• Journal of Radiation Protection and Research
• /
• v.29 no.1
• /
• pp.41-48
• /
• 2004

A safety assessment code, called SAGE (Safety Assessment Groundwater Evaluation), has been developed to describe post-closure radionuclide releases and potential radiological doses for low- and intermediate-level radioactive waste (LILW) disposal in an engineered vault facility in Korea. The conceptual model implemented in the code is focused on the release of radionuclide from a gradually degrading engineered barrier system to an underlying unsaturated zone, thence to a saturated groundwater zone. The radionuclide transport equations are solved by spatially discretizing the disposal system into a series of compartments. Mass transfer between compartments is by diffusion/dispersion and advection. In all compartments, radionuclides ate decayed either as a single-member chain or as multi-member chains. The biosphere is represented as a set of steady-state, radionuclide-specific pathway dose conversion factors that are multiplied by the appropriate release rate from the far field for each pathway. The code has the capability to treat input parameters either deterministically or probabilistically. Parameter input is achieved through a user-friendly Graphical User Interface. An application is presented, which is compared against safety assessment results from the other computer codes, to benchmark the reliability of system-level conceptual modeling of the code.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.133-133
• /
• 2011

최근 나노입자를 이용한 비휘발성 메모리 소자의 제작에 대한 연구가 진행되고 있다. 특히, 실리사이드 계열의 나노입자를 적용한 소자는 일함수가 크지만 실리콘 내의확산 문제를 가지고 있는 금속 나노입자와 달리 현 실리콘 기반의 반도체 공정 적용이 용이한 잇 점을 가지고 있다. 따라서 본 연구에서는 실리사이드 계열의 화합물 중에서 4.63 eV인 Vanadium Silicide ($V_3$Si) 박막을 열처리 과정을 통하여 수 nm 크기의 나노입자로 제작하였다. 소자의 제작은 p-Si기판에 5 nm 두께의 $SiO_2$ 터널층을 dry oxidation 방법으로 성장시킨 후 $V_3$Si 금속박막을 RF magnetron sputtering system을 이용하여 3~5 nm 두께로 tunnel barrier위에 증착시켰다. Rapid thermal annealing법으로 질소 분위기에서 $1000^{\circ}C$의 온도로 30초 동안 열처리하여 $V_3$Si 나노 입자를 형성 하였으며. 20 nm 두께의 $SiO_2$ 컨트롤 산화막층을 ultra-high vacuum magnetron sputtering을 이용하여 증착하였다. 마지막으로 thermal evaporation system을 통하여 Al 전극을 직경 200, 두께 200nm로 증착하였다. 제작된 구조는 metal-oxide-semiconductor구조를 가지는 나노 부유 게이트 커패시터 이며, 제작된 시편은 transmission electron microscopy을 이용하여 $V_3$Si 나노입자의 크기와 균일성을 확인했다. 소자의 전기적인 측정은 E4980A capacitor parameter analyzer와 Agilent 81104A apulse pattern generator system을 이용한 전기용량-전압 측정을 통해 전하저장 효과를 분석하였다.

• Journal of the Korean Vacuum Society
• /
• v.5 no.1
• /
• pp.25-32
• /
• 1996

An ERD-TOF system is constructed for the nondestructive depth profiling of light elements in thin films in the range of several thousand angstroms. The particles, recoiled by 10 $MeV^{35}Cl$ projectiles, were detected by a Time-Of-Flight spectrometer composed of a MCP (Micro Channel Plate) and a SSB (Silicon Surface Barrier) detector. A two parameter data acquisition system composed of two PC's was constructed for registering simultaneous time and energy signals. A $Si_3N_4$/poly-Si/$SiO_2$/Si sample was anlayzed and the result is compared with RBS. The detection limit, maximum probable depth and depth resolution for light elements in silicon are about $4\times10^{14}atoms/\textrm{cm}^2$, 5, 000$\AA$ and 100$\AA$, respectively.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.05a
• /
• pp.109-114
• /
• 2003

Wireless communication systems are inevitable for efficient underwater activities. Because of the poor propagation characteristics of light and electromagnetic waves, acoustic waves are generally used for the underwater wireless communication. Although there are many kinds of information type, visual images take an essential role especially for search and identification activities. For this reason, we developed an acoustic-based underwater image transmission system under a dual use technology project supported by MOCIE (Ministry of Commerce, Industry and Energy). For the application to complicated and time-varying underwater environments all-digital transmitter and receiver systems are investigated. Array acoustic transducers are used at the receiver, which have the center frequency of 32kHz and the bandwidth of 4kHz. To improve transmission speed and quality, various algorithms and systems are used. The system design techniques will be discussed in detail including image compression/ decompression system, adaptive beam- forming, fast RLS adaptive equalizer, ${\partial}/4$ QPSK (Quadrilateral Phase Shift Keying) modulator/demodulator, and convolution coding/ Viterbi. Decoding.

• Bulletin of the Korean Chemical Society
• /
• v.4 no.1
• /
• pp.28-36
• /
• 1983

We considered the tunneling effect on the rate constants calculated from transition-state theory for the H + $D_2$ and D + $H_2$ reactions. A method for evaluating the important parameter Ec (potential barrier height) was proposed. A tunnel-effect correlation factor (TECF) ${\Gamma}_{t}exp{\theta}_t$ was estimated from experimental data, and compared with the corresponding values obtained from many theoretical methods. According to our results, the tunneling effect cannot be negligible around $800^{\circ}$K where the TECF value is ca. 0.8 whereas the factor approaches to unity at T > $2400^{\circ}$K where the tunneling completely disappears. In addition to the above fact, we also found that the TECF for the D + $H_2$ reaction is greater than that of the H + $D_2$ reaction in agreement with Garrett and Truhlar's result. In contrast to our result, however, Shavitt found that the order is reversed, i.e., TECF for (D + $H_2$) is greater than that for (H + $D_2$). We discussed about the Shavitt's result.

• Nuclear Engineering and Technology
• /
• v.53 no.10
• /
• pp.3359-3366
• /
• 2021

An engineered barrier system (EBS) for the deep geological disposal of high-level radioactive waste (HLW) is composed of a disposal canister, buffer material, gap-filling material, and backfill material. As the buffer fills the empty space between the disposal canisters and the near-field rock mass, heat energy from the canisters is released to the surrounding buffer material. It is vital that this heat energy is rapidly dissipated to the near-field rock mass, and thus the thermal conductivity of the buffer is a key parameter to consider when evaluating the safety of the overall disposal system. Therefore, to take into consideration the sizeable amount of heat being released from such canisters, this study investigated the thermal conductivity of Korean compacted bentonites and its variation within a temperature range of 25 ℃ to 80-90 ℃. As a result, thermal conductivity increased by 5-20% as the temperature increased. Furthermore, temperature had a greater effect under higher degrees of saturation and a lower impact under higher dry densities. This study also conducted a regression analysis with 147 sets of data to estimate the thermal conductivity of the compacted bentonite considering the initial dry density, water content, and variations in temperature. Furthermore, the Kriging method was adopted to establish an uncertainty metamodel of thermal conductivity to verify the regression model. The R² value of the regression model was 0.925, and the regression model and metamodel showed similar results.

• Transactions of the Society of Information Storage Systems
• /
• v.1 no.1
• /
• pp.93-98
• /
• 2005

Rewritable optical disk is one of the essential data storage media in these days, which takes advantage of the different optical properties in the amorphous and crystalline states of phase change materials. As well known, data transfer rate is one of the most important parameter of the phase change optical disks, which is mostly limited by the crystallization speed of recording media. Therefore, we doped Sn/Bi to $Ge_2Sb_2Te_5$ alloy in order to improve the crystallization speed and investigated the dependence of phase change characteristics on Sn/Bi doping concentration. The Sn/Bi doped $Ge_2Sb_2Te_5$ thin film was deposited by RF magnetron co-sputtering system and phase change characteristics were investigated by X-ray diffraction (XRD), static tester, UV-visible spectrophotometer, electron probe microanalysis (EPMA), inductively coupled plasma mass spectrometer (ICP-MS) and atomic force microscopy (AFM). Optimum doping concentration of Bi and Sn were 5${\~}$6 at.$\%$ and the minimum time for crystallization was below than 20 ns. This improvement is correlated with the simple crystalline structure of Sn/Bi doped $Ge_2Sb_2Te_5$ and the reduced activation barrier arising from Sn/Bi doping. The results indicate that Sn/Bi might play an important role in the transformation kinetics of phase change materials..

• Nuclear Engineering and Technology
• /
• v.26 no.1
• /
• pp.78-89
• /
• 1994

The radionuclide release rates from the engineered barrier composed of concrete structure and clay-based backfill in a low and intermediate level waste repository were assessed. Four types of release pathway were considered, and the contribution of each pathway to the total release were analyzed. To quantify the effect of uncertainties of input parameter values on the assessment of radionuclide release rates, the Latin Hypercube sampling method was used, and the resulting release rate distribution were determined through a goodness-of-fit test. Finally, the ranges of maxi-mum release rates ore estimated statistically with a confidence level of 95%.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.8
• /
• pp.120-125
• /
• 2002

In the preceding tests using the KSR-III Sub.(I) engines, it was observed that the heat resistant capability of the engines was not enough for the mission. So Sub.(I) Mod. engines were designed and tested. The Sub.(I) Mod. engines have three major design parameters - the arrangement of main injectors, the impinging angle of main injectors and thermal barrier coating. More than twenty experiments were carried on to evaluate engine performance and heat resistance capability with respect to design parameters. In this study, the test results are introduced. Analysing the result of Sub.(I) engine tests, it is found that decreasing the impinging angle, adopting the H-type arrangement(rather than radial type arrangement) and adopting the thermal barrier coating can increase heat resistance capacity substantially. Also, engine performance evaluation is conducted using specific impulse and characteristic velocity parameter. The results show that the performance variation is small(about 5%) and the performance is better in the case of radial arrangement. It is suspected that these phenomena are caused by the change of flame structure atomization mixing characteristic of sprays and the distortion of recirculation zone. Also from the low frequency instability point of view, it is observed that reducing the impinging angle and adopting the H type arrangement can increase the instability characteristics.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.13 no.4
• /
• pp.283-293
• /
• 2015

The buffer is a key component of the engineered barrier system in a high-level radioactive waste (HLW) repository. The present study reviewed the requirements and functional criteria of the buffer reported in literature, and also based on the results, proposed an approach to establish a buffer concept which is applicable to an HLW repository in Korea. The hydraulic conductivity, radionuclide-retarding capacity (equilibrium distribution coefficient and diffusion coefficient), swelling pressure, thermal conductivity, mechanical properties, organic carbon content, and illitization rate were considered as major technical parameters for the functional criteria of the buffer. Domestic bentonite (Ca-bentonite) and, as an alternative, MX-80 (Na-bentonite) were proposed for the buffer of an HLW repository in Korea. The technical specifications for those proposed bentonites were set to parameter values that conservatively satisfy Korea's functional criteria for the Ca-bentonite and Swedish criteria for the Na-bentonite. The thickness of the buffer was determined by evaluating the means of shear behavior, radionuclide release, and heat conduction, which resulted in the proper buffer thickness of 0.25 to 0.5 m. However, the final thickness of the buffer should be determined by considering coupled thermal-hydraulic-mechanical evaluation and economics and engineering aspects as well.