• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 1999년도 추계 학술발표회 논문집 Proceedings of EESK Conference-Fall
• /
• pp.281-288
• /
• 1999

This paper studied the efficiency of retrofitting of reinforced concrete structure which was not designed to endure an earthquake. The earthquake in Kobe Japan showed that there was a great possibility of having an earthquake even in big city and the damages were concentrated on mid or low story buildings which were not considered to be protected from an earthquake, . This experiment used reinforced concrete structure which restrained side-by-side displacement to test durability against an earthquake. This study deals with the structural performance of reinforced concrete frame structures strengthened with steel materials.

• 한국지반환경공학회 논문집
• /
• 제9권7호
• /
• pp.13-23
• /
• 2008

본 연구에서는 모래다짐말뚝으로 개량된 점성토 지반에 고성토시 발생될 수 있는 측방유동과 교대의 안정성을 파악하기 위하여 원심모형실험과 수치해석을 수행하였다. 원심모형실험과 수치해석은 교대 배면구간을 EPS로 성토한 경우(Case 1)와 토사로 성토한 경우(Case 2)에 대하여 수행하였으며, 모형실험시 교대와 성토체에 potentiometer를 설치하여 교대상부의 수직변위와 수평변위 및 성토체의 수직변위를 측정하였다. 원심모형실험결과 Case 1에서 교대의 수평변위는 1.4cm 정도로 해석결과와 거의 일치하며, 허용기준을 만족하는 것으로 나타났다. 반면, Case 2에서 교대의 수평변위는 12cm 정도로 해석결과에 비해 18% 정도 크게 평가되었으며, 허용기준을 초과하는 것으로 나타났다. 해석결과 Case 1에서 말뚝의 최대수평변위는 1.26cm로 허용 수평변위 기준(1.5cm)을 만족하는 것으로 나타난 반면, Case 2에서 말뚝의 최대 수평변위는 1.005m로 허용기준을 크게 초과하는 것으로 나타났다.

• Restorative Dentistry and Endodontics
• /
• 제20권2호
• /
• pp.812-817
• /
• 1995

Endodontically treated teeth are usually restored for crown protection, aesthetics, and prevention of root canal recontamination. Restoration of these teeth, however, often requires intracanal posts. Various depths and techniques have been recommended for the preparation of post space. Therefore the purpose of this study was to evaluate the effect that pst preparation has on the coronal seal by linear dye penetration of root canals obturated by lateral condensation, vertical condensation, and thermafil techniques. Forty canals of roots of incisors and canines were cleaned and shaped with the use of a step-back technique. Thirty canals were obturated, 10 each with lateral, vertical, and thermafil techhniques. Five root canals were obturated without a root canal sealer and served as positive controls. Another five root canals were obturated, and their coronal half was sealed with sticky wax and served as negative controls. The apical 5 to 6mm of the filling materials were exposed to india ink for 48 hours. The depth of dye penetration was measured in all groups and statistically analyzed (ANOVA). The results were as follows. 1. The apical plugs in the thermafil groups had the highest degree of coronal dye leakage. 2. The group filled by vertical condensation technique had the lowest degree of coronal dye leakage. 3. No significant statistical difference was found in the amount of coronal dye leakage in canals filled by lateral condensation versus those filled by the veritcal condensation technique. 4. Significant statistical differences in coronal dye penetration were found between the canals filled by thermafil and those filled by the lateral or vertical condensation techniques (p<0.05).

• Restorative Dentistry and Endodontics
• /
• 제19권1호
• /
• pp.205-216
• /
• 1994

The purpose of this study is to evaluate of apical plug materials for the contral of extrusion and sealing ability of high-temperature thermoplasticized gutta-percha in plastic root canal blocks. Seventy seven plastic blocks with canal preformed were instrumented with # 50K file 1 mm beyond apical foramen. Blocks were randomly divided into 5 groups of 15 blocks each. Group 1 was filled by high-temperature thermoplasticized gutta-percha only. The another 4 groups were placed with apical plug materials each other and then remaining space was back filled with high temperature thermoplasticized gutta-percha Apical plug materials were used as follows; Group 2: Thermoplasticized gutta-percha (Thermoplasticized gutta-percha group) Group 3 :. Calcium hydroxide powder (Calcium hydroxide group) Group 4 : Silver point (Silver point group) Group 5 : Gutta-percha cone softened by chloroform (Gutta-percha cone group) All the blocks were stored in 100 % relative humidor at room temperature for 14 days. Filling material extruded was removed carefully and then weighed in analytic balance. Each block was placed in centrifuge tube filled with India ink, and then centrifuged for 20 minutes at 3,000 rpm. Apical leakage was measured from the apical foramen to the most coronal level of dye leakage in millimeter by two examiners under a stereoscope. The data were analysed statistically by Student's t-test The obtained results were as follows; 1. The amounts of material extruded through the foramen decreased in all of groups used apical plug materials (P<0.01). 2. Silver point group and gutta-percha cone group were similar linear leakage to high-temperature thermoplasticised gutta-percha technique only (P>0..5). 3. Calcium hydroxide group and thermoplasticized gutta-percha group showed more liner leakage than high-temperature thermoplasticized gutta-percha only (P<0.01, P<0.05). 4. High-temperature thermoplasticized gutta-percha technique with silver point and gutta-percha cone as apical plugs showed less linear leakage and less extrusion of filling material.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.111-114
• /
• 2005

Experimental and numerical studies were carried out in order to investigate the processability and the transcriptability of the injection molding of micro structures. For this purpose, we designed a mold insert having micro rib patterns on a relatively thick base part. Mold insert has a base of 2mm thickness, and has nine micro ribs on that base plate. Width and height of the rib are $300{\mu}m\;and\;1200{\mu}m$, respectively. We found a phenomenon similar to 'race tracking', due to 'hesitation' in the micro ribs. As the melt flows, it starts to cool down and melt front located in the ribs near the gate cannot penetrate further because the flow resistance is large in that almost frozen portion. When the base is totally filled, the melt front away from the gate is not frozen yet. Therefore, it flows back to the gate direction through the ribs. Consequently, transcriptability of the rib far from the gate is better. We also verified this phenomenon via numerical simulation. We further investigated the effects of processing conditions, such as flow rate, packing time, packing pressure, wall temperature and melt temperature, on the transcriptability. The most dominant factor that affects the flow pattern and the transcriptability of the micro rib is flow rate. High flow rate and high melt temperature enhance the transcriptability of micro rib structure. High packing time and high packing pressure result in insignificant dimensional variations of the rib. Numerical simulation also confirms that low flow rate causes a short shot of micro ribs and high wall temperature helps the filling of the micro ribs.

• 한국석유지질학회지
• /
• 제1권1호
• /
• pp.15-27
• /
• 1993

한반도 동해 대륙주변부에서 취득한 에어건 탄성파 탐사자료에 의하면, 이 지역에는 포항-영덕분지, 묵호분지, 후포분지 등, 세 개의 주요 신제삼기 퇴적분지가 대륙붕 및 대륙사면에 형성되어 있다. 이들 퇴적분지에서의 탄성파층서 및 구조분석 결과, 분지의 형성과 퇴적물 충진은 주향이동신장성(transtensional) 및 차후의 압축성(contractional) 광역지구조운동과 밀접한 관계를 갖고 있는 것으로 보인다. 동해 후열도분지가 확장되기 시작하던 올리고세와 전기 마이오세 동안, 한반도 동해 대륙주변부에는 신장성 전단력(tensional shear stress)이 작용하여 후포단층과 양산단층을 따라 우수주향이동 단 층운동이 일어났으며, 이들 평행한 두 단층 사이의 중첩부에는 당겨열림작용(pull-apart opening)에 의해 포항-영덕 분지가 형성되었다. 한편, 한국대지(Korea Plateau)와 접한 동해 대륙주변부에서는 블럭단층운동으로 인해 융기된 고기저(basement highs) 사이에 묵호분지가 형성되었다. 그 후 중기 마이오세 말에 동해가 닫히기 시작하면서, 연구지역의 응력장은 신장성에서 압축성으로 전환되었으며, 후기 마이오세와 전기 플라이오세, 두 번에 걸쳐 지각변형이 일어나면서 분지를 충진한 퇴적층이 변형되었고, 일부지역에서는 융기가 일어났다. 특히, 전기 플라이오세 동안에는 후포단층이 사교이동양상(oblique-slip sense)을 보이면서 재활성화 되었으며, 이로 인해 반지구(half-graben)형태의 후포분지가 형성되었다.

• Journal of Korean Neurosurgical Society
• /
• 제49권1호
• /
• pp.75-78
• /
• 2011

We report a case of pedicle screw loosening treated by modified transpedicular screw augmentation technique using polymethylmethacrylate(PMMA), which used the anchoring effect of hardened PMMA. A 56-year-old man who had an L3/4/5 fusion operation 3 years ago complained of continuous low back pain after this operation. The computerized tomography showed a radiolucent halo around the pedicle screw at L5. We augmented the L5 pedicle screw with modified pedicle screw augmentation technique using PMMA and performed an L3/4/5 pedicle screw fixation without hook or operation field extension. This modified technique is a kind of transpedicular stiffness augmentation using PMMA for the dead space around the loosed screw. After filling the dead space with 1-2 cc of PMMA, we inserted a small screw. Once the PMMA hardened, we removed the small screw and inserted a thicker screw along the existing screw threading to improve the pedicle screws' pullout strength. At 10 months' follow-up, x-ray showed strong fusion of L3/4/5. The visual analogue scale (VAS) of his back pain was improved from 9 to 5. This modified transpedicular screw augmentation with PMMA using anchoring effect is a Simple and effective surgical technique for pedicle screw loosening. However, clinical analyses of long-term follow-up and biomechanical studies are needed.

• 한국지반환경공학회 논문집
• /
• 제3권1호
• /
• pp.47-55
• /
• 2002

압력분사 그라우팅 네일을 이용한 사면보강공법은 천공 후 그라우트재에 압력을 가하여 그라우트재의 천공홀 충전뿐만 아니라 지반으로의 침투주입 효과를 일으켜, 전체적인 보강력 증대를 기대하는 공법이다. 이런 특성을 설계에 반영하기 위해서는 구조재료 자체에 의한 지반보강효과 뿐만 아니라 압력분사 그라우팅에 따른 지반강도의 증진효과를 정량적으로 평가하는 것이 선행되어야 하나 아직까지는 이에 대한 연구가 부족한 실정이다. 따라서 절리가 발달한 풍화암 사면을 대상으로 시험시공 및 계측을 실시하고, 얻어진 계측값을 평가하여 절리가 발달한 풍화암 사면에서의 보강특성을 확인하였다. 또한 계측값으로부터 얻은 보강특성을 설계에 적용하기 위한 역해석 기법을 제안하였으며, 제안된 역해석 기법을 통하여 암반사면에서의 압력분사 그라우팅 네일 공법의 효용성을 확인하였다.

• 터널과지하공간
• /
• 제11권2호
• /
• pp.174-181
• /
• 2001

지하채굴로 생성된 공동이 충전되지 않은 상태로 있으면 공동 천반의 이완과 붕락에 의해 지반침하 및 지표함몰이 발생한다. 특히, 채굴적 상부에 구조물이 건축될 경우 구조물의 안정성에 심각한 영향을 미친다. 본 연구는 A 채광 지역 채굴적의 충전상태 및 채굴적 분포상황을 조사하기 위해 시추조사와 시추공 카메라 조사를 수행하였으며, 표준관입시험을 통해 암반의 물성 및 지반의 지지력을 측정하였다. 또한 전산해석 프로그램(FLAC)을 이용해 채굴적 상부에 구조물이 구축될 경우 발생하는 지반침하 및 지반침하가 구조물의 안정성에 미치는 영향을 조사하였다. 지반조사 결과 채굴적은 대부분 전석이나 광미(tailing)등과 같은 물질로 충전된 상태였고, 충전물의 공학적 분류는 SM에 속했다. 측정 자료를 근거로 실시한 전산해석 결과충전된 채굴적 상부에 구조물이 구축될 경우 구조물 및 지반의 안정성에 는 큰 문제가 없는 것으로 조사되었다.

• 한국의류산업학회지
• /
• 제19권4호
• /
• pp.479-485
• /
• 2017

This study provides basic indices for the development of a pet dog's dummy. Surveys were conducted with 71 owners of small dogs weighing under 10kg as preliminary research for information on pet dogs, uses and complaints about their clothes and demographic information to investigate wearing conditions. We collected pictures of 30 products sold in 12 brands at home and abroad to analyze size, materials, and patterns and investigate the actual production conditions. The survey results on wearing conditions indicated that 'Maltese' was the breed most often raised in households. Dogs weighing 'between 3kg and 4kg' were most common. Dogs under five years of age took up 53.5%. Most of the clothes were 'S' size, followed by 'M' and 'L' Most responded, 'The overall size does not fit' as an inconvenience when worn for long. Second, most brands developed products in three sizes. The displayed details included neck and chest circumference, back length and dummy height. Cotton and artificial leather were used most often for the outer fabric, cotton for the internal filling along with wire and aluminum for some products to maintain shape and motions. Most dummies consisted of back+outer leg, belly, inner leg and sole. Sometimes, a composition line was added by the chest shape, and an incision was placed between the body and leg for breeds with thick legs. Most patterns had a composition line in the leg connected from the belly.