• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.11a
• /
• pp.91-95
• /
• 2002

A very small size BPF is realized using LTCC Multilayer technology. A λ/4 resonator with shunt-to-ground loaded capacitor is used to shorten resonator length and achieve higher qualityfactor. Also this resonator enable BPF to improve out-of-band rejection. Coupling coefficients between coupled stripline resonators and external qualityfactor of a resonator are derived and apply to the filter design. The measured results show a good agreement with the simulation.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.02a
• /
• pp.287-290
• /
• 2003

For microwave device applications, c-axis oriented high temperature superconducting YBa$_2$Cu$_3$O$_{7-{\delta}}$ (HTS-YBCO) epitaxial thin films on the r-cut sapphire substrate(Al$_2$O$_3$) were prepared. In order to reduce the lattice mismatch with a substrate and to enhance the crystallity of HTS thin films, CeO$_2$ buffer layer on the r-cut sapphire substrate was grown by the RF-magnetron sputtering. The YBCO films on the CeO$_2$ buffer layer were deposited using the pulsed-laser deposition (PLD) method. These HTS YBCO /CeO$_2$/Al$_2$O$_3$ multilayer thin films(30 $\times$ 30 mm$^2$) routinely exhibited a critical temperature(T$_{c}$) of 89 K from the R-T measurement. Using HTS YBCO/CeO$_2$ /Al$_2$O$_3$ multilayer thin film. We fabricated and characterized the microwave passive devices (planar type filters) with cryopack-age such as the coupled -line type low-pass filter (LPF) and the open-loop meander type bandpass filter (BPF).filter (BPF).).

• Journal of Korea Multimedia Society
• /
• v.6 no.2
• /
• pp.352-359
• /
• 2003

In this paper, we designed the bluetooth receiver using the microstrip bandpass filter and the high gain low noise amplifier with the 0.2$\mu\textrm{m}$ CMOS technology. A cascode inverter is adopted to implement the low noise amplifier and is one stage amplifier with a voltage reference and without the choke inductor. The designed 2.4GHz LNA was achieved a power gain of 18dB, a noise figure of 2.8dB, and the power consumption of 255mW at 2.5V power supply. Also, the microstrip receiver bandpass filter was designed that the center frequency was 2.45GHz, the bandwidth was 4% and the insert attenuation was -1.9dB. When the microstrip bandpass filter and LNA was simulated together the power gain was 16.3dB.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1332-1-1332-4
• /
• 1998

This paper described design and simulation of the high-Tc superconducting (HTS) microstrip bandpass filter (BPF) on MgO substrate using $Y_1Ba_2Cu_3O_{7-x}$ films that show superconductivity ${at \fallingdotseq}90$ K. Design parameters for the characteristic of the bandpass filter in Ku-band were obtained by approximate design formulas. It used parallel coupled stripline stepped impedance resonators (SIR). Microwave design system, MDS(EEsorf S/W) was used to derive the optimal pattern of the filters and to simulate frequency response. In computer-aided results, optimally designed HTS filters got good performance compared with the gold counter-parts on frequency response $S_{21}$, $S_{11}$.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.2A
• /
• pp.147-152
• /
• 2005

In this paper, we have proposed a novel DGS(Defected Ground Structure) resonator and has designed the band -pass filter using the proposed ${\subset}$ stub-I type DGS resonator. This structure has strong advantages that can vary the retune loss at the passband freely and also can easily tune the attenuation pole frequency at the stopband. The bandpass filter can be made more smaller than the existing filters and be used to find the various applications for eliminating the harmonics and spurious mode at IMT-2000 band.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.2
• /
• pp.79-85
• /
• 2023

To make normal operation of S-Band PSR(Primary Surveillance Radar) which are in operation near distance, Minimizing the mutual frequency interference was studied in this paper. First, the phenomenon of radar receiver was analyzed when the interference between PSR was occurred. And next, the proper S-Band Bandpass filter(BPF) was chosen to deal with the interference. And inhibition performance of BPF was verified by comparative analysis of Radar's RF reception characteristic before and after of BPF application. There is 6.4~7.7 dB passband attenuation when BPF was applied at Radar receiver. So the PSR probability of detection were compared and analyzed to check the radar detection performance was deteriorated or not, And this result proved the usefulness of this study.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.10A
• /
• pp.1031-1036
• /
• 2006

This paper proposes a novel BPF structure with less insertion loss and small size instead of the existing coupled line BPF for the output of the tripler using APDP (Anti-Parallel Diode Pair). This proposed BPF consists of the interdigital capacitor and spiral open stub. The proposed BPF has the insertion loss of less than 0.7dB within the band $(16.41{\sim}19.23GHz)$. The conversion loss of the tripler is about $16.6{\sim}18.5dB$ $(flatness<{\pm}1dB)$ at $5.72{\sim}6.28GHz$ of fundamental frequency. Its fundamental frequency and the fifth harmonic suppression characteristic at 6GHz are -32.16dBc and -44.6dBc, respectively And its phase noise attenuation characteristic is about 9.5dB at 100kHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.5
• /
• pp.486-493
• /
• 2010

This article introduces a novel ultra wideband(UWB) bandpass filter(BPF) with sharp roll-off characteristics in stripline structure. The UWB characteristic is basically obtained from capacitive coupled cross resonator. The resonator has ${\lambda}/2$ length. And at the center of the resonator, two stubs are loaded, one is a ${\lambda}/8$ short-circuited stub and the other is a ${\lambda}/8$ open-circuited stub. The two stubs provide two attenuation poles at lower and upper cutoff frequencies. For input and output lines, two identical capacitively coupled lines have been installed to suppress the unwanted signals in the lower and upper stopbands. The filter has been designed for the U.S. UWB band(3.1~10.6 GHz) with two transmission zeros at 2.4 and 11.1 GHz. The filter has been realized with Low Temperature Core-fired Ceramic(LTCC) green tape which has the dielectric constant of 7.8. Measurement results agree well with HFSS simulation results. Insertion loss less than 0.7 dB and return loss better than 14 dB in the pass band have been measured. The group delay in the center frequency is 0.27 ns and the group delay variation within pass band is less than 0.5 ns. The size of the filter is $6{\times}18{\times}0.6\;mm^3$.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.4C no.6
• /
• pp.300-305
• /
• 2004

In this paper, new design equations based on the pole-zero analysis for multi-layered interdigital stripline linear group delay bandpass filter with tap input ports are presented. As a design example, a four-pole group delay filter with center frequency of 2.14GHz, bandwidth of 160MHz, and group delay variation of $\pm$0.1nS for LTCC technology or multilayered PCB technology is designed. In the design process, it is not necessary to simulate the entire structure, as the simulation of half structures is sufficient. Good results can be attained after the optimizing process was performed three times using the proposed equations and a commercial EM simulator.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.139-142
• /
• 1998

This paper presents a method to determine the rolloff factors of both the digital terrestrial TV modulator and the bandpass filter (BPF) at the digital TV receiver input, using an analytical power spectral density model satisfying given co-channel and adjacent channel protection ratios for the digital terrestrial broadcasting services. Since the proposed method is very simple and effective to use, also can be used regardless of type of systems or modulation techniques, this method is expected to be applied to select some other digital terrestrial broadcasting system specifications.