioral parametric trends and implications in seismic design of walls.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제34권2호
• /
• pp.133-139
• /
• 2012

모든 환자들은 구순접합술을 시행 받았고 구순 및 구개열 유아들은 악정형장치인 Latham을 사용하였다. 수술의 기술적 변화들은 앞서 설명하였다. Columella 부위의 높은 rotation과 releasing incision은 내측 입술 부위를 충분히 길게 해주고, advancement flap이 phitral column 상방으로 최소로 침범되게 하여 균형적인 입술을 만들 수 있다. 또한 구륜근을 외번시켜 philtral ridge를 형성하고, 작은 unilimb Z-plasty을 구순측 Cupid's bow handle 높이에 맞게 시행 후, vermilion-cutaneous junction에서부터 상방으로 cutaneous closure 시행한다. 변위된 alar cartilage는 nostril rim incision을 통해 동측 upper lateral cartilage에 매달며, Alar base는 anterior-caudal septum의 위치, sill의 설정 그리고 외측 vestibular web 제거를 포함하여 3차원적으로 설계하여 치료해야 한다. 이번에 소개한 Mulliken의 치료법이 환자들과 외과의사들에게 많은 도움이 되기를 바란다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 추계학술대회 논문집
• /
• pp.107-108
• /
• 2008

• 한국운동역학회지
• /
• 제16권1호
• /
• pp.81-88
• /
• 2006

Present study is to know the relation with throwing speed according to the uniform torque by the shoulder joint, over 20 persons of professional baseball, and were measured the uniform torque by the shoulder joint accordance with throwing speed between (A-low speed) and (B-high speed) of each group. In the present study, three components were measured, and analyzed with having an approximated output value appearing by changing angular velocity, and in $30^{\circ}/sec$, the maximum strength of muscles was measured, and in$210^{\circ}/sec$, the points of endurance strength of muscles were measured and analyzed, and the following result could be obtained. 1. In muscles strength (peak torque)of inner rotation, and outer rotation for respect to each speed of shoulder joint, though there did not appear outstanding difference between A group and B group in the $30^{\circ}/sec$, it showed that group B has priority in a little. Also in outer rotation by shoulder joint, though there appeared the same difference between A group and B group, B group is tended to be prior to A group in a little. 2 In the view of muscles strength (peak torque)of inner rotation, and outer rotation for respect to each speed of shoulder joint, though there did not appear outstanding difference between A group and B group in the $30^{\circ}/sec$, it showed that group B has priority in a little. Also in outer rotation by shoulder joint, though there appeared the same difference between A group and B group, B group is tended to be prior to A group in a little. 3. In the view of muscles strength(peak torque)of inner rotation, and outer rotation for respect to each speed of shoulder joint, though there did not appear outstanding difference between A group and B group in the $30^{\circ}/sec$, it showed that B group has priority in a little. Also in outer rotation by shoulder joint, though there appeared the same difference between A group and B group, B group is tended to be prior to A group in a little. 4. In the view of peak torque for respect to the weight accordance with each velocity of shoulder joint, there did not appear outstanding difference between A group and B group. In outer rotation by the shoulder joint, there was not appeared clear difference between A group and B group. 5. In the concern of the peak torque for respect to the weight accordance with each velocity of shoulder joint, there did not appear outstanding difference between A group and B group in $30^{\circ}/sec$. In outer rotation by the shoulder joint, there was not appeared clear difference between A group and B group. 6. In the concern of the peak torque for respect to the weight accordance with each velocity of shoulder joint, there did not appear outstanding difference between A group and B group in $210^{\circ}/sec$. In outer rotation by the shoulder joint, there was not appeared clear difference between A group and B group. As conclusion, there did not appear a correlation of uniform torque by shoulder joint versus the speed throwing by a pitcher of professional base ball.