• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.4
• /
• pp.468-480
• /
• 1993

In this paper, at first, the characteristics of double mode SAW (DMS) resonator are analysed by applying the wave guide model and coupled mode theory to 1-port resonator. The DMS resonators (2-pole), which are arranged in a close, parallel configuration of two identical 1-port resonators on a single plate, and 4-pole DMS filters are designed and fabricated at the center frequency of 150.15 MHz with 3-dB bandwidth of 80 KHz. The empirical design characteristics are obtained from the comparison of experimental and theoretical values resulted from several fabrications, and the narrow bandpass filters are implemented on the basis of the above empirical results, which can be used to mobile communication systems. A ST-cut quartz substrate is selected for the stable temperature-frequence characteristics, and high resolution photolithography is applied to the fabrication of filter to get the fine electrode patterns.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.10a
• /
• pp.376-380
• /
• 2009

Surface acoustic wave (SAW) device is widely used as a bandpass filter, a chemical or physical sensor, and an actuator. In this paper, we propose the capacitive gap measurement system with high precision through the signal processing using SAW device. The research process is mainly composed of theoretical part and experimental part. In theoretical part, equivalent circuit model was used to simulate the SAW response by the change of capacitance. In experimental part, commercialized capacitor was used to see the SAW response by the change of load capacitance. After that, gap adjustment system was made physically and the SAW response by the change of gap which caused the capacitance change was measured. And resolution and stroke was decided comparing the signal change and basic measurement noise level.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.11
• /
• pp.1584-1589
• /
• 2013

A new and significantly small guided and resonant structure is suggested to take over bulky metallic hollow waveguides used in military satellite transceivers. Below Ku-band, the conventional waveguides resulting in quite heavy transceivers will be replaced by the low profile SIW(substrate integrated waveguide) structures that are distinguished from the others in that the suggested ones have much lower cut-off frequencies by the circuital configuration of DNG(dobule negative) constitutive parameters and become even smaller than the other SIWs. The design scheme is validated by the circuit and full-wave simulations from the guided, resonant, and coupled structures. Besides, a bandpass filter as the suggested coupled structure is fabricated with a cheap substrate in a low-budget fabrication process and its frequency response is measured as verification of the purpose of the design.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.18 no.2
• /
• pp.85-91
• /
• 1998

In nuclear fuel manufacturing process, end-closure welding has long been recognized as requiring very high integrity. In this basic study, ECT(eddy current testing) method for end-closure welding has been developed to detect end cap weld discontinuities for nuclear fuel safety. In order to improve the inspection reliability, the maximum scanning speed and the maximum frequency is investigated for end-closure welding inspection. The bandpass filter(0-250Hz) is used for removing noise effects. This study shows that ECT method is effective and sensitive for the detection of small defect(0.35mm diameter).

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.7
• /
• pp.28-38
• /
• 1997

Previously, we have proposed the M-BECM(Modified-Band Edge Component Maximization), which is a symbol synchronization algorithm based on spectral line method for all-digital high speed digital communications. However, Until now, the characteristics of the timing detector based on the spectral line method including M-BECM was not analyzed, particularly the effect of a timing offset at the optimal convergence pont. In this paper, we analyze the timing dtector's characteristics of the M-BECM and present optimal design value. First, the expression for the timing detector's mean value(often called its S-Curver) as a function of the normalized symbol timing offset is derived. Next, the P $D_{bias}$, the value for compensating the timing offset at an optimal convergence point, and the bandwidth of bandpass filter in the timing detector are calculated. It is also shown and analyzed that the P $D_{bias}$ is affected by varuous factors such as the excess bandwidth of input signal, frequency offsets, noise and particularly, the excess bandwidth of input signal is a major parameter to decide P $D_{bias}$. Finally, analytic resutls are compared to simulation results.

• Proceedings of the Acoustical Society of Korea Conference
• /
• spring
• /
• pp.115-118
• /
• 2000

Voice conversion technology is essential for TTS systems because the construction of speech database takes much effort. In this paper. male-to-female voice conversion technology in Korean LPC TTS system has been studied. In general. the parameters for voice color conversion are categorized into acoustic and prosodic parameters. This paper adopts LSF(Line Spectral Frequency) for acoustic parameter, pitch period and duration for prosodic parameters. In this paper. Pitch period is shortened by the half, duration is shortened by $25\%, and LSFs are shifted linearly for the voice conversion. And the synthesized speech is post-filtered by a bandpass filter. The proposed algorithm is simpler than other algorithms. for example, VQ and Neural Net based methods. And we don't even need to estimate formant information. The MOS(Mean Opinion Socre) test for naturalness shows 2.25 and for female closeness, 3.2. In conclusion, by using the proposed algorithm. male-to-female voice conversion system can be simply implemented with relatively successful results.

• The Journal of the Acoustical Society of Korea
• /
• v.14 no.4
• /
• pp.64-73
• /
• 1995

We developed a surface acoustic wave (SAW) computer aided design (CAD) for mobile communication using Kaier window function. The systems are composed of modules for designing apodization weighted IDT-uniform IDT, withdrawal weighted IDT-withdrawal weighted IDT, and resonator type. The design of SAW bandpass with center frequencies from 222MHz to 343MHz were simulated by the developed CAD system. Although the method proposed in this paper is formulated primarily for SAW filters, it is equally applicable to finite impulse response (FIR) digital filter design.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.13 no.1
• /
• pp.12-18
• /
• 2013

Motor imagery classification in electroencephalography (EEG)-based brain-computer interface (BCI) systems is an important research area. To simplify the complexity of the classification, selected power bands and electrode channels have been widely used to extract and select features from raw EEG signals, but there is still a loss in classification accuracy in the state-of- the-art approaches. To solve this problem, we propose a discriminative feature extraction algorithm based on power bands with principle component analysis (PCA). First, the raw EEG signals from the motor cortex area were filtered using a bandpass filter with ${\mu}$ and ${\beta}$ bands. This research considered the power bands within a 0.4 second epoch to select the optimal feature space region. Next, the total feature dimensions were reduced by PCA and transformed into a final feature vector set. The selected features were classified by applying a support vector machine (SVM). The proposed method was compared with a state-of-art power band feature and shown to improve classification accuracy.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.2
• /
• pp.339-346
• /
• 1999

A RF receiver section for INMARSAT-C external mounting unit was designed, fabricated and evaluated. Using a INA-03184, the high gain amplifier consists of matched amplifier type. Active bias circuitry can be used to provide temperature stability without requiring the large voltage drop or relatively high-dissipated power needed with a bias stabilization resistor. The bandpass filter was used to reduce a spurious level. As a result, the characteristics of the receiver section implemented here show 60 dB in gain, 44.83 dBc in a spurious level. The voltage standing wave ratios(VSWR)of input output port are less than 1.8:1, respectively.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1942_1943
• /
• 2009

무선통신 시스템의 소형화와 저가격, 고품질, 다기능 재료 및 첨단 가공 기술과 연계된 필터설계 및 제작 기술에 대한 연구가 활발히 진행 중이다. 그러나 무선통신 시스템은 주파수라는 한정된 자원을 사용하기 때문에 주파수 자원의 효율적 관리를 위한 규제나 방안이 필요하고. 이에 따라서 여러 가지 대책과 방안이 필요로 하고 있다. 그래서 필터의 성능개선을 위한 연구가 본질 적으로 중요하게 되었다. 본 논문은 체비세프(Chebyshev)필터와 버터워스(Butterworth)필터를 이용한 대역통과(band pass) 필터를 제안한다. 이 필터는 안정화된 통과대역과 빠른 주파수 응답을 얻기위해 6차 체비세프필터와 8차 버터워스필터를 결합 하였다. 측정된 대역통과 필터는, 차단 영역을 구분하는 스커트(skirt)특성은 날카롭게(sharp) 되었고 통과대역의 평탄도 또한 개선되어짐을 볼 수 있다. 제안된 필터의 중심주파수는 2.5GHz, 대역폭은 200MHz이고, 대역내 평탄도는 0.5dB, 경사도는 오차가 60dB일때 체비세프는 210MHz, 버터워스는 340MHz, 체비세프-버터워스는 290MHz가 되어 버터워스 보다 좋게 되었으며 극점의 배치도 안정적인 결과를 얻었다.