• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.887-890
• /
• 2004

This paper presents a microprocessor controlled electronic ballast for HID lamps, which gives automatic switching between MH and HPS lamps. Lamp identification is carried out by checking variation of lamp impedance at warm-up phase. Direct spread spectrum is done by applying 1 kHz triangular wave for removing acoustic resonance. This frequency modulation of 1 kHz gives also low EMI level. The microprocessor controls the voltage of DC-bus, the voltage of ignition pulses, the power of output. A 250W electronic ballast is implemented with ATmega16 CPU.

• Journal of ILASS-Korea
• /
• v.13 no.2
• /
• pp.91-98
• /
• 2008

In the present study, in order to understand the overall spray combustion characteristics of DME fuel as well as to identify the distinctive differences of DME combustion processes against the conventional hydrocarbon liquid fuels, the sequence of the comparative analysis have been systematically made for DME and n-heptane liquid fuels. To realistically represent the physical processes involved in the spray combustion, this studyemploys the hybrid breakup model, the stochastic droplet tracking model, collision model, high-pressure evaporation model, and transient flamelet model with detailed chemistry. Based on numerical results, the detailed discussions are made in terms of the autoignition, spray combustion processes, flame structure, and turbulence-chemistry interaction in the n-heptane and DME fueled spray combustion processes.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.5
• /
• pp.373-380
• /
• 2009

The evaporation process of multi-component fuel is different from one of a single component, because the properties of each component affects among the components. In actual engine, the spatial distribution of fuel vapor concentration dominates auto-ignition and initial combustion, and depends on the volatility and diffusivity of each component fuel contained in the multi-component fuel. Then, this study proposes a simplified numerical scheme for analysis of evaporation process of multi-component fuel sprays. Evaporation process is calculated by KIVA-II code based on the simple two-phases region that is approximated by modified saturated liquid-vapor line, which was obtained by connecting the 50% distillation temperature for each component under several pressure fields. Consequently, it can be quantitatively simulated that vapor of low boiling fuel component mostly exists around nozzle and spray tip region, the high boiling duel component, on the other hand, mostly appears near the spray tip.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.1
• /
• pp.155-164
• /
• 1996

Dual-fuel engines are being researched with emphasis on the possible types of natural gas supply systems. Hence, a three-dimensional combustion model by using finite volume method was developed to provide a fundamental understanding of the auto-ignition of pilot distillate and subsequent burning of natural gas, when the natural gas as well as the distillate was directly injected into a quiescent diesel engine like combustion bomb tests and the numerical results were investigated for the mixed combustion phenomena. With high-pressure natural gas injection, it was found that the gaseous fuel injection characteristics had to be well harmonised with that of the pilot distillate. For better combustion efficiency, however, further researches are required for the optimisation of injection system in the existence of air motion.

• Journal of the Korean Institute of Gas
• /
• v.14 no.4
• /
• pp.24-30
• /
• 2010

An accurate information of the autoignition temperature(AIT) is important in developing appropriate prevention and control measures in industrial fire. This study measured the AITs of trichlorosliane and dichlosilane(DCS)-trichlorosliane(TCS) mixtures by using ASTM E659-78 apparatus. The experiment AITs of trichlorosliane, TCS(90wt%)-DCS(10wt%) and the TCS(70wt%)-DCS(30wt%) were $225^{\circ}C,\;250^{\circ}C\;and\;236^{\circ}C$, respectively.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.371-374
• /
• 2011

High-resolution numerical study is carried out to investigate the flame stability of the turbulent supersonic combustion in a Dual-Combustion Ramjet (DCR). The auto-ignition in a shear layer between hydrogen/carbon-monoxide syngas and air was studied at elevated enthalpy condition. Comparison of a constant area combustor and a combustor with a small divergence angle shows that the supersonic combustion has a characteristics of the lifted flame and its stability is influenced significantly by the compressibility.

• Journal of Magnetics
• /
• v.16 no.1
• /
• pp.19-22
• /
• 2011

[ $BiFeO_3$ ]is a multiferroic material that attracts attentions of many research groups due to its potential as being ferroelectric and ferromagnetic above room temperature. We have prepared both undoped- and Mn-doped $BiFeO_3$ by sol-gel auto-ignition method. Doping of Mn has resulted in decreasing grain size from 60 to 32 nm. X-ray diffraction data show that the samples are pure and single-phase. Infrared measurements on $BiFeO_3$ and Mn-doped $BiFeO_3$ revealed intrinsic stretching vibrations of tetrahedral sites of $Fe^{3+}$-O and of octahedral $Bi^{3+}$-O as well. On the other hand, as the Mn concentration increases, the magnetic moment of $BiFeO_3$ increases. It gives some suggestions in manipulating structural and magnetic properties of $BiFeO_3$ by doping Mn.

• Journal of the Korean Institute of Gas
• /
• v.10 no.2 s.31
• /
• pp.33-39
• /
• 2006

For the safety design and operation of many gas process, it is necessary to know certain explosion limit, flash point, auto ignition temperature and minimum oxygen concentration of handling substances. Also it is necessary to know explosion limit at high temperature and pressure. For the safe handling of propane, explosion limit and autoignition temperature of combustion characteristics for propane were investigated. By using the literatures data, the lower and upper explosion limits of propane recommended 2.0 vol% and 10.0 vol%, respectively. Also autoignition temperatures of propane with ignition sources recommended $450^{\circ}C$ at the electrically heated cruicible fumace(the whole surface heating) and recommended about $960^{\circ}C$ at the local hot surface. The new equations for predicting the temperature and the pressure dependence of the explosion limits of propane are proposed. The values calculated by the proposed equations were a good agreement with the literature data.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.6
• /
• pp.74-80
• /
• 2008

A combustion of CAI engine is purely dominated by fuel chemical reactions. In order to simulate the combustion of CAI engine, it should be considered the effect of fuel components and chemical kinetics. So it needs enormous computational power. To overcome this problem reduced problem of needing massive computational power, chemical kinetic mechanism and multi-zone method is proposed here in this paper. A reduced chemical kinetic mechanism for a gasoline surrogate was used in this study for a CAI combustion. This gasoline surrogate was modeled as a blend of iso-octane, n-heptane, and toluene. For the analysis of CAI combustion, a multi-zone method as combustion model for a CAI engine was developed and incorporated into the computational fluid dynamics code, STAR-CD, for computing efficiency. This coupled multi-zone model can calculate 3 dimensional computational fluid dynamics and multi-zoned chemical reaction simultaneously in one time step. In other words, every computational cell interacts with the adjacent cells during the chemical reaction process. It can enhance the reality of multi-zone model. A greatly time-saving and yet still relatively accurate CAI combustion simulation model based on the above mentioned two efficient methodologies, is thus proposed.

• Journal of the Korean Institute of Gas
• /
• v.15 no.2
• /
• pp.82-87
• /
• 2011

Heat transfer oils are used in applications such as heating systems of chemical plant, refinery heat exchange systems, gas plant process, injection molding systems, and pulp and paper processing. These oils are extremely stable and resistance to thermal and oxidative degradation. In the event of a spill or accidental release of heat transfer oils, it can be ignite easily when there is an ignition source. This paper discusses the flammability and thermal stabilities of new and used oils. The flammability of the oils are assessed by measuring changes in flash point and auto ignition temperature. The thermal stability of oils are evaluated by the thermal screening unit ($TS^u$) and the differential scanning calorimeter (DSC). From the experimental results, it is suggested to give fire hazard characteristics to safe precautions for the proper use and treatment of heat transfer oils.